advertisement
Yamaha Professional Audio CL StageMix V4.5 User Guide
5.6.3 Dynamics On
The [DYN ON] button turns the Dynamics On/Off. This button is purple when On and grey when it is Off.
5.6.4 Dynamics Type
A button above each Dynamics curve display allows the Dynamics
Type to be selected.
Press this button then select the Processor Type from the drop-down menu.
5.6.5 Threshold
All Dynamics processors have a Threshold parameter. This parameter value is set using a vertical slider to the left of the Dynamics curve display. Next to the Threshold slider is a meter which displays the level of the Key In signal. By default, the Key In signal is the channel’s own signal (Self), post EQ. But if the Key In is changed to any other signal, this meter will display that signal’s level.
5.6.6 Range and Ratio
Depending on the Dynamics Processor type, a Range or Ratio parameter will be adjustable using a vertical slider to the right of the dynamics curve.
In and Out meters appear to the right of this vertical slider. The In meter displays the signal level going into each dynamics processor and the Out meter displays the signal level after dynamics processing.
5.6.7 Other Dynamics Parameters
All other dynamics processing parameters are adjusted using horizontal sliders below each dynamics curve.
For Compressor and Expander processors, the value for the Knee parameter is selected using a range of buttons ranging from Hard to 5.
Page 34
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 System Requirements
- 5 Wi-Fi Settings
- 6 Getting Started
- 6 CL series Network Setup
- 6 iPad Wi-Fi Settings
- 6 Using DHCP
- 7 Using a Static IP Address
- 8 StageMix Setup
- 9 OFFLINE DEMO
- 9 Configure StageMix to Work with a CL series Console
- 10 Select a Mixer and Begin Working
- 11 Edit Mixer Configurations
- 12 Mixer Window
- 12 Channel Bank Navigation
- 12 Layer Navigation
- 12 Channel Names and Colors
- 13 Faders
- 13 Long Faders
- 13 Navigation in Long Faders Mode
- 14 Channel ON
- 15 Master Bank
- 17 Digital Gain
- 17 Gain Compensation Mode
- 17 Analog Gain / Digital Gain Link
- 17 ALL GC ON
- 17 ALL GC OFF
- 17 Input Port
- 18 Phantom Power
- 18 Phase
- 19 SENDS ON FADERS
- 20 Mix Send Levels
- 20 Mix Sends ON
- 20 Mix Send PRE/POST
- 21 Global PRE/POST
- 21 Stereo Mix Pan
- 22 DCA FADERS
- 23 EQ / PAN / DYNAMICS
- 23 EQ Curve in Mixer Window
- 24 Selecting PEQ or GEQ
- 24 Accessing the EQ Editing Screens
- 25 PARAMETRIC EQ EDITING
- 27 EQ Bands
- 27 EQ ON
- 27 EQ RESET
- 28 EQ TYPE
- 28 PEQ COPY/PASTE
- 29 GRAPHIC EQ EDITING
- 29 Navigation in the GEQ Overview Section
- 29 Rack Position
- 30 GEQ Type
- 30 Insert Position
- 30 Editing GEQ Bands
- 30 Navigation in the GEQ Editing Section
- 30 GEQ ON
- 30 GEQ FLAT
- 30 GEQ Copy/Paste
- 31 PAN TO STEREO BUSSES
- 31 Balance
- 32 DYNAMICS PROCESSORS
- 33 DYNAMICS PROCESSOR EDITING
- 33 Default
- 33 Copy/Paste
- 34 Dynamics On
- 34 Dynamics Type
- 34 Threshold
- 34 Range and Ratio
- 34 Other Dynamics Parameters
- 35 Key In
- 36 OUTPORTS
- 36 Navigation
- 36 Output Port Identification
- 37 Delay On
- 37 Delay Time Display
- 37 Output Port Phase
- 37 Output Port Gain
- 37 Delay Time Editor
- 38 Delay Scale
- 38 Numeric Keypad
- 38 Nudge Delay Time Values
- 38 Copy Delay Time Value
- 39 Paste Delay Time Value
- 39 Close the Delay Time Editor
- 40 UTILITY
- 40 MUTE GROUP MASTERS
- 41 Mute Group Dim Level
- 43 TAP TEMPO
- 43 Multi-Select
- 44 OSCILLATOR
- 44 Oscillator Assign
- 44 Oscillator Output
- 44 Oscillator Level Control
- 44 Oscillator Frequency
- 45 Oscillator Mode
- 46 SCENE MEMORY
- 46 CURRENT SCENE
- 46 DECREMENT / INCREMENT SCENE
- 47 SCENE LIST
- 47 SCENE RANGE
- 47 SELECTED SCENE
- 48 STORE SCENE
- 48 UNDO STORE
- 48 RECALL SCENE
- 49 UNDO RECALL
- 50 SETUP
- 50 Fader Delay
- 50 Cue Mode
- 50 Filled EQ Graph
- 50 Enable Inc/Dec Scene Recall
- 50 Show Send Levels in Meter Bridge
- 51 Enable Phantom Power Switching
- 51 Set EQ band to 0dB with Double-Tap
- 51 Set DCA to 0dB with Double-Tap
- 51 Channel Select – StageMix Follows Console
- 51 Channel Select – Console Follows StageMix
- 51 Input Meter Point
- 51 Output Meter Point
- 51 Display Key Input for Dynamics Meters
- 52 Troubleshooting
- 52 No Wi-Fi Available
- 52 Connection Error
- 53 Connection Lost
- 53 DHCP Server Setup on WAP/Router
- 53 Using StageMix with CL Editor
- 54 “Redirect to Internet” Problem with iOS
- 54 Graphic EQ Doesn’t Affect the Sound
- 54 Problems Moving Multiple Faders
- 54 StageMix Facebook Page