advertisement
Yamaha Professional Audio CL StageMix V4.5 User Guide
5.2.1 HPF
When any input channel is selected in the EQ Editing Screen, an [HPF] button appears at the top of the EQ graph. Press this button to switch the HPF on/off. When the button is green, the HPF is On. HPF has no
Gain or Q parameter: only frequency.
The Slope of an Input Channel’s HPF can be adjusted between -6dB and -12dB per octave by pressing the buttons in the floating display above the HP dot.
Note: this feature requires CL console firmware V1.5 or higher.
When an output channel is selected in the EQ Editing Screen, the
[HPF] button will only appear if band 1 is assigned to the HPF function.
5.2.2 EQ Bands 1 & 4
EQ bands 1 & 4 have additional choices of band-type. Both these bands can be assigned to function as a shelf or a bell, and band 4 can also function as a Low Pass Filter. Band 1 can also be a HPF for Mix,
Matrix and Stereo/Mono Master channels. When one of these bands is selected, the relevant additional buttons are shown above the EQ graph.
5.2.3 EQ ON
The channel EQ can be switched on/off with the [EQ ON] button towards the top-right of the EQ screen. It is green when the EQ is on.
When the EQ is switched off, the EQ curve will be grey.
5.2.4 EQ RESET
The [RESET] button above the EQ curve allows the EQ to be reset to either its Default values or to Flat. After pressing [RESET], an “Are You
Sure?” popup will be displayed before the action is executed.
• Selecting “Default EQ” will reset all EQ parameters for the selected channel back to their default values, including HPF.
• Selecting “Flatten EQ” will set the Gain of bands 1-4 to 0dB, but will not change the Q and Frequency values.
• Select “No” to cancel and exit this function.
Page 27
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 System Requirements
- 5 Wi-Fi Settings
- 6 Getting Started
- 6 CL series Network Setup
- 6 iPad Wi-Fi Settings
- 6 Using DHCP
- 7 Using a Static IP Address
- 8 StageMix Setup
- 9 OFFLINE DEMO
- 9 Configure StageMix to Work with a CL series Console
- 10 Select a Mixer and Begin Working
- 11 Edit Mixer Configurations
- 12 Mixer Window
- 12 Channel Bank Navigation
- 12 Layer Navigation
- 12 Channel Names and Colors
- 13 Faders
- 13 Long Faders
- 13 Navigation in Long Faders Mode
- 14 Channel ON
- 15 Master Bank
- 17 Digital Gain
- 17 Gain Compensation Mode
- 17 Analog Gain / Digital Gain Link
- 17 ALL GC ON
- 17 ALL GC OFF
- 17 Input Port
- 18 Phantom Power
- 18 Phase
- 19 SENDS ON FADERS
- 20 Mix Send Levels
- 20 Mix Sends ON
- 20 Mix Send PRE/POST
- 21 Global PRE/POST
- 21 Stereo Mix Pan
- 22 DCA FADERS
- 23 EQ / PAN / DYNAMICS
- 23 EQ Curve in Mixer Window
- 24 Selecting PEQ or GEQ
- 24 Accessing the EQ Editing Screens
- 25 PARAMETRIC EQ EDITING
- 27 EQ Bands
- 27 EQ ON
- 27 EQ RESET
- 28 EQ TYPE
- 28 PEQ COPY/PASTE
- 29 GRAPHIC EQ EDITING
- 29 Navigation in the GEQ Overview Section
- 29 Rack Position
- 30 GEQ Type
- 30 Insert Position
- 30 Editing GEQ Bands
- 30 Navigation in the GEQ Editing Section
- 30 GEQ ON
- 30 GEQ FLAT
- 30 GEQ Copy/Paste
- 31 PAN TO STEREO BUSSES
- 31 Balance
- 32 DYNAMICS PROCESSORS
- 33 DYNAMICS PROCESSOR EDITING
- 33 Default
- 33 Copy/Paste
- 34 Dynamics On
- 34 Dynamics Type
- 34 Threshold
- 34 Range and Ratio
- 34 Other Dynamics Parameters
- 35 Key In
- 36 OUTPORTS
- 36 Navigation
- 36 Output Port Identification
- 37 Delay On
- 37 Delay Time Display
- 37 Output Port Phase
- 37 Output Port Gain
- 37 Delay Time Editor
- 38 Delay Scale
- 38 Numeric Keypad
- 38 Nudge Delay Time Values
- 38 Copy Delay Time Value
- 39 Paste Delay Time Value
- 39 Close the Delay Time Editor
- 40 UTILITY
- 40 MUTE GROUP MASTERS
- 41 Mute Group Dim Level
- 43 TAP TEMPO
- 43 Multi-Select
- 44 OSCILLATOR
- 44 Oscillator Assign
- 44 Oscillator Output
- 44 Oscillator Level Control
- 44 Oscillator Frequency
- 45 Oscillator Mode
- 46 SCENE MEMORY
- 46 CURRENT SCENE
- 46 DECREMENT / INCREMENT SCENE
- 47 SCENE LIST
- 47 SCENE RANGE
- 47 SELECTED SCENE
- 48 STORE SCENE
- 48 UNDO STORE
- 48 RECALL SCENE
- 49 UNDO RECALL
- 50 SETUP
- 50 Fader Delay
- 50 Cue Mode
- 50 Filled EQ Graph
- 50 Enable Inc/Dec Scene Recall
- 50 Show Send Levels in Meter Bridge
- 51 Enable Phantom Power Switching
- 51 Set EQ band to 0dB with Double-Tap
- 51 Set DCA to 0dB with Double-Tap
- 51 Channel Select – StageMix Follows Console
- 51 Channel Select – Console Follows StageMix
- 51 Input Meter Point
- 51 Output Meter Point
- 51 Display Key Input for Dynamics Meters
- 52 Troubleshooting
- 52 No Wi-Fi Available
- 52 Connection Error
- 53 Connection Lost
- 53 DHCP Server Setup on WAP/Router
- 53 Using StageMix with CL Editor
- 54 “Redirect to Internet” Problem with iOS
- 54 Graphic EQ Doesn’t Affect the Sound
- 54 Problems Moving Multiple Faders
- 54 StageMix Facebook Page