Attaching and Removing the Adaptor. Amprobe Lamp Tester, LT-10 Lamp Tester
Add to my manuals
122 Pages
advertisement
1 Press and hold down the switch to unlock.
2 Remove the antenna from the probe.
Removing the antenna in a manner not specified in this manual may cause damages to the instrument and protection provided by the instrument may be impaired.
Attaching and Removing the Adapter Plate
Attaching adaptor plate
(clockwise)
Removing adaptor plate
(counterclockwise)
Figure 3: Attaching and removing the adapter plate
LAMP TEST
Non-contact voltage detection is always on. When the probe or the antenna is close to energized wires, LED flashes and beeps. Non-contact voltage detection will be disabled when LAMP TEST button is pressed.
W
• Verify lamp test function on a known lamp and/or on the identical lamp model both before and after use to ensure the instrument is in good working condition.
• On a very few particular linear fluorescent types, testing against the glass surface of the lamp may not respond. Testing on the lamp socket pin via the instrument’s probe (direct metal-to-metal contact) shall allow good lamp response from a working lamp.
For better results, do the following while testing:
• Press and hold down LAMP TEST button for one second and release it for one second.
7
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 10 Attaching and Removing the Antenna
- 11 Attaching and Removing the Adaptor
- 11 LAMP TEST
- 12 Testing Fluorescent Lamps
- 13 Using Sodium Lamp Antenna
- 14 VolTect™ Non-contact Voltage Detection
- 15 Voltage Detection with Antenna
- 16 Voltage Detection with Probe
- 17 Pin Test
- 30 Antenne anschließen und trennen
- 30 Adapter anbringen und trennen
- 31 Leuchtmittelprüfung
- 32 Fluoreszenzleuchten prüfen
- 33 Natriumlampen-Antenne verwenden
- 34 Berührungslose VolTect™-Spannungsprüfung
- 35 Spannungsprüfung mit der Antenne
- 36 Spannungsprüfung mit der Sonde
- 37 Kontaktprüfung
- 51 Test lampada
- 53 Utilizzo dell’antenna per lampade ai vapori di sodio
- 54 VolTect™ rilevazione della tensione senza contatto
- 55 Rilevamento della tensione con l’antenna
- 56 Rilevamento della tensione con la sonda
- 57 Test dei pin
- 71 Lamp test (medición de lámparas)
- 73 Usar una antena de lámpara de sodio
- 74 Detección de voltaje sin contacto VolTect
- 75 Detección del voltaje con la antena
- 76 Detección del voltaje con la sonda
- 77 Pin test (medición de contactos)
- 90 Montage et démontage de l'antenne
- 90 Montage et démontage de l'adaptateur
- 91 Testeur de lampes
- 93 Utilisation de l’antenne de lampe au sodium
- 94 Détection de tension sans contact VolTect
- 95 Détection de la tension avec l’antenne
- 96 Détection de tension avec la sonde
- 97 Test de broche
- 110 Sätta fast och ta bort antennen
- 110 Sätta fast och ta bort adaptern
- 111 Lamptest
- 112 Testa lysrör
- 113 Använda antenn för natriumlampa
- 114 Beröringsfri VolTect™ spänningsdetektor
- 115 Spänningsdetektion med antenn
- 116 Spänningsdetektion med sond
- 117 Stifttest