Projecting Images. Epson EasyMP Multi PC Projection, Europe EB-595Wi, Europe EB-580S, Europe EB-585WS
Add to My manuals201 Pages
advertisement
Projecting Images
Getting Ready to Project
This section explains the procedure for connecting the projector to a computer with the computer cable and projecting images.
Caution
Be sure to connect the cable of the source to the projector first, and then connect the power cord to the projector.
ON a Connect the projector to the computer with the computer cable.
45 b c
Connect the projector to an electrical outlet with the power cord.
Turn on the projector.
Warning
When turning on the projector, do not look into the projection lens.
This could cause damage to eyesight due to the powerful light emitted.
When turning on the projector at a distance using the remote control, make sure there is no one looking into the lens.
Take particular care when there are children present.
d e
Turn on the computer.
Change the computer's screen output.
When using a laptop computer, you need to change the screen output from the computer.
Hold down the Fn key (function key), and press the b key.
a • The method for changing differs depending on the computer being used. See the documentation supplied with the computer.
• Press the [t] power button twice to turn the projector off.
If the image is not projected, you can change the projected image using one of the following methods.
• Press the [Source Search] button on the control panel or the remote control.
s
"Automatically Detect Input Signals and Change the Projected Image
• Press the button for the target port on the remote control.
s
"Switching to the Target Image Using the Remote Control" p.47
Projecting Images a
After projecting the image, adjust the image if necessary.
s
"Correcting Keystone Distortion" p.52
s
46
Automatically Detect Input Signals and Change the Projected Image (Source Search)
Press the [Source Search] button to project images from the port currently receiving an image.
Using Remote Control Using the Control Panel
When two or more image sources are connected, press the [Source Search] button until the target image is projected.
When your video equipment is connected, start playback before beginning this operation.
Projecting Images
47 a • You can make settings so that images are projected from the same input port the next time the projector is turned on.
s Extended - Operation - Startup Source Search
• The following screen is displayed while no image signals are input.
Switching to the Target Image Using the Remote
Control
You can change directly to the target image by pressing the following buttons on the remote control.
Remote control
A Each time the button is pressed, it cycles through the images being input from the following sources.
• Computer1 port
• Computer2 port
B Each time the button is pressed, it cycles through the images being input from the following sources.
• S-Video port
• Video port
• HDMI1/MHL port
• HDMI2 port
C Each time the button is pressed, it cycles through the images being input from the following sources.
• USB Display
• Images from the device connected to the USB-A port
D Switches to the image from the network connected device.
Projecting Images
48
Projecting with USB Display
You can use the supplied or a commercially available USB cable to connect the projector to a computer to project images from the computer.
You can send the computer's audio with the projected image.
Set USB Type B to USB Display/Easy Interactive Function or Wireless
Mouse/USB Display to use USB Display on EB-595Wi/EB-585Wi/
EB-575Wi.
s Extended - USB Type B
System Requirements
For Windows
OS Windows 2000 * 1
Windows XP
Windows Vista
Windows 7
Professional 32 bit
Home Edition 32 bit
Tablet PC Edition 32 bit
Ultimate 32 bit
Enterprise 32 bit
Business 32 bit
Home Premium 32 bit
Home Basic 32 bit
Ultimate 32- and 64-bit
Enterprise 32- and 64-bit
Professional 32- and 64-bit
Home Premium 32- and 64-bit
Home Basic 32 bit
Starter 32 bit
Windows 8
Windows 8.1
Windows 8 32- and 64-bit
Windows 8 Pro 32- and 64-bit
Windows 8 Enterprise 32- and
64-bit
Windows 8.1 32- and 64-bit
Windows 8.1 Pro 32- and 64-bit
Windows 8.1 Enterprise 32- and
64-bit
CPU
Amount of Mem‐ ory
Mobile Pentium III 1.2 GHz or faster
Recommended: Pentium M 1.6 GHz or faster
256 MB or more
Recommended: 512 MB or more
Hard Disk Space 20 MB or more
Display Resolution of no less than 640x480 and no higher than
1600x1200.
Display color of 16-bit color or greater
* 1 Service Pack 4 only
For OS X
OS
CPU
Mac OS X 10.5.x 32 bit
Mac OS X 10.6.x 32- and 64-bit
OS X 10.7.x 32- and 64-bit
OS X 10.8.x
OS X 10.9.x
Power PC G4 1GHz or faster
Recommended: Core Duo 1.83GHz or faster
512 MB or more Amount of Memo‐ ry
Hard Disk Space 20 MB or more
Projecting Images
49
Display Resolution of no less than 640x480 and no higher than
1680x1200.
Display color of 16-bit color or greater
Connecting for the First Time
The first time you connect the projector and the computer using the USB cable, the driver needs to be installed. The procedure is different for
Windows and OS X.
a • You do not need to install the driver the next time you connect.
• When inputting images from multiple sources, change the input source to USB Display.
• If you are using a USB hub, operations may not be performed correctly. Connect the USB cable directly to the projector.
• You cannot change option settings while using USB Display.
For Windows a Connect the computer's USB port to the projector's USB-B port using the supplied or a commercially available USB cable.
a
For Windows 2000 or Windows XP, a message asking you if you want to restart your computer may be displayed. Select
No .
For Windows 2000
Double-click Computer - EPSON PJ_UD - EMP_UDSE.EXE.
For Windows XP
Driver installation starts automatically.
For Windows Vista/Windows 7/Windows 8/Windows 8.1
When the dialog box is displayed, click run EMP_UDSE.EXE.
When the License Agreement screen is displayed, click Agree.
b c d
Computer images are projected.
It may take a while for computer images to be projected. Until the computer images are projected, leave the equipment as is and do not disconnect the USB cable or turn off the power of the projector.
Disconnect the USB cable when you are finished.
When disconnecting the USB cable, there is no need to use Safely
Remove Hardware .
a • If it is not installed automatically, double-click My Computer
- EPSON PJ_UD - EMP_UDSE.EXE on your computer.
• If nothing is projected, click All Programs - EPSON
Projector - Epson USB Display - Epson USB Display
Ver.x.xx
on your computer.
• When using a computer running Windows 2000 under user authority, a Windows error message is displayed and you may not be able to use the software. In this case, try updating
Windows to the latest version, restart, and then try to connect again.
For more details, contact your local dealer or the nearest address provided in the following document.
s Epson Projector Contact List
Projecting Images b c d
For OS X a Connect the computer's USB port to the projector's USB-B port using the supplied or a commercially available USB cable.
The Setup folder of USB Display is displayed in the Finder.
Double-click the USB Display Installer icon.
Follow the on-screen instructions to install.
e f
When the License Agreement screen is displayed, click Agree.
Enter the administrator authority password and start the installation.
When the installation is complete, the USB Display icon is displayed in the Dock and menu bar.
Computer images are projected.
It may take a while for computer images to be projected. Until the computer images are projected, leave the equipment as is and do not disconnect the USB cable or turn off the power of the projector.
When you have finished, select Disconnect from the menu bar or from the USB Display icon on the Dock. You can then disconnect the USB cable.
a • If the USB Display Setup folder is not displayed automatically in the Finder, double-click EPSON PJ_UD - USB Display
Installer on your computer.
• If nothing is projected for some reason, click the USB
Display icon in the Dock.
• If there is no USB Display icon on the Dock, double-click
USB Display in the application folder.
• If you select Exit from the USB Display icon on the Dock,
USB Display does not start automatically when you connect the USB cable.
Uninstalling
For Windows 2000 a b c d
Click Start, select Settings, and then click Control Panel.
Double-click Add/Remove Programs.
Click Change or Remove Programs.
Select Epson USB Display and click Change/Remove.
For Windows XP a b c
Click Start, and then click Control Panel.
Double-click Add or Remove Programs.
Select Epson USB Display, and then click Remove.
For Windows Vista/Windows 7 a b c
Click Start, and then click Control Panel.
Click Uninstall a program under Programs.
Select Epson USB Display, and then click Uninstall.
For Windows 8/Windows 8.1
a Open Charms, and then select Search. Right-click (hold down)
Epson USB Display Ver.x.xx.
b c
Select Uninstall from the app bar.
Select Epson USB Display, and then click Uninstall.
50
Projecting Images d Follow the on-screen instructions to uninstall.
For OS X a b
Double-click Applications - USB Display - Tool.
Run USB Display Uninstaller.
51
advertisement
Related manuals
advertisement
Table of contents
- 8 Projector Features
- 8 Interactive Features (Easy Interactive Function) (EB-595Wi/EB-585Wi/EB-575Wi only)
- 8 Enabling Projection from a Short Distance
- 8 Connecting to a Network and Projecting Images from the Computer's Screen
- 9 Enhanced Security Functions
- 9 Enlarge and Project Your Files with the Document Camera
- 11 Part Names and Functions
- 11 Front/Side
- 12 Top/Side
- 13 Interface
- 14 Base
- 15 Attaching the Feet (only Models with Feet Supplied)
- 16 Control Panel
- 17 Remote Control
- 19 Replacing the Remote Control Batteries
- 20 Remote Control Operating Range
- 20 Interactive Pen (EB-595Wi/EB-585Wi/EB-575Wi only)
- 21 Replacing the Battery for the Interactive Pen
- 22 Replacing the Tip of the Interactive Pen
- 23 Pen Tray (EB-595Wi/EB-585Wi/EB-575Wi only)
- 23 Touch Unit (EB-595Wi only)
- 23 Front
- 24 Rear
- 26 Installing the Projector
- 26 Installation Methods
- 27 When Using the Interactive Features (EB-595Wi/EB-585Wi/EB-575Wi only)
- 28 Setting up the Touch Unit (EB-595Wi only)
- 29 Connecting Equipment
- 29 Connecting a Computer
- 31 Connecting a Smartphone or Tablet Device
- 32 Connecting Image Sources
- 35 Connecting USB Devices
- 37 Connecting a Microphone
- 38 Connecting External Equipment
- 40 Connecting a LAN Cable
- 41 Installing the Optional Wireless LAN Unit
- 42 Connecting Multiple Projectors (EB-595Wi/EB-585Wi/EB-575Wi only)
- 45 Projecting Images
- 45 Getting Ready to Project
- 46 Automatically Detect Input Signals and Change the Projected Image (Source Search)
- 47 Switching to the Target Image Using the Remote Control
- 48 Projecting with USB Display
- 48 System Requirements
- 49 Connecting for the First Time
- 50 Uninstalling
- 52 Adjusting Projected Images
- 52 Correcting Keystone Distortion
- 52 H/V-Keystone
- 53 Quick Corner
- 55 Adjusting the Image Size
- 55 Adjusting the Position of the Image (Image Shift)
- 56 Adjusting the Vertical Position of the Image (Models Supplied with the Feet only)
- 56 Raising the Height of the Image
- 56 Lowering the Height of the Image
- 56 Adjusting the Horizontal Position of the Image (Models Supplied with the Feet only)
- 57 Correcting the Focus
- 59 Adjusting the Volume
- 60 Selecting the Projection Quality (Selecting Color Mode)
- 60 Setting Auto Iris
- 61 Changing the Aspect Ratio of the Projected Image
- 61 Changing Methods
- 61 Changing the Aspect Mode (EB-595Wi/EB-585Wi/EB-585W/EB-575Wi/EB-575W only)
- 63 Changing the Aspect Mode (EB-580/EB-570 only)
- 65 Interactive Feature Modes
- 66 Drawing on a Projected Image (Annotation Mode)
- 67 Using the Projected Screen as a Whiteboard (Whiteboard Mode)
- 68 Controlling Computer Features from a Projected Screen (Computer Interactive Mode)
- 68 Computer Interactive Mode System Requirements
- 68 Using Computer Interactive Mode
- 71 Easy Interactive Driver System Requirements (OS X only)
- 72 Installing Easy Interactive Driver on OS X
- 73 Using the Interactive Pens
- 74 Pen Calibration
- 75 Calibrating Automatically
- 76 Calibrating Manually
- 78 Adjusting the Pen Operation Area
- 80 Using Your Finger for Interactive Touch Operations (EB-595Wi only)
- 80 Safety Instructions for Interactive Touch Operations
- 80 Laser Warning Labels
- 81 Using Interactive Touch Operations with Your Finger
- 82 Calibrating for Touch Operations with Your Finger
- 86 Interacting with the Screen
- 86 Switching the Interactive Mode
- 87 Annotation Mode and Whiteboard Mode Toolbars
- 88 Selecting Line Width and Color
- 89 Selecting Whiteboard Templates
- 89 Projector Control Toolbar
- 90 Selecting Network Device Display from the Projector Control Toolbar
- 92 Using the Interactive Features over a Network
- 92 Precautions When Connecting to a Projector on a Different Subnet
- 94 Windows Pen Input and Ink Tools
- 94 Enabling Windows Pen Input and Ink Features
- 95 Using Windows Pen Input and Ink Features
- 97 Projection Functions
- 97 Projecting Images Stored on a USB Storage Device (PC Free)
- 97 Specifications for Files that Can Be Projected Using PC Free
- 97 PC Free Examples
- 98 PC Free Operating Methods
- 99 Projecting the Selected Images or Movies
- 100 Projecting Image Files in a Folder in Sequence (Slideshow)
- 101 Image File Display Settings and Slideshow Operation Settings
- 102 Hiding the Image and Sound Temporarily (A/V Mute)
- 102 Freezing the Image (Freeze)
- 103 Pointer Function (Pointer)
- 103 Enlarging Part of the Image (E-Zoom)
- 104 Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)
- 106 Saving a User's Logo
- 108 Saving User Pattern
- 110 Security Functions
- 110 Managing Users (Password Protection)
- 110 Kinds of Password Protection
- 110 Setting Password Protection
- 111 Entering the Password
- 112 Restricting Operation (Control Panel Lock)
- 113 Anti-Theft Lock
- 113 Installing the Wire Lock
- 114 Monitoring and Controlling
- 114 About EasyMP Monitor
- 114 Message Broadcasting
- 114 Changing Settings Using a Web Browser (Web Control)
- 114 Projector Setup
- 115 Displaying the Web Control Screen
- 115 Displaying the Web Remote Screen
- 116 Using the Mail Notification Function to Report Problems
- 117 Reading Error Notification Mail
- 117 Management Using SNMP
- 118 ESC/VP21 Commands
- 118 Command List
- 118 Cable Layouts
- 119 About PJLink
- 120 About Crestron RoomView®
- 120 Operating a Projector from Your Computer
- 125 Using the Configuration Menu
- 126 List of Functions
- 126 Configuration Menu Table
- 127 Network Menu
- 128 Image Menu
- 129 Signal Menu
- 131 Settings Menu
- 132 Extended Menu
- 135 Easy Interactive Function Setting Items
- 136 Network Menu
- 137 Notes on Operating the Network Menu
- 137 Soft Keyboard Operations
- 138 Basic Menu
- 139 Wireless LAN Menu
- 140 Security Menu
- 141 Wired LAN Menu
- 142 Mail Menu
- 143 Others Menu
- 144 Reset Menu
- 144 ECO Menu
- 145 Info Menu (Display only)
- 146 Reset Menu
- 147 Performing Batch Setup for Multiple Projectors
- 149 Using the Help
- 150 Problem Solving
- 150 Reading the Indicators
- 154 When the Indicators Provide No Help
- 155 Problems Relating to Images
- 155 No Images Appear
- 156 Moving Images Are Not Displayed (only the Moving Image Portion Turns Black)
- 156 Projection Stops Automatically
- 156 The Message Not supported Is Displayed
- 157 The Message No Signal Is Displayed
- 157 Images Are Fuzzy, Out of Focus, or Distorted
- 158 Interference or Distortion Appear in Images
- 159 The Mouse Cursor Flickers (only when Projecting USB Display)
- 159 The Image Is Truncated (Large) or Small, or the Aspect Is Not Suitable
- 160 Image Colors Are Not Right
- 160 Images Appear Dark
- 161 Problems when Projection Starts
- 161 The Projector Does Not Turn on
- 161 Problems with the Interactive Features (EB-595Wi/EB-585Wi/EB-575Wi only)
- 161 Cannot Draw on the Projected Screen
- 162 Cannot Operate a Computer from the Projected Screen after Connecting to the Computer
- 162 The Message An error occurred in the Easy Interactive Function. Is Displayed
- 163 Computer's Mouse Does Not Work Correctly
- 163 The Interactive Pen Does Not Work
- 164 The Response Time for the Interactive Pen Is Slow (only when Projecting USB Display)
- 164 Cannot Perform Touch Operations Correctly (EB-595Wi only)
- 165 Cannnot Adjust the Angle of Touch Unit (EB-595Wi only)
- 165 The Dot Moves Automatically or Does Not Move to the Next Position during Calibrating Manually
- 165 Other Problems
- 165 No Sound Can Be Heard or the Sound Is Faint
- 166 No Sound Can Be Heard from the Microphone
- 166 There Is Noise in the Audio (only when Projecting USB Display)
- 167 The Remote Control Does Not Work
- 167 I Want to Change the Language for Messages and Menus
- 167 Mail Is Not Received even if an Error Occurs with the Projector
- 168 Cannot Change Settings Using a Web Browser
- 169 About Event ID
- 171 Cleaning
- 171 Cleaning the Projector's Surface
- 171 Cleaning the Projection Window
- 171 Cleaning the Obstacle Sensor
- 172 Cleaning the Air Filter
- 175 Replacing Consumables
- 175 Replacing the Lamp
- 175 Lamp Replacement Period
- 176 How to Replace the Lamp
- 179 Resetting the Lamp Hours
- 179 Replacing the Air Filter
- 179 Air Filter Replacement Period
- 179 How to Replace the Air Filter
- 184 Optional Accessories and Consumables
- 184 Optional Accessories
- 184 Consumables
- 185 Screen Size and Projection Distance
- 185 Projection Distance (for EB-595Wi/EB-585Wi/EB-585W/EB-575Wi/EB-575W)
- 186 Projection Distance (for EB-580/EB-570)
- 188 Supported Monitor Displays
- 188 Supported Resolutions
- 188 Computer Signals (Analog RGB)
- 188 Component Video
- 188 Composite Video
- 188 HDMI Input Signal
- 189 MHL Input Signal
- 190 Specifications
- 190 Projector General Specifications
- 196 Appearance
- 198 Glossary
- 200 General Notes
- 200 Wireless Telegraphy Act Regulations
- 200 About Notations
- 201 General Notice: