advertisement
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Refer to the drawings below to identify the small parts used in assembly. Assembly requires the included allen wrench as well as a phillips screw- driver , two adjustable wrenches , and scissors .
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
3/4” Screw (55)–4
Handrail Bolt (15)–2
Handrail Washer (16)–2
5/16" Washer (32)–2
Handrail Nut (82)–2
Latch Screw (74)–2 Extension Leg Screw (34)–2
3 1/2" Handrail Bolt (59)–2
1. With the help of a second person, carefully raise the
Uprights (14), the Right Handrail (57), and the Console
Base (6) to the position shown. Be careful not to pull on
the Wire Harness (26). Set the Right Handrail on the right
Upright until step 3 is completed.
Refer to the inset drawing. Insert one of the Extension
Legs (41) into the treadmill as shown. (Note: It may be helpful to tip the Uprights [14] in the direction shown by the arrow as you insert the Extension Leg.) Make sure that the Base Pad (36) is on the bottom of the Extension
Leg. Attach the Extension Leg with an Extension Leg
Screw (34). Be sure to push on the head of the
Extension Leg Screw while tightening it.
Attach the other Extension Leg (41) in the same way.
1
6
57
14
26
14
36
41
34
2. Attach the Storage Latch (12) to the left Upright (14) with two Latch Screws (74). Tighten the Screws until they are snug; do not overtighten the Screws.
2
14
74
12
5
3. Cut the plastic tie holding the cage nut in the upper end of
Left Handrail (2).
Position the Left Handrail (2) on the left Upright (14). The lower end of the Left Handrail should be on the outside of the Extension Leg (41) as shown. Thread a Handrail Bolt
(15) with a Handrail Washer (16) into the left Upright and the Left Handrail. Do not tighten the Handrail Bolt yet.
Attach the lower end of the Left Handrail (2) to the
Extension Leg (41) with a 3 1/2” Handrail Bolt (59), a
5/16” Washer (32), and a Handrail Nut (82). Do not tighten the Handrail Nut yet.
3
15
16
14
2
41
82
59
32
4. Have a second person hold the Console Base (6) and the
Right Handrail (57) near the right Upright (14) as shown.
Pull any slack wire from the Console Base through the
Bracket. Fold the Wire Harness (26) as shown and insert the folded Wire Harness into the Right Upright.
Cut the indicated plastic tie off the Handrail (57).
Make sure that the Wire Harness (26) is inside of the bracket on the Right Handrail (57) and insert the bracket into the right Upright (14). Make sure that the Wire
Harness is not pinched.
5. Set the Console Base (6) on the Left and Right Handrails
(2, 32). Thread a Handrail Bolt (15) with a Handrail Washer
(16) into the right Upright (14) and the Right Handrail (32).
Do not tighten the Handrail Bolt yet.
Attach the lower end of the Right Handrail (32) to the
Extension Leg (41) with a 3 1/2” Handrail Bolt (59), a 5/16”
Washer (32), and a Handrail Nut (82).
Tighten all parts used in this step and in step 3.
4
5
Bracket
57
2
6
6
32
26
Plastic Tie
14
16
14
15
82
41
32
59
6. Attach the Console Base (6) to the Handrails (2, 57) by threading four 3/4” Screws (55) into the Console Base. After all four Screws have been started, tighten the Screws until they are snug; do not overtighten the Screws.
6
57
7. Make sure that all parts are properly tightened before
you use the treadmill. Keep the included allen wrench in a safe place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet, place a mat under the treadmill.
6
55
6
2
55
advertisement