Honeywell RTH6580 Owner Manual
Add to My manuals
140 Pages
Honeywell RTH6580 is a Wi-Fi programmable thermostat that can be controlled remotely via the Internet. It is easy to install and use, and it comes with many features that can help you save energy and money. With its Smart Response Technology, the thermostat learns your heating and cooling patterns and adjusts the temperature accordingly. It also has compressor protection, which helps to prevent damage to your air conditioner. The thermostat can be programmed with up to four different temperature settings per day, and it can be set to automatically switch between heating and cooling modes. It also has a permanent override button that allows you to temporarily override the programmed settings.
advertisement
![Honeywell RTH6580 Owner Manual | Manualzz Honeywell RTH6580 Owner Manual | Manualzz](http://s1.manualzz.com/store/data/007430239_1-c785e18ceb21f84fbbbf146f90999f17-360x466.png)
User Guide
Wi-Fi Programmable
Thermostat
RTH6500WF Wi-Fi Series
In the box you will find
• Thermostat
• Wallplate (attached to thermostat)
• Screws and anchors
• Quick Start Guide
• Thermostat ID Card
• Wire labels
• User Guide
• Quick Reference Card
69-2718EF—01
ii
Welcome
Congratulations on your purchase of a
Honeywell Wi-Fi programmable thermostat.
When registered to Honeywell’s Total Connect
Comfort Solutions, you can remotely monitor and control the heating and cooling system in your home or business—you can stay connected to your comfort system wherever you go.
Honeywell’s Total Connect Comfort is the perfect solution if you travel frequently, own a vacation home, a business or manage an
Investment property or if you are simply looking for peace of mind.
This thermostat works with common 24 volt systems such as forced air, hydronic, heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a gas fireplace, or with 120/240 volt systems such as baseboard electric heat.
MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact the Thermostat Recycling Corporation at www.thermostat-recycle.org or 1-800-238-8192 for information on how and where to properly and safely dispose of your old thermostat.
NOTICE: To avoid possible compressor damage, do not run air conditioner if the outside temperature drops below 50°F (10°C).
Need help?
Visit wifithermostat.com or call 1-855-733-5465 for assistance before returning the thermostat to the store.
69-2718EF—01
2
Table of contents
About your new thermostat
Controls and Home screen quick reference ............................................ 5
Preset energy-saving schedules ................. 6
Installation
Installing your thermostat ............................ 8
Connecting to your Wi-Fi network ............. 26
Registering your thermostat online ........... 31
Operation
Setting the the time and day ..................... 36
Setting the fan ........................................... 37
Selecting system mode ............................. 38
Adjusting program schedules .................... 39
Overriding schedules temporarily ............. 40
Overriding schedules permanently ........... 41
Unregistering thermostat........................... 42
Disconnecting Wi-Fi .................................. 43
Special features ........................................ 45
Setting functions and options .................... 48
Appendices
Frequently asked questions ...................... 55
Troubleshooting ......................................... 61
Limited warranty ........................................ 67
69-2718EF—01
3
Features of your Wi-Fi thermostat
With your new thermostat, you can:
•
Connect to the Internet to monitor and control your heating/cooling system
•
View and change your heating/cooling system settings
•
View and set temperature and schedules
•
Receive alerts via email and get automatic upgrades
Your new thermostat provides:
•
Smart Response Technology
•
Compressor protection
•
Heat/cool auto changeover
69-2718EF—01
4
Controls and home screen quick reference
Once your Wi-Fi thermostat is installed, it will display the home screen. Portions of this display will change depending on how you are viewing it.
Set up messages describe steps in the
Wi-Fi set up process
HOLD
Wi-Fi status
Temperature adjustment buttons
Permanent override button
M31586
Set clock, day, or schedule
Select fan settings
Select system mode
Additional settings
The screen lights when you press any button. It stays lit for 8 seconds after you complete changes.
Preset energy-saving schedules
This thermostat is pre-set with energy-saving program settings for four time periods.
Using the default settings can reduce your heating/cooling expenses by as much as 33% if used as directed. Savings may vary depending on geographic region and usage. To change the settings, see pages 39–41.
WAKE
6:00 am
LEAVE
8:00 am
RETURN
6:00 pm
SLEEP
10:00 pm
Default Heat Settings
70
°
62
70
62
°
°
°
Default Cool Settings
78
°
85
78
°
°
82
°
69-2718EF—01
6
Setting up your thermostat
Setting up your Wi-Fi programmable thermostat is easy. It is preprogrammed and ready to go as soon as it is installed and registered.
1
Install your thermostat.
2
3
Connect your home Wi-Fi network.
Register online for remote access.
Before you begin,
you may want to watch a brief installation video. Use the QR Code
®
at the front of this guide, or go to wifithermostat.com/support
Installing your thermostat
You might need the following tools to install this thermostat:
• No. 2 Phillips screwdriver
• Small pocket screwdriver
• Pencil
• Level (optional)
• Drill and bits (3/16” for drywall,
7/32” for plaster) (optional)
• Hammer (optional)
• Electrical tape (optional)
1 Switch OFF power to your heating/cooling system.
Important!
To protect your equipment, switch OFF the power to your heating/ cooling system at the breaker box or the system switch.
or
Circuit breaker box
Heating/cooling system power switch
69-2718EF—01
8
Installing your thermostat
2 Remove old thermostat faceplate and leave wires connected.
2a Take a picture of the wire connections for later reference.
2b If no wire is connected to a terminal labeled C or no C terminal exists on the old thermostat, view the
Alternate Wiring videos at wifithermostat.com/videos
If you have an older thermostat with a sealed mercury tube, turn to page 2 for proper disposal instructions.
C
C
Important!
C wire is required and is the primary power source for your thermostat. Without a C wire, your thermostat will not power up.
Terminal designation
MCR33823
Installing your thermostat
3 Label wires.
Do not label by wire color.
Use the supplied sticky tags to label each wire as you disconnect it.
Label wires according to the old thermostat terminal designations, not by wire color.
Note:
If no tag matches a wire terminal label, write the terminal label on a blank tag.
4 Remove wallplate.
Remove the old wallplate from the wall after all wires have been labeled and disconnected.
69-2718EF—01
10
C
C
Sticky tags
Blank sticky tags
MCR31537
Terminal designation
Installing your thermostat
5 Separate Wi-Fi thermostat and its wallplate.
On your new thermostat, grasp the finger holds on the top and bottom of the wallplate with one hand and the thermostat (front) with the other hand.
Pull pieces apart.
Thermostat
PULL HERE
TO REMOVE
Finger holds
11
PULL HERE
TO REMOVE
Wallplate (back view)
M33856
69-2718EF—01
Installing your thermostat
6 Mount wallplate for Wi-Fi thermostat.
Mount your new wallplate using screws and anchors included with the thermostat.
If necessary:
Drill 3/16-in holes for drywall.
Drill 7/32-in holes for plaster.
Note:
You may be able to use your existing wall anchors. Hold the wallplate up to the existing anchors to check for alignment
Wallplate
69-2718EF—01
12
MCR33857
Installing your thermostat
Important!
The Wi-Fi thermostat requires a C wire to operate. The C, or common, wire brings 24 VAC power to the thermostat. Many older mechanical or battery operated thermostats do not require a C wire. If you don’t have a C wire, try:
• Looking for an unused wire that is pushed into the wall. Connect that wire to C and check that it is connected to the 24 VAC common at your heating/cooling system.
Note:
Not all heating/cooling systems label the 24 VAC common C. Check your system manual or contact the manufacturer to find out which terminal is the 24 VAC common.
View the Alternate Wiring videos at wifithermostat.com/videos
Wiring
For
conventional
heating/cooling systems (natural gas, oil or electric furnace, air conditioner), see page 14. See “Glossary” on page 64 for further definition.
For a
heat pump
system, see page 15. See “Glossary” on page 64 for further definition.
13
69-2718EF—01
Installing your thermostat
Wiring (conventional system)
7A Wire the Wi-Fi thermostat to your conventional system.
a Starting with the C Wire, match the sticky tag on the wire to the terminal labels.
You must have a C wire. See page 13.
b Loosen screw, insert wire on inside edge of terminal, then tighten screw.
c Verify wire is firmly secured by gently pulling on wire. d Repeat steps a–c for all other wires.
e Push any excess wire back into the wall opening after all wires are installed.
f Continue to page 20.
Labels don’t match?
See alternate wiring key on pages 16–17.
69-2718EF—01
14
Remove metal jumper
only
if you have both
R and RC wires
G W
K Y2 W2 G W
C
C
K L AUX/E
G O/B C
Y
R
Y R RC
CONVENTIONAL
Y R RC
HEAT PUMP
MCR33878
Note:
The wiring for your application might be different from the shown above.
Installing your thermostat
Wiring (heat pump system only)
Labels don’t match?
See alternate wiring key on pages 18–19.
7B Wire Wi-Fi thermostat to your heat pump.
a Starting with the C Wire, match the sticky tag on the wire to the terminal labels.
You must have a C wire. See page 13.
b Loosen screw, insert wire on inside edge of terminal, then tighten screw.
c Verify wire is firmly secured by gently pulling on wire. d Repeat steps a–c for all other wires.
e Push any excess wire back into the wall opening after all wires are installed
.
f Continue to page 20.
Aux
G O
K L
AUX/E
G O/B C
Y R
Y R RC
HEAT PUMP
MCR33877
Note:
If old thermostat has separate wires on
AUX and
E, place both wires into the E/AUX terminal.
If old thermostat has wire on
AUX with a jumper to E, place wire on
E/AUX terminal. No jumper is required.
15
Note:
The wiring for your application might be different from the wiring shown above.
69-2718EF—01
Installing your thermostat
Alternate wiring (conventional system)
Use this if your wire labels don’t match the terminal labels.
Note:
You must have a C wire or equivalent.
See page 13.
Y2 W2 G
F
W
W1
H
C
X
B
C1
Y
Y1
M
2
R
RH
4
V
RC
R
1
K Y2 W2 G W C Y R RC
3
CONVENTIONAL
MCR33885
See key to
1
–
3 on page 17.
69-2718EF—01
16
Installing your thermostat
Alternate wiring key (conventional system)
1
2
3
Do not use K terminal. For future use.
If your old thermostat had both R and RH wires, remove metal jumper.
Connect the R wire to the RC terminal, and the RH wire to the R terminal.
Remove metal jumper connecting R and RC only if you must connect both
R and RC.
17
69-2718EF—01
Installing your thermostat
Alternate wiring (heat pump system only)
Use this if your wire labels don’t match the terminal labels.
Note:
You must have a C wire or equivalent.
See page 13.
L
F
2
E AUX
X
X2
W
W1
W2
G
F
3
4
O
H
B
4
C
X
B
5
Y
Y1
M
6
R
V
VR
RC
R
1
7
K L
AUX/E
G O/B
C
69-2718EF—01
18
Y R RC
HEAT PUMP
MCR33886
See key to
1
–
7 on page 19.
Installing your thermostat
Alternate wiring key (heat pump system only)
3
4
1
2
5
6
7
Do not use
K terminal. For future use.
If old thermostat has separate wires on
AUX and E, place both wires into the E/AUX terminal. If old thermostat has wire on AUX with a jumper to E, place wire on E/AUX terminal. No jumper is required.
If your old thermostat had an
O wire and not a B wire, attach the O wire to the O/B terminal.
If your old thermostat had separate O and B wires, attach the B wire to the C terminal. If another wire is attached to the C terminal, check wifithermostat.com for help. Attach the O wire to the
O/B terminal.
If your old thermostat had separate Y1, W1 and W2 wires, check wifithermostat.com for help.
If your old thermostat had both V and VR wires, check wifithermostat.com for help.
Leave metal jumper between R and RC terminals in place.
19
69-2718EF—01
Installing your thermostat
8 Insert quick reference card.
Fold quick reference card along score lines, and slide it into the slot on the back of the thermostat.
MCR33916
Quick reference card
69-2718EF—01
20
Back of thermostat
MCR33858
Installing your thermostat
9 Attach thermostat to wallplate.
Align the thermostat to the wallplate and then snap into place.
21
HOLD
M33860
69-2718EF—01
Installing your thermostat
10 Switch heating/cooling system ON.
Important!
10a Verify that the C wire is connected at the thermostat and at the heating/cooling system.
10b Make sure the heating/ cooling system door is firmly secured.
10c Switch power back ON for your heating/cooling system at the breaker box or its power switch.
69-2718EF—01
22
or
Circuit breaker box system power switch
Installing your thermostat
11 Set clock to current day and time.
11a Press s
or t
to set clock.
11b Press
Set Day
.
11c Press s
or t
to select the day of week.
11d Press
Done
to save.
(Press and hold a st
button to quickly change a setting.)
23
HOLD
MCR33908
HOLD
MCR33909
69-2718EF—01
Installing your thermostat
12 Determine your heating/cooling system type.
Important!
Heating/cooling system type must be set so that your thermostat operates properly and does not damage your system.
12a If your system type is conventional single stage (natural gas-powered single stage with a/c), continue to “Connecting to your Wi-Fi network” on page 26.
12b
If your system is:
• Conventional multistage heat and cool
• Any type of heat pump
• Hydronic
If you are not sure of your heating/cooling system type or have other questions, go to wifithermostat.com/support
• Other
You MUST change the system type by setting system function 1. See page 48 to match your thermostat to your system type.
69-2718EF—01
24
Installing your thermostat
Congratulations! Your thermostat is operational.
13 Test your thermostat
13a Press the
System
button to change to heating or cooling and begin operation.
13b For remote access to your thermostat, continue to “Connecting to your Wi-Fi network” on page 26.
MCR33880
Heating/cooling system not turning on? Refer to page 62 or FAQ at wifithermostat.com/support
25
69-2718EF—01
Connecting to your Wi-Fi network
To complete this process, you must have a wireless device connected to your home wireless network. Any of these device types will work:
• Tablet (recommended)
• Laptop (recommended)
• Smartphone
If you get stuck...
at any point in this procedure, restart the thermostat by removing the thermostat from the wallplate, wait for 10 seconds, and snap it back onto the wallplate. Go to Step 1 in this procedure, starting on page 27.
View the Wi-Fi Enrollment video at wifithermostat.com/videos
69-2718EF—01
26
Connecting to your Wi-Fi network
1 Connect to your thermostat.
1a Make sure the thermostat displays
Wi-Fi Setup.
1b On the wireless device (laptop, tablet, smartphone), view the list of available Wi-Fi networks.
1c Connect to the network called
NewThermostat_123456 (the number will vary).
Note:
If you are asked to specify a home, public, or office network, select Home Network.
27
HOLD
M33852
69-2718EF—01
Connecting to your Wi-Fi network
2 Join your home network.
2a Open your web browser to access the
Thermostat Wi-Fi Setup page. The browser should automatically direct you to the correct page; if it does not, go to http://192.168.1.1
2b Find the name of your home network on this page and select it.
Note:
Some routers have enhanced features such as guest networks; use your home network.
2c Complete the instructions for joining your Wi-Fi network and click on the Connect button.
(Depending on your network setup, you may see an instruction such as Enter Password for your home network.)
Note:
If you did not correctly connect to the thermostat, you may see your home router page. If so, return to Step 1.
69-2718EF—01
28
Connecting to your Wi-Fi network
Note:
If your Wi-Fi network does not appear in the list on the Thermostat Wi-Fi Setup page:
• Try performing a network rescan by pressing the Rescan button. This is helpful in areas with a lot of networks.
• If you are connecting to a hidden network, then enter the network SSID in the textbox, select the encryption type from the drop down menu, and click on the
Add button. This manually adds the network to the top of the list. Click on the new network in the list and enter the password if necessary. Click on Connect to join the network.
29
69-2718EF—01
Connecting to your Wi-Fi network
3 Make sure your thermostat is connected.
While the connection is in process, your thermostat will flash
Wait for up to 3 minutes. When the connection is complete, the display will show
Wi-Fi
Setup Connection Success. The Wi-Fi signal strength will appear in the top-right corner.
After about 60 seconds, the home screen will appear and
Register at Total Connect will flash until registration is complete.
If you don’t see these messages, see page 26.
To register online for remote access to your thermostat continue on page 31.
Note:
If the thermostat displays
Connection Failure or continues to display
Wi-Fi Setup, confirm you correctly entered your home network password in step 2. If correct, refer to the FAQ at wifithermostat.com/support
69-2718EF—01
30
M33875
M33876
Registering your thermostat online
To view and set your Wi-Fi thermostat remotely, you must have a Total Connect
Comfort account. Use the following steps.
1 Open the Total Connect Comfort web site.
Go to mytotalconnectcomfort.com
View the Wi-Fi Thermostat Registration video at wifithermostat.com/videos
31
69-2718EF—01
Registering your thermostat online
2 Login or create an account.
If you have an account, click
Login
– or – click Create An Account.
2a Follow the instructions on the screen.
2b
Check your email
for an activation message from My Total Connect
Comfort. This may take several minutes.
Note:
If you do not receive a response, check your junk mailbox or use an alternate e-mail address.
2c
Follow activation instructions
in the email.
2d Log in.
69-2718EF—01
32
Registering your thermostat online
3 Register your Wi-Fi thermostat.
After you are logged in to your Total Connect Comfort account, register your thermostat.
3a Follow the instructions on the screen. After adding your thermostat location, you must enter the thermostat’s unique identifiers:
• MAC ID
• MAC CRC
Note:
These IDs are listed on the
Thermostat ID Card included in the thermostat package. The IDs are not case sensitive.
Thermostat ID Card
Use the MAC ID and CRC ID to register this product at mytotalconnectcomfort.com
Carte d’identification de thermostat
Utilisez l’identification MAC et l’identification CRC pour enregistrer ce produit à mytotalconnectcomfort.com
Tarjeta de identificación del termostato
Utilice la identificación MAC y la identificación CRC para inscribir este producto en mytotalconnectcomfort.com
® U.S. Registered Trademark.
© 2012 Honeywell International Inc.
69-2723EFS—01 M.S. 04-12
Printed in U.S.A.
MAC ID
HONEYWELL MODEL:
MAC ID: MAC CRC:
69-2723EFS-01
MAC CRC
33
69-2718EF—01
Registering your thermostat online
3b When the thermostat is successfully registered, the Total Connect Comfort registration screen will display a SUCCESS message.
In the thermostat display, you will see
Setup Complete for about 90 seconds.
69-2718EF—01
34
Registering your thermostat online
3c Also notice that your thermostat displays its signal strength.
Congratulations! You’re done.
You can now control your thermostat from anywhere through your tablet, laptop, or smartphone
Total Connect Comfort free app is available for Apple
®
iPhone
®
, iPad
®
and iPod touch
®
devices at iTunes
Google Play
®
or at
®
for all Android™ devices.
GET IT ON
Download on
iTunes
35
69-2718EF—01
Setting the time and day
1 Press
Set Clock/Day/Schedule
, then press s or t to set clock.
2 Press
Set Day
, then press s
or t to select the day of week.
3 Press
Done
to save.
Note:
If the
Set Clock/Day/Schedule option is not displayed, press
Done
.
Note:
If the display flashes Set Clock, the thermostat will follow your settings for the
Monday “Wake” time period until you reset the time and day.
69-2718EF—01
36
HOLD
HOLD
MCR33855
Setting the fan
Press
Fan
to select
On or Auto (toggle to re-select).
Auto: Fan runs only when the heating or cooling system is on. Auto is the most commonly used setting.
On: Fan is always on.
Note:
Options may vary depending on your heating/cooling equipment.
37
MCR33895
69-2718EF—01
Selecting system mode
Press
System
to select:
Heat: Controls only the heating system.
Cool: Controls only the cooling system.
Off: Heating/cooling systems are off.
Auto: Selects heating or cooling depending on the indoor temperature.
Em Heat (heat pumps with aux. heat):
Controls auxiliary/emergency heat.
Compressor is off.
MCR33880
Note:
Depending on how your thermostat was installed, you may not see all system settings.
69-2718EF—01
38
Adjusting program schedules
1 Press
Set Clock/Day/Schedule
, then
Set Schedule
.
2 Press s
or t to set your Monday (Mon) Wake time, then press
Next
.
3 Press s
or t to set the temperature for this period, then press
Next
.
4 Set time and temperature for the next time period (Leave). Repeat Steps 2 and 3 for each time period.
5 Press
Next
to set time periods for the next day.
Repeat Steps 2 through 4 for each day.
6 Press
Done
to save and exit.
Note:
Make sure the thermostat is set to the system mode you want to program (Heat or Cool).
39
MCR33892
69-2718EF—01
Overriding schedules temporarily
Press s
or t
to immediately adjust the temperature.
The new temperature will be maintained only until the next programmed time period begins.
To cancel the temporary setting at any time, press
Cancel
. The program schedule will resume.
HOLD
MCR33896
69-2718EF—01
40
Overriding schedules permanently
1 Press
HOLD
to permanently adjust the temperature. This will turn off the program schedule.
2 Press s
or t
to adjust the temperature setting. The temperature you set will be maintained 24 hours a day until you manually change it or press
Cancel
to resume the program schedule
HOLD
MCR33897
41
69-2718EF—01
Unregistering thermostat
If you remove the thermostat from your
Total Connect Comfort website account
(for example, you’re moving and leaving the thermostat behind), the thermostat will display
Register at Total Connect until it is re-registered.
69-2718EF—01
42
M33876
Disconnecting Wi-Fi
Replacing your router
If you disconnect the thermostat from your Wi-Fi network:
1 Enter system setup (see page 48).
2 Change setting 39 to 0 (see page 54).
The screen will display
Wi-Fi Setup.
Re-connect to a Wi-Fi network by following the steps on page 26.
M33855
Turning Wi-Fi off
If you do not plan to control the thermostat remotely, you can remove the Wi-Fi Setup message from the screen:
1 Enter system setup (see page 48).
2 Change setting 38 to 0 (see page 54). Wi-Fi Setup will be removed from the screen.
If you want to connect to the Wi-Fi network later, change setting 38 back to 1.
43
69-2718EF—01
Software updates
Honeywell periodically issues updates to the software for this thermostat. The updates occur automatically through your Wi-Fi connection. All your settings are saved, so you will not need to make any changes after the update occurs.
While the update is taking place, your thermostat screen flashes Updating and shows the percentage of the update that has occurred. When the update is complete, your home screen will appear as usual.
Note:
If you are not connected to Wi-Fi, you will not get automatic updates.
69-2718EF—01
44
M34001
Percentage of update complete
Smart Response Technology
This feature allows the thermostat to “learn” how long the heating/cooling system takes to reach programmed temperature settings, so the temperature is reached at the time you set.
For example: Set the Wake time to 6:00 am, and the temperature to 70°. The heat will come on before 6:00 am, so the temperature is 70° by 6:00 am.
Note:
System setting function 13 controls
Smart Response Technology. See “Smart
Response Technology” on page 52.
The message Recovery is displayed when the system is activated before a scheduled time period.
M33881
45
69-2718EF—01
Compressor protection
This feature forces the compressor to wait a few minutes before restarting, to prevent equipment damage.
M33882
The message
Cool On (or
Heat On for a heat pump) will flash during the wait time.
69-2718EF—01
46
Auto changeover
This feature is used in climates where both air conditioning and heating are used on the same day.
When the system is set to
Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature.
Heat and cool settings must be at least
3 degrees apart. The thermostat will automatically adjust settings to maintain this
3-degree separation.
Note:
System setting function 12 controls
Auto changeover. See “Manual/Auto
Changeover” on page 51.
47
MCR33893
69-2718EF—01
Setting functions and options
You can change options for a number of system functions. Available functions depend on the type of system you have. The functions, along with available options are described on pages 50–54.
This thermostat is pre-set for a single-stage heating/cooling system.
Setting function 1 for a heat pump will adjust the default settings.
69-2718EF—01
48
Setting functions and options
1 Press
Fan
and s simultaneously and hold for approximately 3 seconds. The screen will change to display two numbers and the button designations will be
Done, Back, blank,
Next.
2 Press
Next
until you see the function number—the larger number on the left— you want to set.
3 Change options for any function by pressing s
or t until the correct option
(smaller number on right) is displayed.
4 Repeat Steps 2 and 3 until you have set all functions that you wish to change.
5 When you have made all changes, press
Done
to save and exit.
49
HOLD
MCR33883
HOLD
MCR33884
69-2718EF—01
System setup
(See page 48 for instructions.)
1
Function
Select System
Type
If you are not sure of your heating/ cooling system type or have other questions, go to wifithermostat.com
2
Heat Pump
Changeover Valve
(for heat pumps only)
Settings & Options
0 Heat/cool: Gas, oil or electric heating with central air conditioning.
1 Heat pump: Heat pump without backup or auxiliary heat.
2
Heat only: Gas, oil or hot water heat without central air conditioning.
3 Heat only with fan: Gas, oil or electric heat without central air conditioning.
4 Cool only: Central air conditioning only.
5
Heat pump: Heat pump with backup or auxiliary heating.
6 Heat/Cool Multiple stages: 2 heat stages (wires on W and W2), 2 cooling stages (wires on Y and Y2).
7 Heat/Cool Multiple stages: 2 heat stages (wires on W and W2), 1 cooling stage (wire on
Y).
8 Heat/Cool Multiple stages: 1 heat stage (wires on W), 2 cooling stages
(wire on Y and Y2).
0
Cooling changeover valve: Use this setting if you connected a wire labeled “O” to the O/B terminal.
1 Heating changeover valve: Use this setting if you connected a wire labeled “B” to the O/B terminal.
69-2718EF—01
50
System setup
(See page 48 for instructions.)
3
Function
Heating Fan
Control
5
Heating Cycle
Rate
6
Heating Cycle
Rate Stage 2
12
Manual/Auto
Changeover
See page 47 for more information.
Settings & Options
0 Gas or oil heat: Use this setting if you have a gas or oil heating system
(system controls fan operation).
1 Electric heat: Use this setting if you have an electric heating system
(thermostat controls fan operation).
5 Gas or oil furnace: Standard gas/oil furnace (less than 90% efficiency).
9 Electric furnace: Electric heating systems.
3
Hot water or high-efficiency furnace: Hot water system or gas furnace
(more than 90% efficiency).
1 Gas/oil steam or gravity system: Steam or gravity heat systems.
0 Manual changeover (Heat/Cool/Off).
1 Automatic changeover (Heat/Cool/Auto/Off). Automatically turns on Heat or Cool based on room temperature. Note: System maintains minimum
3°F difference between heat and cool settings.
51
69-2718EF—01
System setup
(See page 48 for instructions.)
Function Settings & Options
13
Smart Response
Technology
See page 45 for more information.
1 On
0 Off
14
Temperature Format (°F/°C)
0 Fahrenheit
1 Celsius
16
Schedule Options
1 Program schedule is on (7-day programmable).
0 Program schedule is off. Thermostat can not be programmed.
69-2718EF—01
52
System setup
(See page 48 for instructions.)
Function Settings & Options
36
Device Name
This name will identify the thermostat when you view it remotely.
If you register multiple thermostats, give each one a different name.
52 = Thermostat
1 Basement
2 Bathroom
3 Bathroom 1
4 Bathroom 2
5 Bathroom 3
6 Bedroom
7 Bedroom 1
8 Bedroom 2
9 Bedroom 3
10 Bedroom 4
11 Boat House
12 Bonus Room
16
17
18
19
Exercise Room
Family Room
Fireplace
Foyer
20 Game Room
21 Garage
22 Great Room
23 Guest Room
24 Gym
25 Kid's Room
26 Kitchen
27 Kitchen 1
13 Computer Room 28 Kitchen 2
14 Den
15 Dining Room
30
31
Library
Living Room
44
45
Porch
Rec Room
32 Lower Level 46 Sewing Room
33 Master Bath 47 Spa
34 Master Bed 48 Storage Room
35 Media Room 49 Studio
36 Music Room 50 Sun Room
37 Nursery
38 Office
39 Office 1
40 Office 2
41 Pantry
51 Theater
52 Thermostat
53 Upper Level
54 Utility Room
55 Walk In Closet
42 Play Room 56 Wine Cellar
29 Laundry Room 43 Pool Room 57 Workshop
53
69-2718EF—01
System setup
(See page 48 for instructions.)
Function Settings & Options
38
42
Wi-Fi On/Off
Show period and day of week
1 Wi-Fi is on and can be connected to a Wi-Fi network.
0 Wi-Fi is off. Thermostat cannot be connected to a Wi-Fi network. If you are not connecting the thermostat to a Wi-Fi network this will remove the text
Wi-Fi Setup from the messaging center.
39
Wi-Fi Connection
1 Connected to Wi-Fi network. This is set automatically when the thermostat is connected to the Wi-Fi network.
0 Set to 0 to disconnect from the Wi-Fi network.
0 Period and day are not shown on the home screen.
1 Period and day are shown on the home screen.
85
Restore Schedule
Defaults
90
Restore Original
Settings
0 Continue using programmed schedule.
1 Restore thermostat program to energy saving settings
0 No
1 Disconnects thermostat from Wi-Fi and restores original settings (erases customizations).
69-2718EF—01
54
Frequently asked questions
:
A Contact the manufacturer of the router or check the router documentation.
Q Why am I not seeing my Wi-Fi setup page?
:
:
thermostat again.
Q Why isn’t my thermostat connecting to my Wi-Fi router even though it is very close to the thermostat?
55
69-2718EF—01
Frequently asked questions back of the thermostat (visible when removed from wallplate). Each thermostat has a unique MAC
ID and MAC CRC.
A Verify that the thermostat is correctly enrolled on your home Wi-Fi network. The message center will display
Wi-Fi Setup or Register at Total Connect. You might also see the Wi-Fi Signal strength icon. Verify that the Wi-Fi router has a good internet connection. On your computer, verify that you can open the site at mytotalconnectcomfort.com
If you cannot open the site, switch off the internet modem for a few seconds, then power it back on.
69-2718EF—01
56
Frequently asked questions
account.
A Check your email and ensure that you received an activation email. Follow the instructions to activate your account and then login to the website.
confirmation email.
A Most standard routers can be set up to be a repeater. You can also purchase and install a Wi-Fi repeater.
For more FAQs, see wifithermostat.com/support
57
69-2718EF—01
Troubleshooting
Lost Signal
If the no-Wi-Fi indicator displays in place of the
Wi-Fi strength indicator in the upper right hand corner of the home screen:
• Check another device to be sure Wi-Fi is working in your home; if not, call your Internet
Service Provider.
• Move the router.
• Restart the thermostat: remove it from the wallplate, wait 10 seconds, and snap it back onto the wallplate. Return to Step 1 of
Connecting to your Wi-Fi network.
69-2718EF—01
58
Troubleshooting
Error Codes
For certain problems, the thermostat screen will display a code that identifies the trouble. Initially, error codes are displayed alone in the time area of the screen; after a few minutes, the home screen is displayed and the code alternates with the time.
Error Code
E01
During Wi-Fi Setup, the router lost power.
Action
• Ensure your router has power.
• If trying to connect to a hidden or manually added network, confirm the router has power and is working.
M33999
E02
Invalid Wi-Fi password. This code displays for 30 seconds, then the thermostat will re-enter
Wi-Fi Setup mode.
• Re-enter password for your home Wi-Fi network.
• Repeat setup process and confirm your password for your home
Wi-Fi network.
59
69-2718EF—01
Troubleshooting
Error Code Action
E42
Router is not issuing an IP address to the thermostat.
• Wait for 30 minutes, connection can take several minutes.
• If still no connection, remove thermostat from wallplate for 10 seconds, then reconnect it (see page 26).
• Verify your router is correctly setup to automatically give IP addresses.
E43
No internet connection.
Thermostat cannot communicate to Total
Connect Comfort.
• Make sure the Internet cable is plugged in.
• Reboot the router.
E99
General error Remove thermostat from wallplate for
10 seconds, then reconnect it (see page
26).
69-2718EF—01
60
M33998
Troubleshooting
If you have difficulty with your thermostat, please try the following suggestions.
Most problems can be corrected quickly and easily.
Display is blank
• Check circuit breaker and reset if necessary.
• Make sure power switch at heating and cooling system is on.
• Make sure furnace door is closed securely.
• Make sure C wire is connected (see page 13).
Cannot change system setting to Cool
• Check Function 1: System Type to make sure it is set to match your heating and cooling equipment (see page 50).
Fan does not turn on when heat is required
• Check Function 3: Heating Fan Control to make sure it is set to match your heating equipment (see page 51).
Cool On or Heat
On is flashing on the screen
• Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor.
61
69-2718EF—01
Troubleshooting
Heat pump issues cool air in heat mode, or warm air in cool mode
Heating or cooling system does not respond
• Check Function 2: Heat Pump Changeover Valve to make sure it is properly configured for your system (see page 50).
• Press
System
to set system to Heat. Make sure the temperature is set higher than the Inside temperature.
• Press
System
to set system to Cool. Make sure the temperature is set lower than the Inside temperature.
• Check circuit breaker and reset if necessary.
• Make sure power switch at heating & cooling system is on.
• Make sure furnace door is closed securely.
• Wait 5 minutes for the system to respond.
69-2718EF—01
62
Troubleshooting
Heating system is running in cool mode
• Check Function 1: System Type to make sure it is set to match your heating and cooling equipment (see page 50).
Heating and cooling equipment are running at the same time
• Check Function 1: System Type to make sure it is set to match your heating and cooling equipment (see page 50).
• Grasp and pull thermostat away from wallplate. Check to make sure bare wires are not touching each other.
• Check thermostat wiring is correct.
63
69-2718EF—01
Glossary
C wire
The “C” or common wire brings 24 VAC power to the thermostat from the heating/cooling system.
Some older mechanical or battery operated thermostats may not have this wire connection. It is necessary for establishing a Wi-Fi connection to your home network.
Heat Pump heating/cooling system
Heat pumps are used to heat and cool a home. If your old thermostat has a setting for auxiliary or emergency heat, you likely have a heat pump.
Conventional heating/cooling system
Non–heat pump type systems; these include air handlers, furnaces or boilers that run on natural gas, oil or electricity. They may or may not include an air conditioner.
Jumper
A small piece of wire that connects two terminals together.
MAC ID, MAC CRC
Alphanumeric codes that uniquely identify your thermostat.
QR Code
®
Quick response code. A two-dimensional,machine-readable image. Your wireless device can read the black and white pattern in the square and link its browser directly to a web site. QR Code is a registered trademark of DENSO WAVE INCORPORATED.
69-2718EF—01
64
Regulatory information
FCC Compliance Statement (Part 15.19) (USA only)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause undesired operation.
FCC Warning (Part 15.21) (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b))
(USA only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
65
69-2718EF—01
Regulatory information
Thermostats
To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Section 7.1.2 of RSS-GEN
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Section 7.1.3 of RSS-GEN
Operation is subject to the following two conditions:
1 this device may not cause interference, and
2 this device must accept any interference, including interference that may cause undesired operation of the device.
69-2718EF—01
66
1-year limited warranty
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
(ii) call Honeywell Customer Care at 1-855-733-5465. Customer Care will make the determination whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT
BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER
FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN
55422 or call 1-855-733-5465. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive,
Toronto, Ontario M1V4Z9.
67
69-2718EF—01
Automation and Control Systems
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422 wifithermostat.com
® U.S. Registered Trademark.
Apple, iPhone, iPad, iPod touch and iTunes are trademarks of Apple Inc.
All other trademarks are the property of their respective owners.
© 2012 Honeywell International Inc.
69-2718EF—01 M.S. 08-12
Printed in U.S.A.
69-2718EF-01
Guide de l’utilisateur
Thermostat programmable Wi-Fi
Série RTH6500WF Wi-Fi
Vous trouverez dans la boîte
• Thermostat
• Plaque murale (fixée au thermostat)
• Vis et ancres
• Guide de démarrage rapide
• Carte d’identification de thermostat
• Étiquettes de fils
• Guide de l’utilisateur
• Carte de référence rapide
69-2718EF—01
ii
Bienvenue
Nous vous félicitons de l’achat d’un thermostat programmable Wi-Fi Honeywell. Après vous
être enregistré auprès du service Total Connect
Comfort de Honeywell, vous pouvez surveiller et contrôler à distance le système de chauffage et de refroidissement de votre domicile ou de votre entreprise — vous pouvez rester connecté à votre service confort où que vous soyez.
Le Total Connect Comfort de Honeywell est la solution parfaite si vous voyagez fréquemment, possédez une maison de vacances ou une entreprise ou gérez un immeuble de placement, ou si tout simplement vous recherchez la tranquillité d’esprit.
Ce thermostat fonctionne sur les systèmes de 24 V commun tels que les systèmes à air pulsé, eau chaude, thermopompe, mazout, gaz et électriques.
Il ne fonctionne pas avec les systèmes à mV, tels que les cheminées à gaz, ou avec les systèmes de 120/240 V tels que les chauffages de plinthe.
AVIS RELATIF AU MERCURE : Ne jetez pas l’ancien thermostat dans la poubelle s’il contient du mercure dans un tube scellé. Contactez la Thermostat Recycling
Corporation à l’adresse www.thermostat-recycle.org ou appelez au 1-800-238-8192 pour savoir comment et où mettre au rebut votre thermostat usagé.
AVIS : Pour éviter d’endommager le compresseur, ne faites pas fonctionner le climatiseur si la température extérieure est inférieure à 10 °C (50 °F).
Besoin d’aide?
Consultez le site wifithermostat.com ou appelez au 1-855-733-5465 pour obtenir de l’aide avant de renvoyer le thermostat au magasin.
69-2718EF—01
2
Table des matières
À propos du nouveau thermostat
Aide-mémoire sur les commandes et l’écran d’accueil ...................................... 5
Programmes d’économie d’énergie préconfigurés .............................. 6
Installation
Installation de votre thermostat ................... 8
Connexion à votre réseau Wi-Fi................ 26
Enregistrement de votre thermostat en ligne .................................. 31
Fonctionnement
Setting the time and day ........................... 36
Réglage du ventilateur ............................. 37
Sélection du mode de fonctionnement du système ..................... 38
Réglage des programmes ......................... 39
Dérogation temporaire de la programmation ................................. 40
Dérogation permanente de la programmation ................................. 41
Annulation de l’enregistrement du thermostat ............................................ 42
Déconnexion Wi-Fi .................................... 43
Caractéristiques spéciales ........................ 45
Fonctions et options de configuration ....... 48
Annexes
Questions fréquemment posées ............... 55
Dépannage ................................................ 61
Garantie limitée ......................................... 67
69-2718EF—01
3
Caractéristiques de votre thermostat Wi-Fi
Avec votre nouveau thermostat, vous pouvez :
•
Vous connecter à Internet pour surveiller et contrôler votre système de chauffage/refroidissement
•
Consulter et modifier vos réglages du système de chauffage/refroidissement
•
Consulter et régler la température et les programmes
•
Recevoir des alertes par courrier électronique et obtenir des mises à jour automatiques
Votre nouveau thermostat procure :
•
La technologie Smart Response
•
Une protection du compresseur
•
Une commutation automatique chaud/froid
69-2718EF—01
4
Aide-mémoire sur les commandes et l’écran d’accueil
Une fois votre thermostat Wi-Fi installé, il affichera l’écran d’accueil. Des parties de cet
écran seront modifiées en fonction de la manière dont vous le consultez.
Les messages de
configuration décrivent les étapes du processus de configuration de la Wi-Fi
HOLD
Statut Wi-Fi
Boutons de réglage de la température
Bouton d’annulation permanente
M31586
Régler l’horloge, le jour ou le programme
Sélectionner les paramètres du ventilateur
Sélectionner le mode de fonctionnement du système
Paramètres additionnels
L’écran s’allume lorsque vous appuyez sur un bouton. Il reste allumé pendant 8 secondes après que vous avez apporté les modifications.
Programmes d’économie d’énergie préconfigurés
Ce thermostat contient des programmes d’économie d’énergie préconfigurés pour quatre périodes. L’utilisation des réglages par défaut peut vous permettre de réduire vos dépenses de chauffage/refroidissement jusqu’à 33 % si vous suivez les instructions indiquées. Les
économies peuvent varier en fonction de la région géographique et de l’usage. Pour modifier les réglages, voir pages 39–41.
WAKE (Réveil)
6h
LEAVE (Départ)
8h
RETURN (Retour)
18h
SLEEP (Coucher)
22h
Réglages de chauffage par défaut
70
°
62
°
70
°
62
°
Réglages de refroidissement par défaut
78
°
85
°
78
°
82
°
69-2718EF—01
6
Configuration de votre thermostat
La configuration de votre thermostat programmable Wi-Fi est aisée. Il est préprogrammé et prêt à fonctionner dès qu’il est installé et enregistré.
1
Installez votre thermostat.
2
3
Connectez réseau sans fil de votre domicile.
Enregistrez-vous en ligne pour bénéficier de l’accès à distance.
Avant de commencer,
vous désirerez peut-être visionner une courte vidéo d’installation. Utilisez le QR Code® figurant sur la couverture de ce guide ou consultez le site wifithermostat.com/support
Installation de votre thermostat
Vous aurez besoin des outils suivants pour l’installation de ce thermostat :
• un tournevis Phillips n° 2
• un petit tournevis de poche
• un crayon
• un niveau (optionnel)
• une perceuse et des mèches (3/16 po pour une cloison sèche, 7/32 po pour du plâtre) (optionnel)
• un marteau (optionnel)
• un ruban électrique (optionnel) ou
1 Coupez l’alimentation sur votre système de chauffage/refroidissement.
Important!
Pour protéger votre
équipement, coupez l’alimentation de votre système de chauffage/ refroidissement au niveau du disjoncteur ou du commutateur du système.
Disjoncteur Interrupteur d’alimentation du système de chauffage/ refroidissement
69-2718EF—01
8
Installation de votre thermostat
2 Retirez la plaque de l’ancien thermostat et laissez les fils connectés.
2a Prenez une photo des connexions de câblage pour vous y référer plus tard.
2b Si aucun fil n’est connecté à la borne
C ou si aucune borne C n’est présente sur l’ancien thermostat, visionnez les vidéos expliquant les autres câblages
à wifithermostat.com/videos
Si vous possédez un thermostat plus ancien à tube de mercure scellé, allez à la page 2 pour les instructions de mise au rebut correctes.
C
C
Important!
Le fil C est requis et représente la source d’alimentation principale du thermostat. Sans fil C, votre thermostat ne se mettra pas en marche.
Désignation de la borne
MCR33823
Installation de votre thermostat
3 Étiquetez les fils.
N’appliquez pas les étiquettes en fonction des couleurs des fils.
Utilisez les étiquettes autocollantes fournies pour étiqueter chaque fil lorsque vous le déconnectez. Étiquetez les fils conformément aux désignations de bornes de l’ancien thermostat et non pas en fonction des couleurs des fils.
Remarque :
si aucune étiquette ne correspond à une référence de borne de fil, inscrivez la référence du fil sur une étiquette vierge.
4 Retirez la plaque murale.
Retirez l’ancienne plaque murale du mur après avoir étiqueté et déconnecté tous les fils.
69-2718EF—01
10
C
C
Étiquette autocollante
Étiquette autocollante vierge
MCR31537
Désignation de la borne
Installation de votre thermostat
5 Séparez le thermostat Wi-Fi de sa plaque murale.
Sur votre nouveau thermostat, saisissez les alvéoles du haut et du bas de la plaque murale d’une main et tenez le thermostat (avant) dans l’autre main. Séparez les deux pièces.
Thermostat
PULL HERE
TO REMOVE
Alvéoles
11
PULL HERE
TO REMOVE
Plaque murale
(vue arrière)
M33856
69-2718EF—01
Installation de votre thermostat
6 Montez la plaque murale du thermostat
Wi-Fi.
Montez votre nouvelle plaque murale à l’aide des vis et ancres fournies avec le thermostat.
Au besoin :
Percez des trous de 3/16 po (4,8 mm) pour les cloisons sèches.
Percez des trous de 7/32 po (5,6 mm) pour le plâtre.
Remarque :
Vous pourrez peut-être utiliser les ancres murales déjà installées.
Tenez la plaque murale sur les ancres déjà installées pour vérifier l’alignement.
69-2718EF—01
12
Plaque murale
MCR33857
Installation de votre thermostat
Important!
le fonctionnement du thermostat Wi-Fi requiert l’utilisation d’un fil neutre (C).
Le fil C, ou neutre, amène l’alimentation 24 V ca au thermostat. De nombreux thermostats mécaniques ou à piles plus anciens n’ont pas besoin d’un fil C. Si vous ne disposez pas d’un fil C, essayez :
• de rechercher un fil inutilisé enfoncé dans le mur. Connectez ce fil au fil C et vérifiez s’il est connecté au fil C 24 V ca de votre système de chauffage/refroidissement.
Remarque :
Tous les systèmes de chauffage/refroidissement ne portent pas l’étiquette
24 V c.a. commune « C ». Reportez-vous au manuel sur le système ou communiquez avec le fabricant afin d’identifier la borne 24 V c.a. commune.
Visionnez les vidéos expliquant les autres câblages à wifithermostat.com/videos
Câblage
Pour les systèmes de chauffage/refroidissement
conventionnels
(gaz naturel, appareil de chauffage à mazout ou électrique, climatiseur), voir page 14. Voir « Glossaire » à la page 64 pour des définitions plus complètes.
Pour un système à
thermopompe
, voir page 15. Voir « Glossaire » à la page 64 pour des définitions plus complètes.
13
69-2718EF—01
Installation de votre thermostat
Câblage (système conventionnel)
7A Branchez le thermostat Wi-Fi sur votre système conventionnel.
a En commençant par le fil C, faites correspondre l’étiquette autocollante sur le fil à l’étiquette de la borne.
Vous devez disposer d’un fil neutre (C). Voir page 13.
b Desserrez la vis, insérez le fil dans le bord intérieur de la borne et serrez la vis.
c Vérifiez que le fil est bien attaché en tirant délicatement dessus. d Répétez les étapes a–c pour tous les autres fils.
e Poussez tout excédent de fil dans l’ouverture mural une fois tous les fils installés.
f Poursuivez à la page
20.
Les étiquettes ne correspondent pas?
Reportezvous au code de câblage alternatif des pages 16–17.
K Y2
K L
W2 G W
AUX/E
Retirez le cavalier métallique si les fils
R et RC
deux
G W
G O/B
C
C
C sont tous
présents.
Y
R
Y R RC
Y R RC
CONVENTIONNEL
THERMOPOMPE
Remarque :
Le câblage
MFCR33878 de votre application spécifique peut être différent du câblage illustré ci-avant.
69-2718EF—01
14
Installation de votre thermostat
Câblage (système à thermopompe uniquement)
7B Branchez le thermostat Wi-Fi à votre thermopompe.
a En commençant par le fil C, faites correspondre l’étiquette autocollante sur le fil à l’étiquette de la borne.
Vous devez disposer d’un fil neutre (C). Voir page
13.
b Desserrez la vis, insérez le fil dans le bord intérieur de la borne et serrez la vis.
c Vérifiez que le fil est bien attaché en tirant délicatement dessus. d Répétez les étapes a–c pour tous les autres fils.
e Poussez tout excédent de fil dans l’ouverture mural une fois tous les fils installés.
f Poursuivez à la page 20.
Aux
Les étiquettes ne correspondent pas?
Reportezvous au code de câblage alternatif des pages
18–19.
G O
Y
R
Remarque :
Si l’ancien thermostat est doté de fils distincts aux bornes AUX et E, reliez les deux fils à la borne
E/AUX. Si l’ancien thermostat est doté d’un fil à la borne
AUX et d’un cavalier à la borne E, reliez le fil
à la borne E/AUX. Aucun cavalier n’est requis.
K L AUX/E
G O/B C
Y R RC
THERMOPOMPE
MFCR33877
Remarque :
Le câblage de votre application spécifique peut être
15
Installation de votre thermostat
Câblage alternatif (système conventionnel)
Utilisez ceci si vos étiquettes de fils ne correspondent pas aux références de bornes.
Remarque :
vous devez disposer d’un fil C
(neutre) ou équivalent.
Voir page 13.
Y2 W2 G
ou
F
W
ou
W1
H
C
ou
X
B
C1
Y
ou
Y1
M
2
R
ou
RH
4
V
RC
ou
R
1
K
Y2 W2 G W C
Y R RC
3
CONVENTIONNEL
1
à
3
de la page 17.
69-2718EF—01
16
Installation de votre thermostat
Câblage alternatif (système conventionnel)
1
2
3
N’utilisez pas la borne K. Pour une utilisation ultérieure.
Si votre ancien thermostat est pourvu de deux fils R et RH, retirez le cavalier métallique.
Connectez le fil R à la borne RC et le fil RH à la borne R.
Retirez le cavalier métallique reliant R et RC uniquement si vous devez connecter à la fois R et RC.
17
69-2718EF—01
Installation de votre thermostat
Câblage alternatif (système à thermopompe uniquement)
Utilisez ceci si vos étiquettes de fils ne correspondent pas aux références de bornes.
Remarque :
vous devez disposer d’un fil C (neutre) ou équivalent.
Voir page 13.
L
ou
F
2
E AUX
ou
X
X2
ou
W
W1
W2
G
ou
F
3
4
O
ou
H
B
4
C
ou
X
B
5
Y
ou
Y1
M
6
R
ou
V
VR
RC
ou
R
1
7
K L
AUX/E
G O/B
C Y R RC
THERMOPOMPE
MFCR33886
Reportez-vous aux points
1
à
7
de la page 19.
69-2718EF—01
18
Installation de votre thermostat
Code de câblage alternatif (système à thermopompe uniquement)
1
2
3
4
5
6
7
N’utilisez pas la borne K. Pour une utilisation ultérieure.
Si l’ancien thermostat est doté de fils distincts aux bornes AUX et E, reliez les deux fils à la borne
E/AUX. Si l’ancien thermostat est doté d’un fil à la borne AUX et d’un cavalier à la borne
E, reliez le fil à la borne E/AUX. Aucun cavalier n’est requis.
Si votre ancien thermostat est pourvu d’un fil
O et pas d’un fil B, fixez le fil O à la borne O/B.
Si votre ancien thermostat est pourvu de fils
O et B séparés, fixez le fil B à la borne C. Si un autre fil est relié à la borne C, consultez le site wifithermostat.com pour obtenir de l’aide. Reliez le fil
O à la borne O/B.
Si votre ancien thermostat est pourvu de fils Y1, W1 et W2 consultez le site wifithermostat.com pour obtenir de l’aide.
Si votre ancien thermostat est pourvu de deux fils
V et VR, consultez le site wifithermostat.com pour obtenir de l’aide.
Laissez le cavalier métallique reliant les bornes R et RC en place.
19
69-2718EF—01
Installation de votre thermostat
8 Insérez la carte de référence rapide.
Pliez la carte de référence rapide le long des repères et glissez-la dans la fente à l’arrière du thermostat.
MCR33916
Carte de référence rapide
69-2718EF—01
20
Arrière du thermostat
MCR33858
Installation de votre thermostat
9 Fixez le thermostat à la plaque murale.
Alignez le thermostat sur la plaque murale puis emboîtez-le.
21
HOLD
M33860
69-2718EF—01
Installation de votre thermostat
10 Mettez le système de chauffage/ refroidissement en marche.
Important!
10a Vérifiez que le fil C est branché sur le thermostat et le système de chauffage/refroidissement.
10b Assurez-vous que la porte du système de chauffage/ refroidissement est bien fermée.
10c Rétablissez l’alimentation du système de chauffage/ refroidissement au niveau du disjoncteur ou de l’interrupteur d’alimentation.
69-2718EF—01
22
Disjoncteur ou
Interrupteur
M31544 d’alimentation du système de chauffage/ refroidissement
Installation de votre thermostat
11 Réglez l’horloge à la date et à l’heure courantes.
11a Appuyez sur s
ou t
pour régler l’horloge.
11b Appuyez sur
Set Day
(Régler le jour).
11c Appuyez sur s
ou t
pour sélectionner le jour de la semaine.
11d Appuyez sur
Done
(Terminé) pour enregistrer les réglages.
(Appuyez sans relâcher sur un bouton st
pour modifier rapidement le réglage.)
23
HOLD
MCR33908
HOLD
MCR33909
69-2718EF—01
Installation de votre thermostat
12 Déterminez le type de votre système de chauffage/refroidissement.
Important!
Le type de système de chauffage/refroidissement doit être réglé de sorte que le thermostat fonctionne correctement et n’endommage pas le système.
12a
Si votre système est de type conventionnel à étage unique (étage unique alimenté au gaz naturel avec climatisation), passez à « Connexion à votre réseau
Wi-Fi » à la page 26.
12b
Si le système est de type :
• Chauffage et refroidissement multi-étages conventionnel
• Tout type de thermopompe
• Système à eau chaude
• Autre
Si vous n’êtes pas certain de votre type de système de chauffage/refroidissement ou avez d’autres questions, consultez le site wifithermostat.com/support
Vous DEVEZ changer le type de système en réglant la fonction du système sur 1. Voir la page 48 pour faire correspondre votre thermostat à votre type de système.
69-2718EF—01
24
Installation de votre thermostat
Félicitations! Votre thermostat est maintenant prêt à fonctionner
13 Testez votre thermostat
13a Appuyez sur le bouton
System
pour passer au chauffage ou au refroidissement et mettre l’appareil en marche.
13b Pour accéder à distance à votre thermostat, passez à « Connexion à votre réseau Wi-Fi »
à la page 26.
MCR33880
Le système de chauffage/ refroidissement ne s’allume pas?
Consultez le page 62 ou la
Foire aux questions à wifithermostat.com/support
25
69-2718EF—01
Connexion à votre réseau Wi-Fi
Pour exécuter cette étape, vous devez avoir un appareil sans fil connecté à votre réseau sans fil. Tous ces types d’appareils sont valables :
• Tablette (recommandé)
• Ordinateur portatif (recommandé)
• Téléphone intelligent
Si vous êtes bloqué...
à tout moment dans cette procédure, redémarrez le thermostat en le retirant de la plaque murale, attendez 10 secondes, et emboîtez-le à nouveau sur la plaque murale. Allez à l’étape 1 de cette procédure qui commence à la page 27.
Visionnez la vidéo d’enregistrement au réseau Wi-Fi à wifithermostat.com/videos
69-2718EF—01
26
Connexion à votre réseau Wi-Fi
1 Connectez votre thermostat.
1a Assurez-vous que le thermostat affiche
Wi-Fi
Setup (Configuration Wi-Fi).
1b Sur votre appareil sans fil (tablette, ordinateur portatif, téléphone intelligent), consultez la liste des réseaux sans fil disponibles.
1c Connectez-vous au réseau appelé
NewThermostat_123456 (le chiffre variera).
Remarque :
s’il vous est demandé de spécifier un réseau domestique, publique ou de bureau, sélectionnez Réseau domestique.
27
HOLD
M33852
69-2718EF—01
Connexion à votre réseau Wi-Fi
2 Joignez votre réseau domestique.
2a Ouvrez votre navigateur Web pour accéder à la page de configuration Wi-Fi du thermostat. Le navigateur devrait automatiquement vous diriger vers la page correcte; s’il ne le fait pas, entrez l’adresse http://192.168.1.1
2b Trouvez le nom de votre réseau domestique sur cette page et sélectionnez-le.
Remarque :
Certains routeurs ont des caractéristiques améliorées tels que les réseaux invités; utilisez votre réseau domestique.
2c Suivrez les instructions d’enregistrement à votre réseau Wi-Fi et cliquez sur le bouton Connect
(Connexion). (En fonction de la configuration de votre réseau, vous verrez peut-être une instruction vous demandant d’entrer le mot de passe de votre réseau domestique.)
Remarque :
Si vous n’avez pas correctement branché le thermostat, la page du routeur domestique s’affichera peut-être. Si c’est le cas, revenez à l’étape 1.
69-2718EF—01
28
Connexion à votre réseau Wi-Fi
Remarque :
Si votre réseau Wi-Fi n’apparaît pas dans la liste de la page de configuration Wi-Fi du thermostat :
• Essayez de scanner le réseau à nouveau en appuyant sur le bouton Rescan
(nouveau balayage). Ceci est utile dans les endroits avec plusieurs réseaux.
• Si vous êtes connecté à un réseau invisible, entrez alors le SSID du réseau dans la boîte de dialogue, sélectionnez le type d’encryptage à partir du menu déroulant, et cliquez sur le bouton Add (ajouter). Ceci ajoute manuellement le réseau en tête de la liste. Cliquez sur le nouveau réseau de la liste et entrez le mot de passe si nécessaire. Cliquez sur Connect (connecter) pour joindre le réseau.
29
69-2718EF—01
Connexion à votre réseau Wi-Fi
3 Vérifiez si votre thermostat est connecté.
Lorsque la connexion est en cours,
Wait (Patientez) clignote sur le thermostat pour une durée pouvant aller jusqu’à 3 minutes. Une fois la connexion établie, l’affichage indique
Wi-Fi Setup Connection Success
(Connexion Wi-Fi établie). La puissance du signal Wi-Fi s’affiche dans le coin supérieur droit.
Après environ 60 secondes, l’écran d’accueil s’affiche et Register at Total Connect (Enregistrez-vous sur Total
Connect) clignote jusqu’à ce que l’enregistrement soit terminé.
Si ces messages n’apparaissent pas, voir page 26.
Pour l’enregistrement en ligne de l’accès à distance à
M33875 votre thermostat, poursuivez à la page 31.
Remarque :
Si le thermostat affiche
Connection Failure (Échec de la connexion) ou continue d’afficher
Wi-Fi Setup (Configuration Wi-Fi), confirmez que vous avez correctement entré le mot de passe de votre réseau domestique à l’étape 2. S’il est correct, consultez la Foire aux questions à wifithermostat.com/support
M33876
69-2718EF—01
30
Enregistrement de votre thermostat en ligne
Pour visualiser et régler votre thermostat
Wi-Fi à distance, vous devez posséder un compte Total Connect Comfort. Voici comment procéder.
1 Ouvrez le site web Total Connect Comfort.
Allez sur le site mytotalconnectcomfort.com
Visionnez la vidéo d’enregistrement du thermostat Wi-Fi à wifithermostat.com/videos
31
69-2718EF—01
Enregistrement de votre thermostat en ligne
2 Ouvrez une session ou créez un compte.
Si vous possédez un compte, cliquez sur
Login (Ouvrir une session)
– ou – cliquez sur
Create An Account
(créer un compte).
2a Suivez les instructions à l’écran.
2b
Consultez votre messagerie
et recherchez le message d’activation provenant de My
Total Connect Comfort. Ceci peut prendre plusieurs minutes.
Remarque :
Si vous ne recevez aucune réponse, consultez votre boîte de pourriels ou utilisez une autre adresse électronique.
2c
Suivez les instructions d’activation
figurant dans le message.
2d Ouvrez une session.
69-2718EF—01
32
Enregistrement de votre thermostat en ligne
3 Enregistrez votre thermostat Wi-Fi.
Lorsque vous avez accès à votre compte Total Connect Comfort, enregistrez votre thermostat.
Thermostat ID Card
Use the MAC ID and CRC ID to register this product at mytotalconnectcomfort.com
3a Suivez les instructions à l’écran.
Après avoir ajouté l’emplacement de votre thermostat, vous devez entrer les identifiants uniques de votre thermostat :
• MAC ID
• MAC CRC
Remarque :
Ces identifiants figurent sur la carte d’identification du thermostat fournie dans la boîte du thermostat. Ces identifiants ne sont pas sensibles à la casse.
Carte d’identification de thermostat
Utilisez l’identification MAC et l’identification CRC pour enregistrer ce produit à mytotalconnectcomfort.com
Tarjeta de identificación del termostato
Utilice la identificación MAC y la identificación CRC para inscribir este producto en mytotalconnectcomfort.com
® U.S. Registered Trademark.
© 2012 Honeywell International Inc.
69-2723EFS—01 M.S. 04-12
Printed in U.S.A.
MAC ID
HONEYWELL MODEL:
MAC ID: MAC CRC:
69-2723EFS-01
MAC CRC
33
69-2718EF—01
Enregistrement de votre thermostat en ligne
3b Lorsque le thermostat est convenablement enregistré, l’écran d’enregistrement Total
Connect Comfort affiche le message SUCCESS (réussi).
Sur l’affichage du thermostat,
Setup Complete (Configuration terminée) s’affiche pour environ
90 secondes.
69-2718EF—01
34
Enregistrement de votre thermostat en ligne
3c Veuillez aussi noter que le thermostat affiche maintenant la puissance du signal.
Félicitations! Vous avez terminé.
Vous pouvez maintenant contrôlervotre thermostat de n’importequel endroit au moyen de votre ordinateur portatif, de votre tablette ou de votre téléphone intelligent.
Des applications gratuites sont disponibles pour les appareils iPhone
® iPad
®
et iPod touch
® ou sur Google Play appareils Android.
®
d’Apple
®
pour tous les
,
sur iTunes
®
GET IT ON
35
Download on
iTunes
69-2718EF—01
Réglage de l’heure et du jour
1 Appuyez sur
Set Clock/Day/Schedule
(Régler l’horloge/le jour/le programme), puis sur s
ou sur t
pour régler l’horloge.
2 Appuyez sur
Set Day
(Régler le jour) ou sur s ou sur t
pour choisir le jour de la semaine.
3 Appuyez sur
Done
(Terminé) pour sauvegarder.
Remarque :
Si l’option
Set Clock/Day/Schedule
(Régler l’horloge/le jour/le programme) n’est pas affichée, appuyez sur
Done
(Terminé).
Remarque :
Si
Set Clock (Régler l’horloge) clignote
à l’écran, le thermostat respecte vos réglages pour la période de réveil (WAKE) du lundi jusqu’à ce que vous changiez le réglage de l’heure et du jour.
69-2718EF—01
36
HOLD
HOLD
MCR33855
Réglage du ventilateur
Appuyez
Fan
pour sélectionner
On (en fonction) ou
Auto (basculez pour resélectionner).
Auto : le ventilateur fonctionne uniquement lorsque le système de chauffage ou de refroidissement est en fonction. Auto est le réglage le plus couramment utilisé.
On : le ventilateur est toujours en fonction.
Remarque :
Les options peuvent varier en fonction de l’équipement de chauffage/ refroidissement.
37
MCR33895
69-2718EF—01
Sélection du mode de fonctionnement du système
Appuyez sur
System
(système) pour sélectionner une option.
Heat (chauffage) : commande uniquement le système de chauffage.
Cool (refroidissement) : commande uniquement le système de refroidissement.
Off (arrêt) : les systèmes de chauffage et de refroidissement sont arrêtés.
Auto : sélectionne le chauffage ou le refroidissement en fonction de la température intérieure.
Em Heat (thermopompes avec chauffage auxiliaire) : commande le chauffage auxiliaire/ d’urgence. Le compresseur est arrêt.
MCR33880
Remarque :
Selon la façon dont votre thermostat a été installé, vous pourriez ne pas voir tous les réglages du système.
69-2718EF—01
38
Réglage des programmes
1 Appuyez sur
Set Clock/Day/Schedule
(Régler l’horloge/ le jour/le programme), puis sur
Set Schedule
(Régler le programme).
2 Appuyez sur s
ou sur t
pour régler l’heure du réveil de lundi, puis appuyez sur
Next
(Suivant).
3 Appuyez sur s
ou sur t
pour régler la température pour cette période, puis appuyez sur
Next
(Suivant).
4 Réglez l’heure et la température pour la période suivante (Leave/Départ). Répétez les étapes 2 et 3 pour chaque période.
5 Appuyez sur
Next
(Suivant) pour régler les périodes du jour suivant. Répétez les étapes 2 à 4 pour chaque jour.
6 Appuyez sur
Done
(Terminé) pour sauvegarder et quitter.
Remarque :
Assurez-vous que le thermostat est réglé au mode de système que vous souhaitez programmer [Heat
MCR33892
69-2718EF—01
Dérogation temporaire de la programmation
Appuyez sur s
ou t
pour ajuster immédiatement la température.
La nouvelle température sera uniquement maintenue jusqu’au début de la prochaine période programmée.
Pour annuler ce réglage temporaire à tout moment, appuyez sur
Cancel
(annuler).
L’horaire de programmation est à nouveau en vigueur.
HOLD
MCR33896
69-2718EF—01
40
Dérogation permanente de la programmation
1 Appuyez sur
HOLD
(maintien) pour régler la température de façon permanente. Ceci désactive l’horaire de programmation.
2 Appuyez sur s
ou sur t
pour régler la température. Le réglage de la température sera maintenu 24 heures par jour jusqu’à ce que vous le changiez manuellement ou que vous appuyiez sur
Cancel
(Annuler) pour revenir au programme.
HOLD
MCR33897
41
69-2718EF—01
Annulation de l’enregistrement du thermostat
Si vous supprimez le thermostat de votre compte Total Connect Comfort (par exemple, si vous déménagez et laissez le thermostat en place), le thermostat affichera le message
Register at Total Connect
(Enregistrez-vous sur Total Connect) jusqu’à ce qu’il soit enregistré de nouveau.
M33876
69-2718EF—01
42
Déconnexion Wi-Fi
Remplacement du routeur
Si vous déconnectez le thermostat de votre réseau Wi-Fi :
1 Entrez dans la configuration du système (voir page 48).
2 Réglez la fonction 39 à 0 (voir page 54).
L’écran affichera le message
Wi-Fi Setup (Configuration
Wi-Fi).
Reconnectez-vous à un réseau Wi-Fi en suivant les étapes de la page 26.
M33855
Désactivation de la Wi-Fi
Si vous ne prévoyez pas contrôler le thermostat à distance, vous pouvez supprimer le message Wi-Fi Setup (Configuration Wi-Fi) de l’écran :
1 Accédez à la configuration du système (voir page 48).
2 Changez le paramètre 38 à 0 (voir page 54). La mention Wi-Fi Setup sera supprimée de l’écran. Si vous voulez connecter le réseau Wi-Fi plus tard, remettez le paramètre 38 à 1.
43
69-2718EF—01
Mises à jour du logiciel
Honeywell introduit régulièrement des mises à jour du logiciel pour ce thermostat. Les mises à jour s’effectuent automatiquement par votre connexion Wi-Fi. Tous vos réglages sont sauvegardés; vous n’avez donc pas besoin de procéder à des changements après la mise à jour.
Pendant la mise à jour, le message
Updating (Mise à jour en cours) clignote sur votre thermostat qui affiche
également le pourcentage de mise à jour effectué.
Lorsque la mise à jour est terminée, votre écran d’accueil reprend son apparence habituelle.
Remarque :
Si le thermostat n’est pas connecté
à la Wi-Fi, vous n’obtiendrez pas les mises à jour automatiques.
69-2718EF—01
44
M34001
Pourcentage de mise à jour terminé
Technologie Smart Response
Celle-ci permet au thermostat « d’apprendre » combien de temps il faut à votre système de chauffage/refroidissement pour atteindre le réglage de température programmé, afin que la température voulue soit obtenue à l’heure programmée.
Par exemple : réglez l’heure de réveil à 6 heures et la température à 70°. Le chauffage est mis en fonction avant 6 heures de manière
à ce que la température soit de 70° à 6 heures.
Remarque :
la fonction de configuration système 13 contrôle la technologie Smart
Response. Voir « Technologie Smart
Response » à la page 52.
M33881
Le message
Recovery (reprise) s’affiche lorsque le système est activé avant une période de temps programmée.
45
69-2718EF—01
Protection du compresseur
Cette fonction force le compresseur à attendre quelques minutes avant un redémarrage, pour
éviter d’endommager l’équipement.
69-2718EF—01
46
M33882
Le message
Cool On
(Refroidissement en marche) (ou Heat On
[Chauffage en marche] pour une pompe à chaleur) clignote en attendant.
Commutation automatique
Celle-ci est utilisée dans les climats où le conditionnement d’air et le chauffage sont utilisés le même jour.
Lorsque le système est réglé sur
Auto, le thermostat sélectionne automatiquement le chauffage ou le refroidissement en fonction de la température intérieure.
L’écart entre les réglages de chauffage et de refroidissement doit être d’au moins 3 degrés. Le thermostat ajuste automatiquement les réglages afin de maintenir ces 3 degrés d’écart.
Remarque :
la fonction de configuration système
12 contrôle la commutation automatique. Voir
« Commutation manuelle/automatique » à la page 52.
47
MCR33893
69-2718EF—01
Fonctions et options de configuration
Vous pouvez modifier des options pour plusieurs fonctions du système. Les fonctions disponibles dépendent de votre type de système. Les fonctions ainsi que les options disponibles sont décrites aux pages 50–54.
Ce thermostat est préréglé pour un système de chauffage/refroidissement à étage unique. La fonction de configuration 1 pour une thermopompe ajustera les réglages par défaut.
69-2718EF—01
48
Fonctions et options de configuration
1 Appuyez simultanément sur
Fan
(Ventilateur) et sur s
pendant 3 secondes environ. L’écran change pour afficher deux nombres et les appellations des boutons sont les suivantes :
Done (Terminé), Back (Retour), sans appellation,
Next (Suivant).
2 Appuyez sur
Next
(Suivant) jusqu’à ce que vous aperceviez le numéro de la fonction – le nombre plus élevé à gauche – du réglage voulu.
3 Pour modifier les options d’une fonction, appuyez sur s
ou sur t
jusqu’à ce que l’option voulue (le nombre plus petit à droite) s’affiche.
4 Répétez les étapes 2 et 3 jusqu’à ce que vous ayez réglé toutes les fonctions que vous souhaitez modifier.
5 Lorsque toutes les modifications ont été effectuées, appuyez sur
Done
(Terminé) pour
HOLD
MCR33883
HOLD
MCR33884
69-2718EF—01
Configuration du système
1
(Voir la page 48 pour les instructions.)
Fonction
Sélection du type de système
Si vous n’êtes pas certain de votre type de système de chauffage/ refroidissement ou que vous avez d’autres questions, consultez le site wifithermostat.com
Réglages et Options
0 Chauffage/refroidissement : chauffage au gaz, au mazout ou électrique avec climatisation centrale.
1
Thermopompe : thermopompe sans chauffage de secours ou auxiliaire.
2 Chauffage uniquement : chauffage au gaz, au mazout ou à l’eau chaude sans climatisation centrale.
3 Chauffage uniquement avec ventilateur : chauffage au gaz, au mazout ou électrique sans climatisation centrale.
4 Refroidissement uniquement : climatisation centrale uniquement.
5 Thermopompe : thermopompe avec chauffage de secours ou auxiliaire.
6 Chauffage/refroidissement multi-étages : 2 étages de chauffage (fils sur
W et W2), 2 étages de refroidissement (fils sur Y et Y2).
7 Chauffage/refroidissement multi-étages : 2 étages de chauffage (fils sur W et W2), 1 étage de refroidissement (fils sur Y).
8
Chauffage/refroidissement multi-étages : 1 étage de chauffage (fils sur
W), 2 étages de refroidissement (fils sur Y et Y2).
69-2718EF—01
50
Configuration du système
(Voir la page 48 pour les instructions.)
Fonction Réglages et Options
2
Vanne de commutation de thermopompe
(pour thermopompes uniquement)
0 Vanne de commutation de refroidissement : utilisez ce réglage si vous avez connecté un fil étiqueté « O » à la borne O/B.
1 Vanne de commutation de chauffage : utilisez ce réglage si vous avez connecté un fil étiqueté « B » à la borne O/B.
3
Commande du ventilateur de chauffage
0 Chauffage au gaz ou au mazout : utilisez ce réglage en cas de système de chauffage au gaz ou au mazout (le système contrôle le fonctionnement du ventilateur).
1
Chauffage électrique : utilisez ce réglage en cas de système de chauffage
électrique (le thermostat contrôle le fonctionnement du ventilateur).
5
Cycle de chauffage
5
Appareil de chauffage au gaz ou au mazout : appareil de chauffage au
6
Cycle de chauffage,
étape 2
gaz/mazout standard (rendement inférieur à 90 %).
9
Appareil de chauffage électrique : systèmes de chauffage électriques.
3
Appareil de chauffage à eau chaude ou à haut rendement : système à eau chaude ou appareil de chauffage au gaz (rendement supérieur à 90 %).
1
Système à vapeur ou à gravité au gaz/mazout : systèmes de chauffage à vapeur ou à gravité.
51
69-2718EF—01
Configuration du système
(Voir la page 48 pour les instructions.)
Fonction Réglages et Options
12
Commutation manuelle/automatique
Voir la page 47 pour de plus amples informations.
0 Commutation manuelle (Chauffage/Refroidissement/Arrêt).
1 Commutation automatique (Chauffage/Refroidissement/Auto/Arrêt). Active automatiquement le chauffage ou le refroidissement en fonction de la température de la pièce. Remarque : le système maintient une différence minimale de 3 °F entre les réglages de chaleur et de refroidissement.
13
Technologie Smart
Response
Voir la page 45 pour de plus amples informations.
1 En marche
0 Arrêt
14
Unité de température (°F/°C)
0 Fahrenheit
1 Celsius
16
Options de programmation
1 Horaire de programmation activé (programmable sur 7 jours).
0 Horaire de programmation désactivé. Le thermostat ne peut pas être programmé.
69-2718EF—01
52
Configuration du système
(Voir la page 48 pour les instructions.)
Fonction Réglages et Options
36
Device Name
(Nom de l’appareil)
Ce nom identifiera le thermostat lorsque vous le consultez à distance.
Si vous enregistrez plusieurs thermostats, attribuez un nom différent à chacun d’entre eux.
52 = Thermostat
1 Basement
2 Bathroom
3 Bathroom 1
4 Bathroom 2
5 Bathroom 3
6 Bedroom
7 Bedroom 1
8 Bedroom 2
9 Bedroom 3
10 Bedroom 4
11 Boat House
12 Bonus Room
13 Computer Room 28 Kitchen 2
14 Den
15 Dining Room
16 Exercise Room 30 Library 44 Porch
17 Family Room 31 Living Room 45 Rec Room
18 Fireplace
19 Foyer
20 Game Room
21 Garage
22 Great Room
23 Guest Room
24 Gym
25 Kid's Room
26 Kitchen
27 Kitchen 1
32 Lower Level 46 Sewing Room
33 Master Bath 47 Spa
34 Master Bed 48 Storage Room
35 Media Room 49 Studio
36 Music Room 50 Sun Room
37 Nursery
38 Office
39 Office 1
40 Office 2
41 Pantry
51 Theater
52 Thermostat
53
54
55
Upper Level
Utility Room
Walk In Closet
42 Play Room 56 Wine Cellar
29 Laundry Room 43 Pool Room 57 Workshop
53
69-2718EF—01
Configuration du système
(Voir la page 48 pour les instructions.)
Fonction Réglages et Options
38
Wi-Fi
En marche/Arrêt
1 Le Wi-Fi est en marche et le thermostat peut être connecté à un réseau Wi-Fi
0 Le Wi-Fi est en marche. Le thermostat ne peut pas être connecté à un réseau Wi-Fi. Si vous ne connectez pas le thermostat à un réseau Wi-Fi, le texte
Wi-Fi Setup (configuration Wi-Fi) sera supprimé de la fenêtre de messages.
39
Connexion Wi-Fi
1 Connecté au réseau Wi-Fi. Il s’agit de la configuration automatique lorsque le thermostat est connecté au réseau Wi-Fi.
0 Sélectionnez 0 pour le déconnecter du réseau Wi-Fi.
42
Affichage de la période et du jour de la semaine
0 La période et le jour ne sont pas affichés à l’écran d’accueil.
1 La période et le jour sont affichés à l’écran d’accueil.
85
Restaurer la programmation par défaut
0 Continuer à utiliser l’horaire programmé.
1 Restaurer le programme du thermostat aux réglages d’économie d’énergie
90
Restauration des réglages originaux
0 Non
1 Déconnecte le thermostat du réseau Wi-Fi et restaure les réglages d’origine (efface les personnalisations).
69-2718EF—01
54
Questions fréquemment posées
Q : Mon thermostat fonctionnera-t-il toujours si je perds ma connexion Wi-Fi?
R
:
Oui, le thermostat actionnera votre système de chauffage et/ou de refroidissement avec ou sans
Wi-Fi.
Q : Comment puis-je trouver le mot de passe de mon routeur?
R
:
Contactez le fabricant du routeur.
Q : Pourquoi ne vois-je pas ma page de configuration Wi-Fi?
R
:
Vous êtes probablement uniquement connecté à votre routeur, et non pas à votre thermostat.
Essayez de vous reconnecter au thermostat.
Q : Pourquoi mon thermostat ne se connecte-t-il pas à mon routeur Wi-Fi même si celui-ci est très proche du thermostat?
R
:
Vérifiez si le mot de passe saisi pour le routeur Wi-Fi est correct.
55
69-2718EF—01
Questions fréquemment posées
Q : Où puis-je trouver mes codes MAC ID et MAC CRC?
R
:
Les numéros MAC ID et MAC CRC figurent sur la carte qui accompagne le thermostat ou au dos du thermostat (visible lorsque le thermostat est retiré de la plaque murale). Chaque thermostat possède un MAC ID et un MAC CRC uniques.
Q : Il est impossible d’enregistrer mon thermostat sur le site Total Connect Comfort.
R
:
Vérifiez si le thermostat est correctement inscrit dans le réseau Wi-Fi domestique. La fenêtre de messages affichera
Wi-Fi Setup ou Register at Total Connect. Vous devriez également voir l’icône de force de signal Wi-Fi. Vérifiez si le routeur Wi-Fi dispose d’une bonne connexion internet. Sur votre ordinateur, vérifiez si vous pouvez ouvrir la page mytotalconnectcomfort.com
Si vous ne pouvez pas l’ouvrir, coupez votre modem internet pendant quelques secondes, puis rallumez-le.
69-2718EF—01
56
Questions fréquemment posées
Q : Je suis enregistré sur le site Total Connect Comfort mais je n’ai pas pu ouvrir de session en utilisant mon nouveau compte.
R
:
Consultez votre messagerie et vérifiez si vous avez reçu le message d’activation. Suivez les instructions d’activation de votre compte, puis ouvrez une session sur le site web.
Q : Je me suis enregistré sur le site Total Connect Comfort et n’ai pas reçu de message de
: confirmation.
R Vérifiez si le message ne se trouve pas dans le dossier des spams ou des messages effacés.
Q : Y a-t-il un moyen d’accroître la force du signal?
R
:
La plupart des routeurs peuvent être configurés comme répéteur. Vous pouvez également acheter et installer un répéteur Wi-Fi.
Pour plus de questions fréquemment posées, consultez le site wifithermostat.com/support
57
69-2718EF—01
Dépannage
Perte du signal
Si l’indicateur no-Wi-Fi (pas de Wi-Fi) s’affiche à la place de l’indicateur de puissance du signal Wi-Fi dans le coin supérieur droit de l’écran d’accueil :
• Assurez-vous que la Wi-Fi fonctionne chez vous en la vérifiant sur un autre appareil; si elle ne fonctionne pas, adressez-vous à votre fournisseur de services Internet.
• Déplacez le routeur.
• Redémarrez le thermostat : retirez-le de la plaque murale, patientez pendant 10 secondes et raccrochez-le sur la plaque murale. Revenez à l’étape 1 de la section Connexion à votre réseau
Wi-Fi.
69-2718EF—01
58
Dépannage
Codes d’erreur
Dans le cas de certains problèmes, l’écran du thermostat affiche un code qui désigne la nature du problème. Tout d’abord, les codes d’erreur sont affichés seuls dans la zone de l’heure de l’écran; après quelques minutes, l’écran d’accueil s’affiche et le code et l’heure s’affichent alternativement.
M33999
Code d’erreur Action
E01
L’alimentation du routeur a été coupée pendant la configuration de la Wi-Fi.
• Assurez-vous que le routeur est alimenté.
• Si vous essayez d’établir la connexion à un réseau masqué ou ajouté manuellement, assurez-vous que le routeur est alimenté et fonctionne.
E02
Mot de passe Wi-Fi non valide.
Ce code s’affiche pendant 30 secondes, puis le thermostat se remet en mode Wi-Fi Setup
(Configuration de la Wi-Fi).
• Saisissez de nouveau le mot de passe du réseau Wi-Fi de votre maison.
• Répétez le processus de configuration et confirmez le mot de passe du réseau Wi-Fi de votre maison.
59
69-2718EF—01
Dépannage
Code d’erreur Action
E42
Le routeur ne fournit pas d’adresse IP au thermostat.
• Patientez pendant 30 minutes, la connexion peut prendre plusieurs minutes.
• S’il n’y a toujours pas de connexion, retirez le thermostat de la plaque murale pendant 10 secondes, puis raccrochez-le
(voir page 26).
• Assurez-vous que votre routeur est correctement configuré pour fournir automatiquement les adresses IP.
E43
Pas de connexion Internet. Le thermostat ne peut pas communiquer avec Total Connect
Comfort.
• Assurez-vous que le câble Internet est branché.
• Redémarrez le routeur.
E99
Erreur d’ordre général Retirez le thermostat de la plaque murale pendant 10 secondes, puis raccrochez-le
(voir page 26).
69-2718EF—01
60
M33998
Dépannage
En cas de difficultés avec le thermostat, essayer les suggestions suivantes.
La plupart des problèmes peuvent être réglés rapidement et facilement.
Rien n’apparaît à l’écran
• Vérifiez le disjoncteur et réinitialisez-le si nécessaire.
• Assurez-vous que l’interrupteur de marche-arrêt du système de chauffage et de refroidissement est sur marche.
• Assurez-vous que la porte de l’appareil de chauffage est bien fermée.
• Vérifiez si le fil C est connecté (voir page 13).
• Vérifiez la fonction 1 : Type de système pour vous assurer qu’elle soit configurée en fonction de votre équipement de chauffage et de refroidissement (voir page 50).
Impossible de changer le réglage du système
à Refroidissement
Le ventilateur ne tourne pas lorsque de la chaleur est requise
Les mentions
Cool On
(Refroidissement en marche) ou
Heat On
(Chauffage en marche) clignotent à l’écran.
• Vérifiez la fonction 3 : Commande du ventilateur de chauffage pour vous assurer qu’elle soit configurée en fonction de votre équipement de chauffage (voir page 51).
• La fonction de protection du compresseur est activée. Attendez 5 minutes que le système se remette en marche en toute sécurité sans endommager le compresseur.
61
69-2718EF—01
Dépannage
La thermopompe
émet de l’air frais en mode chauffage, ou de l’air chaud en mode refroidissement
Le système de chauffage ou de refroidissement ne répond pas
• Vérifiez la fonction 2 : Vanne de commutation de thermopompe pour vous assurer qu’elle soit configurée en fonction de votre équipement de chauffage (voir page 51).
• Appuyez sur
System
(système) pour régler le système sur Heat
(chauffage). Vérifiez si le réglage de température est supérieur à la température intérieure.
• Appuyez sur
System
pour régler le système sur Cool
(refroidissement). Vérifiez si le réglage de température est inférieur à la température intérieure.
• Vérifiez le disjoncteur et réinitialisez-le si nécessaire.
• Assurez-vous que l’interrupteur de marche-arrêt du système de chauffage et de refroidissement est sur marche.
• Assurez-vous que la porte de l’appareil de chauffage est bien fermée.
• Attendez 5 minutes que le système réponde.
69-2718EF—01
62
Dépannage
Le système de chauffage fonctionne en mode refroidissement
L’équipement de chauffage et l’équipement de refroidissement fonctionnent en même temps
• Vérifiez la fonction 1 : Type de système pour vous assurer qu’elle soit configurée en fonction de votre équipement de chauffage et de refroidissement (voir page 50).
• Vérifiez la fonction 1 : Type de système pour vous assurer qu’elle soit configurée en fonction de votre équipement de chauffage et de refroidissement (voir page 50).
• Saisissez et retirez le thermostat de la plaque murale. Assurez-vous qu’aucun fils dénudés ne se contactent.
• Vérifiez si le câblage du thermostat est adéquat.
63
69-2718EF—01
Glossaire
Fil C
Le fil « C », ou neutre, amène l’alimentation 24 V ca au thermostat à partir du système de chauffage/ refroidissement. Certains anciens thermostats mécaniques ou à pile peuvent ne pas être dotés de ce fil. Il est nécessaire à l’établissement d’une connexion Wi-Fi à votre réseau domestique.
Système de chauffage/refroidissement à thermopompe
Des thermopompes sont utilisées pour chauffer et refroidir un immeuble. Si votre ancien thermostat comporte un réglage pour chauffage auxiliaire ou d’urgence, vous avez probablement une thermopompe.
Système de chauffage/refroidissement conventionnel
Systèmes sans thermopompe ; ceux-ci incluent des appareils de traitement d’air, des appareils de chauffage ou des chaudières qui fonctionnent au gaz naturel, au mazout ou à l’électricité. Ils peuvent ou non inclure un appareil de conditionnement d’air.
Cavalier
Un petit morceau de fil reliant deux bornes ensemble.
MAC ID, MAC CRC
Codes alphanumériques identifiant de manière unique votre thermostat.
QR Code
®
Code de réponse rapide. Une image bidimensionnelle lisible par une machine. Votre appareil sans fil peut lire le motif noir et blanc inséré dans le carré et connecter directement son navigateur à un site web. QR Code est une marque déposée de DENSO WAVE INCORPORATED.
69-2718EF—01
64
Informations réglementaires
Déclaration de conformité à la FCC (partie 15.19)
(États-Unis uniquement)
Cet appareil est conforme à la partie 15 du règlement de la FCC. Son fonctionnement est soumis aux deux conditions suivantes :
1 Ce dispositif ne doit pas causer d’interférences nuisibles, et
2 Ce dispositif doit accepter toutes les interférences reçues, y compris celles pouvant causer un fonctionnement non souhaité.
Avertissement de la FCC (partie 15.21) (États-Unis uniquement)
Toute modification qui n’est pas autorisée expressément par la partie responsable de la conformité de l’appareil peut rendre l’utilisateur inapte à faire fonctionner l’équipement.
sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère, utilise et peut
émettre de l’énergie de radiofréquence, et s’il n’est pas installé et utilisé conformément aux instructions, peut causer des interférences nuisibles aux communications radio. Il n’y a toutefois aucune garantie qu’une interférence ne se produira pas dans une installation particulière. Si cet équipement cause des interférences nuisibles à la réception radio et télévision, ce qui peut être déterminé en éteignant le dispositif et en le remettant en marche, il est recommandé à l’utilisateur de tenter de corriger l’interférence par l’une des mesures suivantes :
• Réorienter ou déplacer l’antenne réceptrice.
• Augmenter la séparation entre l’équipement et le récepteur.
Déclaration relative aux interférences de la FCC
(partie 15.105 (b)) (États-Unis uniquement)
• Brancher l’équipement dans la prise d’un circuit différent de celui auquel le récepteur est connecté.
Cet équipement a été testé et est conforme aux limites des dispositifs numériques de Classe B, conformément
• Consulter le distributeur ou un technicien radio/TV compétent pour obtenir de l’aide.
à la Partie 15 du règlement de la FCC. Ces limites
65
69-2718EF—01
Informations réglementaires
Thermostats
Pour être conformes aux limites d’exposition aux radiofréquences établies par FCC et Industrie Canada pour le grand public/l’exposition non contrôlée, la ou les antennes utilisées pour ces transmetteurs doivent être installées à au moins 20 cm de toutes les personnes et ne peuvent être situées au même endroit qu’une autre antenne ou fonctionner conjointement avec une autre antenne ou un autre transmetteur.
Section 7.1.2 de RSS-GEN
Conformément aux normes d’Industrie Canada, ce transmetteur radio ne peut fonctionner qu’avec une antenne dont le type et le gain maximum sont approuvés par Industrie Canada. Pour réduire les risques d’interférence s radio encourus par d’autres utilisateurs, le type et le gain de l’antenne doivent
être choisis de façon à ce que la puissance rayonnée isotrope équivalente (p.i.r.e.) ne soit pas supérieure
à celle nécessaire à l’établissement d’une bonne communication.
Section 7.1.3 de RSS-GEN
Le fonctionnement est soumis aux deux conditions suivantes :
1 Ce dispositif ne doit pas causer d’interférences, et
2 Ce dispositif doit accepter toutes les interférences, y compris celles pouvant causer un fonctionnement non souhaité.
69-2718EF—01
66
Garantie limitée d’un an
Honeywell garantit ce produit, à l’exception des piles, contre tout défaut de pièce ou de main-d’œuvre, durant une période d’un (1) an
à partir de la date d’achat par le consommateur si le produit est utilisé et entretenu convenablement. En cas de défectuosité ou de mauvais fonctionnement pendant la période de garantie, Honeywell remplacera ou réparera le produit, à sa discrétion.
Si le produit est défectueux,
(i) le renvoyer avec la facture ou une autre preuve d’achat date au lieu d’achat; ou
(ii) appeler le service à la clientèle de Honeywell en composant le 1-855-733-5465. Le service à la clientèle déterminera si le produit doit être retourné à l’adresse suivante : Honeywell Return Goods, Dock 4MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, ou si un produit de remplacement peut vous être expédié.
La présente garantie ne couvre pas les frais de retrait ou de réinstallation. La présente garantie ne s’appliquera pas s’il est démontré par Honeywell que la défectuosité ou le mauvais fonctionnement sont dus à un endommagement du produit alors que le consommateur l’avait en sa possession.
La responsabilité exclusive de Honeywell se limite à réparer ou à remplacer le produit conformément aux modalités susmentionnées.
HONEYWELL N’EST EN AUCUN CAS RESPONSABLE DES PERTES OU DOMMAGES, Y COMPRIS LES DOMMAGES INDIRECTS
OU ACCESSOIRES DÉCOULANT DIRECTEMENT OU INDIRECTEMENT D’UNE VIOLATION QUELCONQUE D’UNE GARANTIE,
EXPRESSE OU TACITE, APPLICABLE AU PRÉSENT PRODUIT, OU TOUTE AUTRE DÉFECTUOSITÉ DU PRÉSENT PRODUIT.
Certaines provinces ne permettent pas l’exclusion ou la restriction des dommages indirects ou accessoires et, par conséquent, la présente restriction peut ne pas s’appliquer.
CETTE GARANTIE EST LA SEULE GARANTIE EXPRESSE FAITE PAR HONEYWELL POUR CE PRODUIT. LA DURÉE DE TOUTE
GARANTIE IMPLICITE, INCLUANT LES GARANTIES DE QUALITÉ MARCHANDE OU D’ADAPTATION À UNE UTILISATION
PARTICULIÈRE, EST LIMITÉE PAR LES PRÉSENTES À LA PÉRIODE D’UNE ANNÉE DE LA PRÉSENTE GARANTIE. Certaines provinces ne permettent pas de limiter la durée des garanties tacites et, par conséquent, la présente limitation peut ne pas s’appliquer.
La présente garantie donne au consommateur des droits spécifiques et certains autres droits qui peuvent varier d’une province à l’autre.
Pour toute question concernant la présente garantie, prière d’écrire aux Services à la clientèle de Honeywell à l’adresse suivante :
Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 ou composer le 1-855-733-5465. Au Canada, prière de s’adresser à Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Toronto, Ontario M1V4Z9.
67
69-2718EF—01
Systèmes d’automatisation et de régulation
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422 wifithermostat.com
® Marque de commerce déposée américaine.
Apple, iPhone, iPad, iPod touch et iTunes sont des marques de commerce de Apple Inc.
Toutes les autres marques de commerce sont propriété de leurs propriétaires respectifs.
© 2012 Honeywell International Inc.
69-2718EF—01 M.S. 08-12
Imprimé aux États-Unis
69-2718EF-01
advertisement
Key Features
- Remote access and control via the Internet
- Smart Response Technology learns your heating and cooling patterns
- Compressor protection helps to prevent damage to your air conditioner
- Programmable with up to four different temperature settings per day
- Can be set to automatically switch between heating and cooling modes
- Permanent override button allows you to temporarily override the programmed settings
Related manuals
Frequently Answers and Questions
How do I connect the thermostat to my Wi-Fi network?
How do I register my thermostat online?
How do I set the time and day on the thermostat?
How do I set the fan settings on the thermostat?
How do I select the system mode on the thermostat?
How do I adjust the program schedules on the thermostat?
How do I override the schedules temporarily on the thermostat?
advertisement
Table of contents
- 7 quick reference
- 8 Preset energy-saving schedules
- 10 Installing your thermostat
- 28 Connecting to your Wi-Fi network
- 33 Registering your thermostat online
- 38 Setting the the time and day
- 39 Setting the fan
- 40 Selecting system mode
- 41 Adjusting program schedules
- 42 Overriding schedules temporarily
- 43 Overriding schedules permanently
- 44 Unregistering thermostat
- 45 Disconnecting Wi-Fi
- 47 Special features
- 50 Setting functions and options
- 57 Frequently asked questions
- 63 Troubleshooting
- 69 Limited warranty
- 77 et l’écran d’accueil
- 78 d’énergie préconfigurés
- 80 Installation de votre thermostat
- 98 Connexion à votre réseau Wi-Fi
- 103 thermostat en ligne
- 108 Setting the time and day
- 109 Réglage du ventilateur
- 110 fonctionnement du système
- 111 Réglage des programmes
- 112 de la programmation
- 114 du thermostat
- 115 Déconnexion Wi-Fi
- 117 Caractéristiques spéciales
- 120 Fonctions et options de configuration
- 127 Questions fréquemment posées
- 133 Dépannage
- 139 Garantie limitée