Setting functions and options. Honeywell Thermostat RTH6500WF, RTH6580WF, RTH6500WF

Setting functions and options

You can change options for a number of system functions. Available functions depend on the type of system you have. The functions, along with available options, are described on pages 50–54.

This thermostat is pre-set for a single-stage heating/cooling system. Setting function 1 for a heat pump will adjust the default settings.

69-2718ES—01

48

69-2718ES_A.indd 48 8/13/2012 3:01:35 PM

Setting functions and options

1 Press Fan and s simultaneously and hold for approximately 3 seconds. The screen will change to display two numbers and the button designations will be Done, Back, blank,

Next.

2 Press Next until you see the function number—the larger number on the left— you want to set.

3 Change options for any function by pressing s or t until the correct option (smaller number on right) is displayed.

4 Repeat Steps 2 and 3 until you have set all functions that you wish to change.

5 When you have made all changes, press

Done to save and exit.

49

69-2718ES_A.indd 49

HOLD

MCR33883

HOLD

MCR33884

69-2718ES—01

8/13/2012 3:01:39 PM

System setup

(See page 48 for instructions.)

Function Settings & Options

1 Select System

Type

If you are not sure of your heating/ cooling system type or have other questions, go to wifithermostat.com

2 Heat Pump

Changeover Valve

(for heat pumps only)

0 Heat/cool: Gas, oil or electric heating with central air conditioning.

1 Heat pump: Heat pump without backup or auxiliary heat.

2 Heat only: Gas, oil or hot water heat without central air conditioning.

3 Heat only with fan: Gas, oil or electric heat without central air conditioning.

4 Cool only: Central air conditioning only.

5 Heat pump: Heat pump with backup or auxiliary heating.

6 Heat/Cool Multiple stages: 2 heat stages (wires on W and W2), 2 cooling stages (wires on Y and Y2).

7 Heat/Cool Multiple stages: 2 heat stages (wires on W and W2), 1 cooling stage (wire on Y).

8 Heat/Cool Multiple stages: 1 heat stage (wires on W), 2 cooling stages

(wire on Y and Y2).

0 Cooling changeover valve: Use this setting if you connected a wire labeled “O” to the O/B terminal.

1 Heating changeover valve: Use this setting if you connected a wire labeled “B” to the O/B terminal.

69-2718ES—01

50

69-2718ES_A.indd 50 8/13/2012 3:01:40 PM

System setup

(See page 48 for instructions.)

3

Function

Heating Fan

Control

5 Heating Cycle

Rate

6 Heating Cycle

Rate Stage 2

12 Manual/Auto

Changeover

See page 47 for more information.

Settings & Options

0 Gas or oil heat: Use this setting if you have a gas or oil heating system

(system controls fan operation).

1 Electric heat: Use this setting if you have an electric heating system

(thermostat controls fan operation).

5 Gas or oil furnace: Standard gas/oil furnace (less than 90% efficiency).

9 Electric furnace: Electric heating systems.

3 Hot water or high-efficiency furnace: Hot water system or gas furnace

(more than 90% efficiency).

1 Gas/oil steam or gravity system: Steam or gravity heat systems.

0 Manual changeover (Heat/Cool/Off).

1 Automatic changeover (Heat/Cool/Auto/Off). Automatically turns on Heat or Cool based on room temperature. Note: System maintains minimum

3°F difference between heat and cool settings.

51

69-2718ES_A.indd 51

69-2718ES—01

8/13/2012 3:01:40 PM

System setup

(See page 48 for instructions.)

Function Settings & Options

13 Smart Response

Technology

See page 45 for more information.

1 On

0 Off

14 Temperature

Format (°F/°C)

0 Fahrenheit

1 Celsius

16 Schedule Options 1 Program schedule is on (7-day programmable).

0 Program schedule is off. Thermostat can not be programmed.

69-2718ES—01

52

69-2718ES_A.indd 52 8/13/2012 3:01:40 PM

System setup

(See page 48 for instructions.)

Function Settings & Options

36 Device Name

This name will identify the thermostat when you view it remotely.

If you register multiple thermostats, give each one a different name.

52 = Thermostat

1 Basement

2 Bathroom

3 Bathroom 1

4 Bathroom 2

5 Bathroom 3

6 Bedroom

7 Bedroom 1

8 Bedroom 2

9 Bedroom 3

10 Bedroom 4

11

12

Boat House

Bonus Room

13 Computer Room 28 Kitchen 2

14 Den

15 Dining Room

16 Exercise Room 30 Library

17 Family Room 31 Living Room 45 Rec Room

18

19

24

25

Fireplace

Foyer

22 Great Room

23 Guest Room

Gym

Kid's Room

26 Kitchen

27 Kitchen 1

35 Media Room 49 Studio

36 Music Room 50 Sun Room

39 Office 1

40 Office 2

44 Porch

32 Lower Level 46 Sewing Room

33 Master Bath 47 Spa

20 Game Room 34 Master Bed 48 Storage Room

21 Garage

37 Nursery

38 Office

51 Theater

52 Thermostat

53 Upper Level

54 Utility Room

41 Pantry 55 Walk In Closet

42 Play Room 56 Wine Cellar

29 Laundry Room 43 Pool Room 57 Workshop

53

69-2718ES_A.indd 53

69-2718ES—01

8/13/2012 3:01:40 PM

System setup

(See page 48 for instructions.)

Function Settings & Options

38 Wi-Fi On/Off 1 Wi-Fi is on and can be connected to a Wi-Fi network.

0 Wi-Fi is off. Thermostat cannot be connected to a Wi-Fi network. If you are not connecting the thermostat to a Wi-Fi network this will remove the text Wi-Fi Setup from the messaging center.

39 Wi-Fi Connection 1 Connected to Wi-Fi network. This is set automatically when the thermostat is connected to the Wi-Fi network.

0 Set to 0 to disconnect from the Wi-Fi network.

42 Show period and day of week

85 Restore Schedule

Defaults

90 Restore Original

Settings

0 Period and day are not shown on the home screen.

1 Period and day are shown on the home screen.

0 Continue using programmed schedule.

1 Restore thermostat program to energy saving settings

0 No

1 Disconnects thermostat from Wi-Fi and restores original settings (erases customizations).

69-2718ES—01

54

69-2718ES_A.indd 54 8/13/2012 3:01:40 PM