- No category
advertisement
PCI-1202/1602/1800/1802 Hardware User’s Manual
2.2 Jumper Setting
2.2.1 JP1 : A/D Input Type Selection
This jumper is used to select the analog input type. For single-ended inputs, the use should connect pin1, 3 and pin2, 4. For differential inputs, pin3, 5 and pin4,
6 should be connected.
1
JP1
2
JP1
1 2
5 6
5 6
Single-Ended
Inputs (default)
Differential
Inputs
2.2.2 J1 : D/A Reference Voltage Selection
J1 is used to select the internal D/A output reference voltage. To select the
±10V voltage output, the pin 1&2 should be connected. To select the ±5V voltage output, the pin 2&3 should be connected.
J1 J1
1
± 10 Voltage output (default)
1
± 5 Voltage output
2.2.3 D/I Port Setting (PCI-1202HU/LU only)
This DI ports can be pull-high or pull-low selected by JP2. The location is given as following:
JP2
3
2
1
Pull High
JP2
Pull Low
3
2
1
Version: 3.8 (Mar.2007, PPH-014-38) ---- 19
PCI-1202/1602/1800/1802 Hardware User’s Manual
2.3 Daughter Boards
2.3.1 DB-1825
The DB-1825 is a daughter board designed for 32 channels AD cards such as ISO_AD32,
PCI-1202/1602/1802. Refer to Appendix A for “DB-1825 user manual".
37pin cable
2.3.2 DB-8225
The DB-8225 provides a on-board CJC(Cold Junction Compensation) circuit for thermocouple measurement and terminal block for easy signal connection and measurement.
The CJC is connected to A/D channel_0. The PCI-1800 can connect CON3 direct to DB-8225 through a 37-pin D-sub connector. Refer to “DB-8225 User Manual" for details.
2.3.3 DB37
The DB-37 is a general purpose daughter board for D-sub 37 pins. It is designed for easy wire connection.
2.3.4 DN37
The DN-37 is a general purpose daughter board for DIN Rail Mounting. It is designed for easy wire connection. It is Din-Rail mounting.
37pin cable
Version: 3.8 (Mar.2007, PPH-014-38) ---- 20
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION
- 8 Power Consumption
- 8 Analog Inputs
- 9 A/D Converter
- 10 A/D Trigger Methods
- 11 A/D Throughput
- 12 D/A Converter
- 13 Digital I/O
- 13 Interrupt Channel
- 13 Programmable Timer/Counter
- 15 HARDWARE CONFIGURATION
- 19 JP1 : A/D Input Type Selection
- 19 J1 : D/A Reference Voltage Selection
- 19 2.2.3 D/I Port Setting (PCI-1202HU/LU only)
- 21 DB-16P Isolated Input Board
- 22 DB-16R Relay Board
- 23 DB-24PR Power Relay Board
- 31 I/O CONTROL REGISTER
- 38 The control register
- 59 The status register
- 60 The A/D software trigger register
- 64 A/D CONVERSION OPERATION
- 71 The MagicScan Circular_Scan_Queue
- 72 The Digital Filter of MagicScan
- 72 The Different Sampling Rate of MagicScan
- 73 The High/Low Alarm of MagicScan
- 74 The MagicScan Function
- 76 The MagicScan Thread
- 79 M_FUNCTION
- 84 CONTINUOUS CAPTURE FUNCTIONS
- 90 CALIBRATION