ASSEMBLY
• Assembly requires two persons.
• Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you finish all assembly steps.
• After shipping, there may be an oily substance on the exterior of the treadmill. This is normal. If there is an oily substance on the treadmill, wipe it off with a soft cloth and a mild, non-abrasive cleaner.
• Left parts are marked “L” or “Left” and right parts are marked “R” or “Right.”
• To identify small parts, see page 6.
• Assembly requires the following tools: the included hex keys one Phillips screwdriver one adjustable wrench
To avoid damaging parts, do not use power tools.
Go to www.iconsupport.eu on your computer and register your product.
• activates your warranty
• saves you time if you ever need to contact
Customer Service
• allows us to notify you of upgrades and offers
Note: If you do not have internet access, call
Customer Service (see the front cover of this manual) and register your product.
1
7
2. Make sure that the power cord is unplugged.
Remove the tie securing the Upright Wire (81) to the front of the Base (94).
Next, identify the Right Upright (90). Have a second person hold the Right Upright near the Base
(94).
See the inset drawing. Tie the wire tie (A) in the Right Upright (90) securely around the end of the Upright Wire (81). Then, insert the Upright
Wire into the lower end of the Right Upright as you pull the other end of the wire tie through the
Right Upright.
2
A
81
90
A
81
90
94
3. Lay the Right Upright (90) near the Base (94).
Press the Grommet (77) into the square hole (B) in the Right Upright. Make sure not to pinch the ground wire (C).
Next, remove and discard the indicated screw (D).
Then, attach the ground wire (C) to the Right
Upright (90) with a #8 x 1/2" Silver Screw (10).
3
94 10
77
B D
C
90
8
4. Hold the Right Upright (90) against the Base
(94). Make sure not to pinch the Upright Wire
(81).
Attach the Right Upright (90) with two 3/8" x
2 3/8" Screws (7), a 3/8" x 1 1/4" Screw (63), a 3/8" x 1 3/4" Screw (62), and four 3/8" Star
Washers (13) as shown; do not fully tighten the Screws yet.
Attach the Left Upright (not shown) in the
same way. Note: There are no wires on the left side.
4
5. Identify the Left and Right Base Covers (82, 83).
Slide the Left and Right Base Covers onto the
Left and Right Uprights (89, 90) as shown.
5
94
63
13
90
89
82
7
13
81
13
62
90
83
9
6. Attach a Handrail (84) to the Right Upright (90) with a 5/16" x 2 1/2" Screw (28) and a 5/16" Star
Washer (11) in the location shown. Make sure not to pinch the Upright Wire (81). Do not fully tighten the Screw yet.
Then, remove and discard the two indicated screws (E).
Attach the other Handrail (not shown) to the
Left Upright (89) in the same way. Note: There are no wires on the left side.
6
89
84
28
E
11
81
90
7. IMPORTANT: To avoid damaging the Pulse
Crossbar (93), do not use power tools and do not overtighten the #10 x 3/4" Screws (9).
Orient the Pulse Crossbar (93) as shown. Attach the Pulse Crossbar to the Handrails (84) with four #10 x 3/4" Screws (9) and four #10 Star
Washers (5); start all four Screws, and then tighten them. Make sure not to pinch the
Upright Wire (81).
Next, tighten two 5/16" x 2 1/2" Screws (28) with two 5/16" Star Washers (11) into the Pulse
Crossbar (93) as shown.
Firmly tighten the four 5/16" x 2 1/2" Screws
(28).
Then, remove the wire tie (A) from the Upright
Wire (81).
7
84
28
11
9
5
28
93
84
81
A
28
28
5
11
9
10
8. Set the Console Base (64) face down on a soft surface to avoid scratching the Console Base.
Identify the Left Tray (36). Attach the Left Tray with four #8 x 3/8" Screws (105).
Next, attach the Right Tray (27) with four #8 x
3/8" Screws (105).
Then, remove and save the four 1/4" x 1/2"
Screws (2).
8
2
27
105
64
36
105
9. With the help of a second person, hold the console assembly (F) near the right Handrail (84) and the left Handrail (not shown).
See the inset drawing. Connect the Upright
Wire (81) to the console wire (G). The connec- tors should slide together easily and snap
into place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE
CONNECTORS PROPERLY, THE CONSOLE
MAY BECOME DAMAGED WHEN YOU TURN
ON THE POWER.
9
F
84
G
81
A
G
81
2
11
10. Set the console assembly (F) on the Handrails
(84). Make sure that no wires are pinched.
Insert the excess Upright Wire (81) into the Right
Upright (90).
Attach the console assembly (F) to the brackets on the Handrails (84) with the four 1/4" x
1/2" Screws (2) that you removed in step 8 and four 1/4" Star Washers (26); firmly tighten the
Screws.
10
84
2
26
81
90
F
26
2
11. Identify the Right Handrail Cover (31). Set the
Right Handrail Cover on the right Handrail (84).
Tighten three #8 x 1/2" Screws (1) into the bottom of the Right Handrail Cover; do not fully tighten the Screws.
Next, slide the Right Handrail Cover (31) forward until it slides under the console assembly (F).
Then, tighten the three #8 x 1/2" Screws (1); do not overtighten the Screws.
Attach the Left Handrail Cover (87) in the
same way.
11
87
1
84
84
31
F
1
84
12
12. Slide the Right and Left Handrail Grips (74, 79) over the Right and Left Handrail Covers (not shown) and against the console assembly (F).
Attach the Handrail Grips (74, 79) with two
#8 x 1/2" Screws (1); do not overtighten the
Screws.
12
79
F
1
1
74
13. Hold the Pulse Bar (85) near the console assembly (F). Connect the two pulse wires (H), and connect the Console Ground Wire (58) to the ground wire (I) from the console assembly (F).
Attach the Pulse Bar (85) to the Pulse Crossbar
(93) with eleven #8 x 1/2" Screws (1); start all eleven Screws, and then tighten them. Make sure that no wires are pinched.
13
85
1
93
1 58
1
H
I
F
13
14. Raise the Frame (56) to the upright position.
IMPORTANT: Do not raise the Frame past the vertical position. Have a second person hold the Frame until step 16 is completed.
Remove the two 5/16" x 3/4" Screws (6) from the
Latch Crossbar (114).
Orient the Latch Crossbar (114) as shown. Make sure that the “This side toward belt” sticker
(J) is facing the treadmill. Attach the Latch
Crossbar to the brackets (K) on the Frame (56) with two 5/16" x 3/4" Screws (6) that you just removed and two 5/16" Star Washers (11).
14
11
6
56
K
114
J
K
11
6
15. Remove the 5/16" Nut (34) and the 5/16" x 1 3/4"
Bolt (41) from the bracket on the Base (94).
Next, orient the Storage Latch (52) as shown.
Attach the lower end of the Storage Latch (52) to the bracket on the Base (94) with the 5/16" x
1 3/4" Bolt (41) and the 5/16" Nut (34).
Then, raise the Storage Latch (52) to a vertical position, and remove the tie (L).
15
L
52
34
94
41
14
16. Remove the 5/16" Nut (34) and the 5/16" x 2 1/4"
Bolt (106) from the bracket on the Latch Crossbar
(114).
Align the upper end of the Storage Latch (52) with the bracket on the Latch Crossbar (114), and insert the 5/16" x 2 1/4" Bolt (106) through the bracket and the Storage Latch. This will push a spacer (M) out of the Storage Latch; discard the spacer.
Next, tighten the 5/16" Nut (34) onto the 5/16" x
2 1/4" Bolt (106). Do not overtighten the Nut; the Storage Latch (52) must be able to pivot.
Then, lower the Frame (56) (see HOW TO
LOWER THE TREADMILL FOR USE on page
25).
16
56
34 M 114
106
52
17. Firmly tighten the four 3/8" x 2 3/8" Screws
(7), the two 3/8" x 1 3/4" Screws (62), and the two 3/8" x 1 1/4" Screws (63).
Next, set the Left Inner Base Cover (100) onto the lower end of the Left Upright (89). Then, slide the Left Base Cover (82) downward and press it onto the Left Inner Base Cover.
Next, set the Right Inner Base Cover (101) onto the lower end of the Right Upright (90). Then, slide the Right Base Cover (83) downward and press it onto the Right Inner Base Cover.
17
83
63
90 7
62
63
89
82
100
101
7
62
15
18. Attach the Tablet Holder (25) to the console assembly (F) with four #8 x 5/8" Machine Screws
(8); start all four Screws, and then tighten them. Do not overtighten the Screws.
18
25
8 8
F
19. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. To avoid damage to the console, keep the treadmill out of direct sunlight. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see pages 27 and 28). Note: Extra hardware may be included.
16
