- Home
- Do-It-Yourself tools
- Garden tools
- Lawnmowers
- Toro
- Mid-Size ProLine Pistol Grip Hydro, 15 HP
- User manual
advertisement
1. Yoke
2. Parking brake lever
(released position)
3. Clevis pin
4. Haripin cotter
Figure 62
5. Jam Nut
6. Brake rod
7. Lower brake lever
8. 1 o’clock position
1. Mower belt
2. Idler arm spring
3. Outward pulley
Figure 63
4. PTO Drive Belt
5. Double Spindle Pulley
Belt Maintenance
Replacing the Mower Belt
Check the belts every 50 hours.
Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks and cracks are signs of a worn deck belt. Replace the deck belt if any of these conditions are evident.
1. Disengage the PTO and set the parking brake.
2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
3. Remove the knobs/rubber washers holding the carrier frame cover and remove the carrier frame cover.
4. Remove the knobs/rubber washers holding the belt cover to the cutting unit and remove the belt cover.
5. Remove the PTO drive belt. Refer to Replacing the PTO Drive Belt in Belt Maintenance,
6. Disconnect the idler arm spring to relieve tension on the idler arm and idler pulley, then remove the worn mower belt (Figure 63).
7. Install the new mower belt around the outward spindle pulley, the idler pulley, and in the lower groove of the double spindle pulley (Figure 63).
8. Reconnect the idler arm spring (Figure 63).
9. Install the PTO drive belt. Refer to Replacing the PTO Drive Belt in theBelt Maintenance,
10. Reinstall the belt cover onto the cutting unit, then reinstall and tighten the knobs/rubber washers.
11. Install the carrier frame cover onto the cutting unit, then install and tighten the knobs/rubber washers.
Replacing the PTO Drive Belt
Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks and cracks are signs of a worn drive belt. Replace the drive belt if any of these conditions are evident.
1. Disengage the PTO and set the parking brake.
2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
3. Remove the knobs/rubber washers holding the carrier frame cover and remove the carrier frame cover.
46
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Introduction
- 4 Safety
- 4 Safe Operating Practices
- 5 Toro Mower Safety
- 7 Slope Chart
- 8 Safety and Instructional Decals
- 11 Setup
- 12 Washers
- 12 Assembly
- 13 3 Installing the Fuel Tank
- 14 4 Installing the Control Rods
- 15 and Spacers
- 16 Engine Oil Level
- 16 Linkage
- 17 the Safety Video
- 18 Product Overview
- 18 Controls
- 20 Operation
- 20 Adding Fuel
- 21 Checking the Engine Oil Level
- 21 Think Safety First
- 21 Operating the Parking Brake
- 22 Engine
- 23 Operating the Neutral Locks
- 23 Control (PTO)
- 24 The Safety Interlock System
- 25 Backward
- 25 Position
- 25 Stopping the Machine
- 26 Pushing the Machine by Hand
- 26 Transporting Machines
- 26 Using the Side Discharge
- 27 Adjusting the Height-of-Cut
- 27 Wheels
- 28 Adjusting the Handle Height
- 30 Maintenance
- 30 Schedule(s)
- 30 Lubrication
- 30 How to Grease
- 31 Where to Add Grease
- 31 Lubricating the Bearings
- 31 Idler
- 32 Engine Maintenance
- 32 Servicing the Air Cleaner
- 33 Servicing the Engine Oil
- 34 Servicing the Spark Plug
- 35 Fuel System Maintenance
- 35 Servicing the Fuel Tank
- 36 Servicing the Fuel Filter
- 36 Electrical System Maintenance
- 36 Servicing the Fuses
- 37 Drive System Maintenance
- 37 Linkage
- 38 Adjustment
- 38 Linkages
- 40 Adjusting the Neutral Stud
- 41 Adjusting the Control Rod
- 42 Adjusting the Tracking
- 42 Checking the Tire Pressure
- 43 Bushings
- 44 Bearings
- 44 Adjusting the Electric Clutch
- 45 Cooling System Maintenance
- 45 Cleaning the Air Intake Screen
- 45 Brake Maintenance
- 45 Servicing the Brake
- 46 Belt Maintenance
- 46 Replacing the Mower Belt
- 46 Replacing the PTO Drive Belt
- 47 Hydraulic System Maintenance
- 47 System
- 50 Mower Deck Maintenance
- 50 Servicing the Cutting Blades
- 52 Frame Set Up
- 54 Front-to-Rear Pitch
- 54 Pitch
- 54 Measurements
- 55 Matching the Height of Cut
- 55 Replacing the Grass Deflector
- 57 Storage
- 57 Cleaning and Storage
- 58 Troubleshooting
- 61 Schematics