Problem
There are residues of food or liquids within the mincer coupling of the mixing arm.
Reason
The processed food has been too runny and/or too juicy.
Easy solution
Only process types of food via the mincer, which do not give off much juices when being pressed. The mincer is
NOT suited for juicing fruit and vegetables. Additionally, it is not suited for processing any type of runny food. Do not pour any liquids into the feed chute, while the mincer is assembled to the mixing arm of the machine.
The screw ring got loose. When assembling the mincer, turn the screw ring somewhat tighter. However, do not turn it with violence. Ensure that the mincer is assembled completely and correctly
(see: ‘Using the Mincer’).
The mincer is not assembled correctly.
Ensure to assemble the mincer completely and correctly according to the instructions, before starting operation (see: ‘Using the Mincer’).
CARE AND CLEANING
WARNING – Always ensure that the machine is out of reach of young children!
Do not hold your hands or any foreign objects (e.g. cooking utensils, brushes, clothes) onto the moving parts (mixing drive, mixing tools, worm shaft and cross blade of the mincer), while the machine is connected to the power supply.
Always switch off the motor (press the control dial) and unplug from the mains power supply, before moving or cleaning the machine. Do not touch the machine with wet hands or when the machine is wet (e.g. by condensate), while the machine is connected to the power supply. Do not place the machine on a power cord or on wet surfaces. Do not immerse the machine or power cord into water or any other liquid. Do not spill any liquids onto the machine.
CAUTION – Do not use any hard or sharp-edged objects, corrosive chemicals, disinfectants, abrasive cleaners, or metal scouring pads for cleaning the machine or any part of it. Do not poke with any foreign objects in the mincer coupling, mixing drive, or in the joint of the mixing arm. Do not use violence. Do not place the machine or the power cord in an automatic dishwasher. Additionally, some accessories and tools are NOT suited for cleaning via hot water and/or in an automatic dishwasher (see below: ‘Cleaning in an Automatic Dishwasher’).
EN 122
PREPARATION FOR CLEANING
1. Press the control dial until only dashes are shown on the display areas (see:
‘After Usage’). Unplug the machine.
2. Remove the removable parts (see: ‘After Usage’).
CLEANING THE HOUSING
IMPORTANT - For getting a stable stand on the work surface, the suction cups at the feet of the machine must be clean. Usually, you do not need to clean the suction cups. However, when flour or sticky liquids have been on the work surface, the suction cups may get polluted, causing the machine to excessively move around during operation. In this case, you should remove any pollution from the suction cups. For this, always use only soft clothes. Do not scratch or scrape on the suction cups.
3. Hold the unlock button at the joint of the mixing arm pressed, while moving the mixing arm to the upper position. Ensure that the mixing arm engaged securely in this position.
4. If required, remove any residues and splashes from the drive shafts of the mixing drive and from the bottom of the mixing arm with a soft, slightly damp cloth. Then press the unlock button and slowly lower the mixing arm to the operating position.
5. Wipe the housing of the mixer. Avoid dripping any liquids into the joint of the mixing arm. Wipe any food particles from the power cord.
6. Carefully wipe dry the housing after cleaning. If required , carefully clean the suction cups at the feet of the base plate: For this, the mixing arm must be engaged in the lower operating position. Lay the machine (without mixing tools and mixing bowl) carefully onto its left side . Use a SOFT, damp cloth for cleaning.
After removing any residues, wipe with clear water and thoroughly dry the suction cups via a soft cloth.
CLEANING THE TOOLS AND ACCESSORIES
IMPORTANT - Do not clean the mincing discs in the automatic dishwasher.
We recommend to clean the steel mincing discs regularly, even when they have not been used. This will avoid a rancid or resinous taste and smell. Always rub the mincing discs with some cooking oil after cleaning. If you wish to use an automatic dishwasher for cleaning, carefully observe the instructions given in the following section (‘Cleaning in the Automatic Dishwasher’).
123 EN