advertisement
•
•
•
•
Delay start
You can delay the start of the program in 1-hour steps up to 24 hours.
Open the door
Press “
+
(for hidden controls only). Turn unit on using the ON/OFF button.
” button until the timer programming display jumps to 01 .
Press + or – button until the displayed time corresponds with your requirements.
Press START button. Delay start is activated.
To cancel delay start:
• Press the + or – button until “00” is indicated on the digital display.
You can change your program selection at any time until the program starts.
•
Close the door (for hidden controls only).
Cycle Completion Signal
•
•
•
•
•
•
•
The cycle completion is also indicated by a tone.This function can be changed as follows:
Open the door (for hidden controls only). Turn unit on using the ON/OFF button.
Hold down “
A
” button and press START button until the display shows H:00.
Release both buttons.
Press “
Press “ b:00
Press
A
” until the display shows “ b:02”.
C
” to increase or decrease the tone.
= Off and
b:03 = loudest
START to save the setting.
Intensive drying
The inal rinse uses a higher temperature which improves the drying result.
•
•
The running time may increase slightly. (Caution if utensils are delicate!)
•
Open the door. (for hidden controls only). Turn unit on using the ON/OFF button.
Hold down “A” button and press START the digital display shows “H:00”.
Release both buttons.
Press button “A” until the display indicates “d:00”
•
•
To change the setting,
Press button “C” (see page 4) to turn intensive drying ON = d:01 or OFF = d:00
•
Press START button. The set value is saved.
Close the door (for hidden controls only).
Operating the Unit
Switching on the appliance
•
•
•
•
•
For hidden controls, open the door.
Turn unit on by pressing the ON/OFF switch. The display of the last
selected program lashes.
The expected program duration lashes on the digital display.
Press the START button.
Close the door. The program starts running.
•
•
Interrupting the cycle
•
•
Open the door (for hidden controls only).
Press the ON/OFF button. The LEDs go out. The program is saved. If the door was opened on an appliance which has a warm water connection or is heated, irst leave the door ajar for several minutes and then close. Otherwise, expansion
(pressure) may cause the appliance door to spring open or water to run out of the appliance.
To continue the program, switch on the ON/OFF switch again.
Close the door.
15
Terminating the program
When the display indicates “0:00” it means the cycle has ended. The end of cycle is also indicated by a cycle
•
•
•
• completion signal in select models.
•
Turn unit on using the ON/OFF button.
Hold down button “
A
” button and press START until the display indicates “0:01”
Close the door. The program sequence lasts approx. 1 min.
The display will indicate 0:00
Close the door (for hidden controls only).
Child-proof lock * (select models)
The Child Safety Lock is designed to prevent children from opening the dishwasher.
•
To lock the door, push the slider below the door grip to the right.
•
To unlock the door, push the slider to the left.
Extra Tall Item Sprinkler *
If an item is too tall to be placed into the bottom rack even with the top rack in the raised position, remove the empty top rack by pulling it out of the dishwasher until it stops rolling. Pull the front of the rack upward and outward until the rollers are completely free of the roller guides.
Set the top rack aside. Push the roller guides back into the dishwasher.
16
Insert the Extra Tall Item Sprinkler into the top rack spray outlet and turn the sprinkler clockwise to lock it into position as shown above. Place your extra tall item(s) in the bottom rack as shown above.
advertisement
Related manuals
advertisement