- Home
- Do-It-Yourself tools
- Garden tools
- Lawnmowers
- Toro
- Mid-Size ProLine Pistol Grip Hydro, 15 HP
- User manual
Adjusting the Handle Height. Toro Mid-Size ProLine Pistol Grip Hydro, 15 HP
Add to my manuals
64 Pages
advertisement
Figure 25
1. Center Gage Wheels and
Spacer
2. Nut
3. Bolt
4. Washer
5. Spacer
Adjusting the Handle Height
The handle position can be adjusted to match the operator’s height preference.
1. Remove the hairpin cotter pins and clevis pins from the drive levers and neutral locks
(Figure 26).
1. Speed control rod
2. Swivel
Figure 27
3. Nut
3. Loosen the upper flange bolts (3/8 x 1-1/4 inches) and flange nut securing handle to rear frame (Figure 28).
4. Remove the lower flange bolts (3/8 x 1 inch) and flange nuts securing handle to rear frame
(Figure 28).
5. Pivot handle to desired operating position and install lower flange bolts (3/8 x 1 inch)and flange nuts into mounting holes. Tighten all flange bolts.
Figure 26
1. Control rod
2. Clevis pin
3. Drive lever
4. Operator Presence Control lever (OPC)
5. Left handle shown
6. Neutral lock
7. Hairpin cotter pin
2. Loosen the nuts holding the swivel connected to the speed control crank (Figure 27).
28
Figure 28
1. Control rod tting
2. Lower mounting holes
3. Rear frame
4. Lower ange bolt (3/8 x 1 inch)
5. Upper ange bolt (3/8 x
1-1/4 inches)
6. High position
7. Lower position
8. Upper mounting hole
9. Handle
10. Flange nut (3/8 inch)
11.
6. Adjust the swivel on the speed control rod and tighten the nuts against the swivel (Figure 27).
7. Adjust the control rod length by rotating the control rod in the rod fitting (Figure 27).
8. Install hairpin cotter between drive levers and neutral locks and into clevis pins (Figure 26).
Note:
Make sure the clevis pins are inserted into the neutral locks.
9. Perform the hydraulic linkage adjustments when the handle height is changed; refer
Hydraulic Linkage Adjustments.
29
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Introduction
- 4 Safety
- 4 Safe Operating Practices
- 5 Toro Mower Safety
- 7 Slope Chart
- 8 Safety and Instructional Decals
- 11 Setup
- 12 Washers
- 12 Assembly
- 13 3 Installing the Fuel Tank
- 14 4 Installing the Control Rods
- 15 and Spacers
- 16 Engine Oil Level
- 16 Linkage
- 17 the Safety Video
- 18 Product Overview
- 18 Controls
- 20 Operation
- 20 Adding Fuel
- 21 Checking the Engine Oil Level
- 21 Think Safety First
- 21 Operating the Parking Brake
- 22 Engine
- 23 Operating the Neutral Locks
- 23 Control (PTO)
- 24 The Safety Interlock System
- 25 Backward
- 25 Position
- 25 Stopping the Machine
- 26 Pushing the Machine by Hand
- 26 Transporting Machines
- 26 Using the Side Discharge
- 27 Adjusting the Height-of-Cut
- 27 Wheels
- 28 Adjusting the Handle Height
- 30 Maintenance
- 30 Schedule(s)
- 30 Lubrication
- 30 How to Grease
- 31 Where to Add Grease
- 31 Lubricating the Bearings
- 31 Idler
- 32 Engine Maintenance
- 32 Servicing the Air Cleaner
- 33 Servicing the Engine Oil
- 34 Servicing the Spark Plug
- 35 Fuel System Maintenance
- 35 Servicing the Fuel Tank
- 36 Servicing the Fuel Filter
- 36 Electrical System Maintenance
- 36 Servicing the Fuses
- 37 Drive System Maintenance
- 37 Linkage
- 38 Adjustment
- 38 Linkages
- 40 Adjusting the Neutral Stud
- 41 Adjusting the Control Rod
- 42 Adjusting the Tracking
- 42 Checking the Tire Pressure
- 43 Bushings
- 44 Bearings
- 44 Adjusting the Electric Clutch
- 45 Cooling System Maintenance
- 45 Cleaning the Air Intake Screen
- 45 Brake Maintenance
- 45 Servicing the Brake
- 46 Belt Maintenance
- 46 Replacing the Mower Belt
- 46 Replacing the PTO Drive Belt
- 47 Hydraulic System Maintenance
- 47 System
- 50 Mower Deck Maintenance
- 50 Servicing the Cutting Blades
- 52 Frame Set Up
- 54 Front-to-Rear Pitch
- 54 Pitch
- 54 Measurements
- 55 Matching the Height of Cut
- 55 Replacing the Grass Deflector
- 57 Storage
- 57 Cleaning and Storage
- 58 Troubleshooting
- 61 Schematics