13. EXIT AND ENTRY DELAY. Eldes ESIM384

13. EXIT AND ENTRY DELAY

When arming, the system initiates the exit delay countdown (by default – 15 seconds) intended for the user to leave the secured area. The exit delay is indicated by short beeps emitted by EKB2/EKB3/EKB3W/EWKB4 keypad buzzer and buzzer, connected to the alarm system.

When arming:

• a non-partitioned system, a countdown timer will be displayed in the home screen view of EKB2 during exit delay.

• a partitioned system, EKB2 keypad will display ARMING part-name message on the screen for 2 seconds and switch to partition selection menu during exit delay.

Exit delay is provided when arming the system by the following methods:

• EKB2/EKB3/EKB3W/EWKB4 keypad and user/master code.

• iButton key.

• Arm/Disarm by Zone.

To arm the system without exit delay, use one of the following system arming methods:

• Free of charge phone call.

• SMS text message.

• EWK2/EWK2A wireless keyfob

• EGR100 middle-ware.

Set exit delay

SMS

EKB2

SMS text message content: ssss EXITDELAY:p,ext or ssss EXITDELAY:p,ext;p,ext;p,ext;p,ext

Value: ssss – 4-digit SMS password; p – partition number, range – [1... 4], ext – exit delay duration, range – [0... 600] seconds.

Example: 1111 EXITDELAY:1,20;3,43

Menu path:

OK → iiii → OK → PRIMARY SETTINGS → OK → EXIT DELAY → OK → PARTITION 1... 4 → OK → ext → OK

Value: iiii – 4-digit installer code;, ext – exit delay duration, range – [0... 600] seconds.

EKB3/

EKB3W/

EWKB4

Enter parameter 72, partition number and exit delay duration:

72 pp ext #

Value: pp – partition number, range – [01... 04], ext – exit delay duration, range – [0... 600] seconds.

Example: 7203259#

Eldes

Utility

This operation may be carried out from the PC using the Eldes Utility .

NOTE: Alternatively, you can set exit delay value to “0” in order to arm the system without exit delay by any available method.

NOTE: EKB3/EKB3W/EWKB4 keypad buzzer will only beep if the keypad is operating in the partition where exit delay countdown is in progress.

ESIM384 Installation and Configuration Manual v1.5

EN

Once the exit delay has expired, the system is armed. Upon return and violation of delay zone, the system will initiate the entry delay countdown (by default – 15 seconds) after the user has entered the secured area. The countdown is indicated by short beeps provided emitted by keypad internal buzzer. Once the user presses/touches any key on the keypad during this delay, the buzzer of the keypad will be silenced.

Entry delay countdown is intended for user to enter a valid user code and disarm the system before the alarm is caused.

Set entry delay for

Delay zone

SMS

SMS text message content: ssss ENTRYDELAY:nn,eeeee or ssss ENTRYDELAY:nn,eeeee;nn,eeeee;nn,eeeee;nn,eeeee

Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 144], eeeee – entry delay duration, range – [0... 9999] seconds.

Example: 1111 ENTRYDELAY:1,25;54,14;12,20

EKB2

Menu path:

On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 16 → OK

→ ENTRY DELAY → OK → eeeee → OK

Wireless zone: OK → iiii → OK → WIRELESS ZONES → OK → WIRELESS ZONES 1... 4 → OK →

WIRELESS ZONE 17... 144 → OK → ENTRY DELAY → OK → eeeee → OK

Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD

ZONE → OK → ENTRY DELAY → OK → eeeee → OK

EPGM1 zone: ... → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 → OK → EPGM1 ZONE 1... 32 →

OK → ENTRY DELAY → OK → eeeee → OK

Value: iiii – 4-digit installer code; eeeee – entry delay duration, range – [0... 9999] seconds.

EKB3/

EKB3W/

EWKB4

Enter parameter 54, partition number and entry delay duration:

54 nn eeeee #

Value: nn – zone number, range – [01... 144] , eeeee – entry delay duration, range – [0... 9999] seconds

Example: 5403259#

Eldes

Utility

This operation may be carried out from the PC using the Eldes Utility .

NOTE: Due to battery power saving reasons, EKB3W/EWKB4 keypad buzzer will not sound during entry delay if the violated Delay type zone is not of the associated EKB3W/EWKB4 keypad.

For more details on zone types, please refer to 14.5. Zone Type Definitions.

56 EN ESIM384 Installation and Configuration Manual v1.5