advertisement
Components
EMU26400
Top cowling release lever
The top cowling can be removed by operating the cowling release lever. Pulling the front lever unlocks the top cowling for removal.
A
B
ZMU01863
Bolt tightening torque:
42.0 Nm (4.2 kgf-m, 31 ft-lb)
EMU26341
Tilt support lever for power trim and tilt model
To keep the outboard motor in the tilted up position, lock the tilt support lever to the clamp bracket.
1
ZMU03518
When installing the top cowling:
1.
Set the top cowling straight down onto the engine, being careful to avoid catching spark plug wires or other wires.
2.
Align the three cowling hooks with the locks on the bottom cowling.
3.
Press down on the top of the cowling at the front and both sides of the back until the three locks click.
ZMU03979
1. Tilt support lever
ECM00660
NOTICE
Do not use the tilt support lever or knob when trailering the boat. The outboard motor could shake loose from the tilt support and fall. If the motor cannot be trailered in the normal running position, use an additional support device to secure it in the tilt position.
ZMU03519
4.
To make sure the cowling is locked properly push the cowling from each side. If it lifts, repeat step 3.
ECM00070
NOTICE
● Make sure the cowling lock connection
24
advertisement
Related manuals
advertisement
Table of contents
- 7 Safety information
- 7 Outboard motor safety
- 7 Propeller
- 7 Rotating parts
- 7 Hot parts
- 7 Electric shock
- 7 Power trim and tilt
- 7 Engine shut-off cord (lanyard)
- 7 Gasoline
- 8 Gasoline exposure and spills
- 8 Carbon monoxide
- 8 Modifications
- 8 Boating safety
- 8 Alcohol and drugs
- 8 Personal flotation devices
- 8 People in the water
- 8 Passengers
- 8 Overloading
- 9 Avoid collisions
- 9 Weather
- 9 Accident reporting
- 9 Boat education and training
- 10 Passenger training
- 10 Boating safety publications
- 10 Laws and regulations
- 10 Boating organizations
- 10 road)
- 11 sound signals
- 11 Rules when encountering vessels
- 12 Other special situations
- 15 General information
- 15 Identification numbers record
- 15 Outboard motor serial number
- 15 Key number
- 16 Read manuals and labels
- 16 Warning labels
- 19 requirements
- 19 Specifications
- 20 Installation requirements
- 20 Boat horsepower rating
- 20 Mounting motor
- 20 Remote control requirements
- 20 Battery requirements
- 20 Specifications of Battery
- 20 Mounting battery
- 21 Multiple batteries
- 21 Propeller selection
- 21 Start-in-gear protection
- 21 Engine oil requirements
- 22 Fuel requirements
- 22 Gasoline
- 22 Ring Free Fuel Additive
- 23 Muddy or acidic water
- 23 Anti-fouling paint
- 23 Motor disposal requirements
- 23 Emission control information
- 23 North American models
- 25 Components
- 25 Components diagram
- 25 Remote control box
- 26 Remote control lever
- 26 Neutral interlock trigger
- 26 Neutral throttle lever
- 27 Choke switch
- 27 Throttle friction adjuster
- 28 Choke knob for pull type
- 28 Main switch
- 28 remote control
- 29 bottom engine cowling
- 29 Trim tab with anode
- 30 and tilt model
- 30 Top cowling release lever
- 31 Flushing device
- 32 Instruments and indicators
- 32 Digital tachometer
- 32 Trim meter
- 32 Hour meter
- 32 Oil level indicator (digital type)
- 33 Overheat-alert indicator
- 33 Digital speedometer
- 33 Speedometer
- 34 Fuel gauge
- 34 Trip meter / Clock / Voltmeter
- 35 Fuel level-alert indicator
- 35 indicator
- 35 Analog tachometer
- 35 indicators 2)
- 36 Analog trim meter
- 37 Engine control system
- 37 Alert system
- 37 Overheat alert
- 37 alert
- 39 Installation
- 39 Mounting the outboard motor
- 41 Operation
- 41 First-time operation
- 41 Breaking in engine
- 41 Getting to know your boat
- 41 Checks before starting engine
- 42 Fuel level
- 42 Remove cowling
- 42 Fuel system
- 42 Controls
- 43 Engine shut-off cord (lanyard)
- 43 Engine
- 43 storage
- 43 Flushing device
- 44 Install cowling
- 44 system
- 45 Battery
- 46 Filling fuel and engine oil
- 46 fuel joint
- 46 Filling oil
- 48 Oil level indicator operation
- 49 Operating engine
- 49 Feeding fuel
- 49 Starting engine
- 51 Checks after starting engine
- 51 Cooling water
- 51 Warming up engine
- 51 Choke start models
- 51 Checks after engine warm-up
- 51 Shifting
- 51 Stop switches
- 52 Shifting
- 53 Stopping boat
- 53 Stopping engine
- 53 Procedure
- 53 Trimming outboard motor
- 54 and tilt)
- 54 Adjusting boat trim
- 55 Tilting up and down
- 56 and tilt models)
- 57 trim and tilt models)
- 57 Shallow water
- 57 Power trim and tilt models
- 58 Cruising in other conditions
- 59 Maintenance
- 59 outboard motor
- 59 Storing outboard motor
- 59 Procedure
- 60 Lubrication (oil injection models)
- 61 measures
- 61 Flushing power unit
- 62 Cleaning the outboard motor
- 62 motor
- 62 Periodic maintenance
- 63 Replacement parts
- 63 Maintenance interval guidelines
- 64 Maintenance chart
- 67 Greasing
- 68 Checking fuel filter
- 68 Inspecting idling speed
- 69 Checking water in engine oil tank
- 69 Checking wiring and connectors
- 69 Checking propeller
- 70 Removing propeller
- 70 Installing propeller
- 71 Changing gear oil
- 72 anode(s)
- 73 models)
- 73 Connecting the battery
- 74 Disconnecting the battery
- 75 Trouble Recovery
- 75 Troubleshooting
- 78 Temporary action in emergency
- 78 Impact damage
- 78 Replacing fuse
- 79 operate
- 79 Starter will not operate
- 80 Emergency starting engine
- 81 Engine fails to operate
- 81 Low oil level alert activates
- 82 Top cowling does not unlock
- 82 Treatment of submerged motor
- 83 Consumer information
- 83 for U.S.A. and Canada
- 85 YEAR LIMITED WARRANTY
- 88 THE USA OR CANADA