Instructions. Whirlpool CGT8000XQ

ELECTRONIC CONTROL SETUP INSTRUCTIONS

Washer control

NOTE: After the washer/dryer has been installed and plugged in, the display will show “0 MINUTES” on the washer and dryer portions of the display. After the washer and dryer doors have been opened and closed, the display will show the price for each machine. On washer/dryers set for free cycles, the display sections will flash “SELECT CYCLE.”

1.

With a coin drop attached: Insert coins until “SELECT

CYCLE” flashes on the display portion of the washer or dryer that is to be run.

Alternately, Generation 1 or 2 debit card systems may be used; but when the Generation 2 debit system is used, the controls will automatically be set to Enhanced Debit mode

(J. Ed). In Enhanced Debit mode, the card balance will also display when a debit card is inserted into the reader.

2.

Door must be closed on the desired washer/dryer before cycle selection is made.

3.

Press the fabric setting button for the washer/dryer cycle desired. For washer cycles, also select the desired wash temperature. After the cycle is started, the time will display and count down.

4.

If a cycle is interrupted by opening the door or power loss,

“RESELECT CYCLE” will flash in the display. To restart the washer/dryer, close door and reselect desired cycle.

NOTE: When set for free vend operation an ongoing dryer cycle will cancel if the door is opened.

Dryer control

General Washer/Dryer User Information

SCROLLING “OUT OF ORDER” FOLLOWED BY

DIAGNOSTIC CODE SHOWING IN DISPLAY – This condition indicates the washer or dryer is inoperative. Diagnostic codes being displayed on the upper portion of the display pertain to the dryer section, and diagnostic codes displayed on the lower portion of the display apply to the washer section. Diagnostic codes displayed on both the upper and lower portions of the display pertain to the control system of both the washer and dryer.

“0 MINUTES” SHOWING IN DISPLAY – This indicates the cycle is complete and the washer/dryer cannot be operated.

Coins dropped or debit inputs during this condition will be stored in escrow but cannot be used until normal operation is restored by opening and closing the door. If a door switch has failed, causing “0 MINUTES” to remain in the display after the door is opened and closed, it must be replaced before normal operation can be restored.

COLD START (Initial first use) – Washer/dryer is programmed at the factory as follows:

Washer

Dryer

11-minute wash period

$1.75 wash price

3 rinses (extra rinse not enabled)

5 minutes per quarter

$1.50 dry price (fixed cycle with top off)

33


WARM START (after power failure) – A few seconds after power is restored, if a cycle was in progress at the time of the power failure, “RESELECT CYCLE” will flash in the display, indicating the need for a key press to restart washer or dryer.

DEBIT CARD READY – This washer/dryer is debit card ready.

It will accept a variety of debit card systems, but does NOT come with a debit card reader. Refer to the debit card reader manufacturer for proper washer/dryer set-up. In models converted to a Generation 1 debit card system, debit pulses represent the equivalent of one coin (coin 1).

WASHER DOOR LOCK – Prior to beginning a cycle, there is a door lock routine of lock/unlock/relock, then cycle begins. The door will remain locked until the end of a cycle or approximately

2 minutes after a power interruption.

Control Set-up Procedures

IMPORTANT: Read all instructions before operating.

PRICING – After the door is opened and then closed following the completion of a cycle, the display indicates the cycle price (unless set for free operation, where the display will flash

“SELECT CYCLE”). As coins are dropped or debit inputs arrive, the display will change to lead the user through the initiation of a cycle.

There are four (4) types of dryer pricing:

Insert service switch key and turn counterclockwise.

Once a Generation 2 debit card reader is installed (according to the reader manufacturer’s instructions), the set-up modes can be changed only by inserting a set-up card (supplied by the reader manufacturer) into the card slot. Inserting the service switch key and turning will only access the service mode.

Fixed “Vend” Pricing

A dryer set up for “Fixed Cycle” operation can only accept additional time accumulated by increments equal to the length of a complete dry cycle. A maximum of 99 minutes may be purchased; no additional credit is given for coins dropped with 99 minutes in the display.

The washer/dryer is now in set-up mode. The lower temperature setting buttons and the lower portion of the display are used to set up the digital control for the washer. The upper three fabric setting buttons and the upper portion of the display are used to set up the controls for the dryer.

Accumulator Pricing

The display can contain 4 numbers and/or letters and a decimal point on both the top and bottom display portions. These are used to indicate the set-up codes and related code values available for use in programming the washer/dryer.

If the price is set to one coin 1, then accumulator pricing is in effect. Cycle time can be purchased one coin at a time up to the maximum time of 99 minutes.

Fixed Cycle With Top Off Pricing

A dryer set to offer “Top Off” capability will allow time to be added to an existing dry cycle in increments equal to the number of minutes of dry time per quarter (coin 1), up to 99 minutes, regardless of the cost required to start the dryer. No credit is given for coins or debit inputs entered when the control is displaying 99 minutes.

In Enhanced Debit Mode, the top off price can be set independently (see VALUE OF COIN 2), and the top off time is calculated according to the following equation: top off time =

top off price

x full cycle length

full cycle price

Penny increment offset is not applied to top off purchases.

How to Use the Buttons to Program the Controls

1. The lower-left (HOT) button is used to adjust the values associated with washer set-up codes and the upperleft (COTTON/WHITES) button is for the dryer. Pressing the button will change the value by increments. Rapid adjustment is possible by holding the button down.

2.

The lower-middle (WARM) button will advance through the set-up codes. Pressing the button will advance both the washer and dryer to the next available set-up code. Some set-up codes are washer- or dryer-specific and will not be displayed on both the washer and dryer portions of the display. Holding down the lower-middle (WARM) button will automatically advance through the set-up codes at a rate faster than 1 per second.

3.

The lower-right (COLD) button is used to select or deselect washer options; upper-right (COLORS/DELICATES) is used for dryer option selection or deselection.

FREE CYCLES – This is established by setting the cycle price to zero. When this happens, “SELECT CYCLE” will appear rather than a cycle price. Any cycle started as a free cycle will automatically terminate when the door is opened.

34


Start Operating Set-up

Washer/dryers are preset at the factory and do not require any programming. However, if you want to change the settings, follow the “Set-Up Codes” guide.

The first code shown in each segment is the factory default setting.

The set-up code is indicated by the one or two left-hand characters. The set-up code value is indicated by the two or three right-hand characters.

Set-Up Codes

Code Explanation

6 07 REGULAR CYCLE PRICE (WASHER)

6 07 Represents the number of quarters (coin 1) needed to start the washer; may adjust from 0–39. (See

VALUE OF COIN 1.) Advance from 0–39 by pressing the lower-left (HOT) button. Factory default of 7 quarters = $1.75.

• Press the lower-middle (WARM) button once to advance to next code.

REGULAR CYCLE PRICE (DRYER) 606

606 Represents the number of quarters (coin 1) needed to start the dryer; may adjust from 0–39

(See VALUE OF COIN 1). Advance from 0–39 by pressing the upper-left (COTTON/WHITES) button.

Factory default of 6 quarters = $1.50.


REGULAR DRY TIME (DRYER) 705

705 Represents the number of minutes per quarter

(coin 1). Factory default of 5 minutes per coin.

Example: 6 quarters x 5 minutes = 30 minutes.

By pressing the upper-left (COTTON/WHITES) button, value adjusts from 1–99 minutes.


8 00 ADDITIONAL RINSE OPTION (WASHER)

This option is either NOT SELECTED “00” or SELECTED “Ar.”

8 00

8 Ar

Not Selected “00.”

Selected “Ar.” Cannot be combined with the Super

Cycle rinse option.

• Press the lower-right (COLD) button once to change this selection.


TYPE OF DRYER PRICING (DRYER) 800

800 Fixed Cycle with Top Off. For detailed description, see “General Washer/Dryer User Information.”

8FC Fixed Cycle. For detailed description, see “General Washer/Dryer

User Information.” Use the upper-right (COLORS/

DELICATES) button to change this selection.



9 00

9 00

9 0C

CYCLE COUNTER OPTION

This option is either NOT SELECTED “00” or SELECTED “0C.”


Selected “0C” and not able to be deselected.

• Press the lower-right (COLD) button

3 consecutive times to select “0C.” Once

selected “0C” it cannot be deselected.


If cycle counter (9 0C) is selected, the following is true:

1 00

2 00

Cycles in HUNDREDS

Cycles in ONES

1 02 = 200

2 25 = 25

TOTAL CYCLES = 225

This is “VIEW ONLY” and cannot be cleared.



1. 00 MONEY COUNTER OPTION

This option is either NOT SELECTED “00” or SELECTED “0C.”

1. 00

1. 0C

1. C0

2. 00


Selected “0C.”


3 consecutive times to select “0C” and 3 consecutive times to deselect (Not Selected

“00”). Counter resets by going from “OFF” to “ON.”

Selected “0C” and not able to be deselected.

• To select “C0” and not able to be deselected, first select “0C,” then within 2 seconds, press the lower-middle (WARM) button twice, the lower-left

(HOT) button once, and exit set-up mode.


SPECIAL PRICING OPTIONS

This option is either NOT SELECTED “00” or SELECTED “SP.”

2. 00

2. SP

Not Selected “00,” and next available code will be A.00

Selected “SP.”


If SPECIAL PRICING OPTION is selected, there is access to codes “3.XX” through “9.XX.”


If money counter (1.0C or 1.C0) is selected, the following is true:

3 00

4 00

5 00

Dollars in HUNDREDS

Dollars in ONES

Number of CENTS

3 01 = $100.00

4 68 = $ 68.00

5 75 = $ 00.75

TOTAL = $168.75

35


OPTIONS 3.XX – 9.XX TO USE IF SPECIAL PRICING

IS SELECTED


3. 07

3. 07

3.06

3.06

4.05

4.05

5. 00

5. 00

6. 00

6. 00

7. 00

7. 00

8. 00

8. 00

SPECIAL CYCLE PRICE (WASHER)

Represents the number of quarters (coin 1) to start the washer; may adjust from 0–39. (See VALUE OF

COIN 1.)

• Advance from 0–39 by pressing the lower-left

(HOT) button. Factory default of 7 quarters =

$1.75


SPECIAL CYCLE PRICE (DRYER)

Represents the number of quarters (coin 1) to start the dryer; may adjust from 0–39.

(See VALUE OF COIN 1).

• Advance from 0–39 by pressing the upper-left

(COTTON/WHITES) button. Factory default of

6 quarters = $1.50.


SPECIAL DRY TIME (DRYER)

Represents the number of minutes per quarter

(coin 1).

• Factory default of 5 minutes per coin.

Example: 6 quarters x 5 minutes = 30 minutes.

• By pressing the upper-left (COTTON/WHITES) button, the value can be adjusted from 1–99 minutes.


TIME-OF-DAY CLOCK, MINUTES

This is the TIME-OF-DAY CLOCK, minute setting; select 0–59 minutes by pressing the lower-left (HOT) button.


TIME-OF-DAY CLOCK, HOURS

NOTE: Uses military time or 24 hr. clock.

This is the TIME-OF-DAY CLOCK, hour setting; select 0–23 hours by pressing the lower-left (HOT) button.


SPECIAL PRICE START HOUR


This is the start hour; 0–23 hours.

• Select START HOUR by pressing the lower-left

(HOT) button.


SPECIAL PRICE STOP HOUR


This is the stop hour; 0–23 hours.

• Select STOP HOUR by pressing the lower-left

(HOT) button.



9. 10 SPECIAL PRICE DAY

9. 10 This represents the day of the week and whether special pricing is selected for that day. A number followed by “0” indicates no selection that particular day (9.10). A number followed by an “S” indicates selected for that day (9.1S). To change the value of “0” and “S,” use the lower-right

(COLD) button. Days of the week (1–7) are selected by pressing the lower-left (HOT) button.

When exiting set-up code “9,” the display must show the current day of week:

DISPLAY DAY OF WEEK CODE (selected)

10

20

30

40

50

60

70

Day 1=Sunday

Day 2=Monday

Day 3=Tuesday

Day 4=Wednesday

Day 5=Thursday

Day 6=Friday

Day 7=Saturday 7S


1S

2S

3S

4S

5S

6S

A. 00 VAULT VIEWING OPTION

This option is either NOT SELECTED “00” or SELECTED “SC.”

A. 00

A. SC b. 05 b. 05

C. 20

C. 20

E. 00

E. 00

E. AC


Selected “SC.”

• Press the lower-right (COLD) button once for this selection. When selected, the money and/or cycle counts will be viewable (if counter option(s) is selected) when the coin box is removed.


VALUE OF COIN 1

This represents the value of coin 1 in number of nickels: 05 = $0.25.

• By pressing the lower-left (HOT) button, there is an option of 1–199 nickels.


VALUE OF COIN 2/VALUE OF DRYER

TOP OFF

This represents the value of coin 2 in number of nickels: 20 = $1.00.


ADD COINS OPTION

This option is either NOT SELECTED “00” or

SELECTED “AC.” This option causes the customer display to show the number of coins (coin 1) to enter, rather than the dollars-and-cents amount.


Selected “AC.”


3 consecutive times for this selection.


36



F. 00

F. 00

F. CP

ENHANCED PRICING OPTION (WASHER)

Not Selected “OFF.”

Cycle-Based pricing enabled. This option allows configuration of different prices for cold, warm, and hot water cycles.

• Press the lower-right (COLD) button for this selection.


J. Cd PAYMENT MODE (COIN/DEBIT OPTION)

J. Cd

J. C_

Both coin and debit selected. Press the lower-right (COLD) button 3 consecutive times to change this selection.

Coins selected, debit disabled. Press the lower-right (COLD) button 3 consecutive times to change this selection.

J._d Debit Card selected,

J. Ed coins disabled. Press the lower-right (COLD) button

3 consecutive times to change this selection.

Enhanced Debit is self-selected when a Generation

2 card reader is installed in the washer/dryer.

The Ed option cannot be manually selected or deselected.


L. 00

L. 00

L. PS n. CE

PRICE SUPPRESSION OPTION

This option causes the customer display to show

“ADD” or “AVAILABLE” rather than the amount of money to add. (Used mainly in debit installations.)


Selected “PS.”



CLEAR ESCROW OPTION

When selected, money held in escrow for 30 minutes without further escrow or cycle activity will be cleared.

n. 00 n. CE


Selected “CE.”




U. 00 PENNY INCREMENT OFFSET (WASHER)

U. 00

U.00

U.00

This represents the penny increment price offset used with Generation 2 (Enhanced Debit) Models.

Choose from 0–4 pennies by pressing the lowerleft (HOT) button.


PENNY INCREMENT OFFSET (DRYER)

A1. 00

A1. 00

This represents the penny increment price offset used with Generation 2 (Enhanced Debit) Models.

Choose from 0–4 pennies by pressing the upperleft (COTTON/WHITES) button.


PREWASH LENGTH (WASHER)

This is the number of minutes of PREWASH.

Choose 0 to disable the prewash or select between

2 and 7 minutes by pressing the lower-left (HOT) button.


END of SET-UP PROCEDURES.

EXIT FROM SET-UP MODE

• Turn service switch key clockwise and remove or remove manual set-up card.

37

Instructions. Whirlpool CGT8000XQ

General Washer/Dryer User Information

Control Set-up Procedures

There are four (4) types of dryer pricing:

Fixed “Vend” Pricing

Accumulator Pricing

Fixed Cycle With Top Off Pricing

top off price

full cycle price

How to Use the Buttons to Program the Controls

Start Operating Set-up

Set-Up Codes

If money counter (1.0C or 1.C0) is selected, the following is true:

OPTIONS 3.XX – 9.XX TO USE IF SPECIAL PRICING

IS SELECTED

Related manuals

Table of contents

Instructions. Whirlpool CGT8000XQ

General Washer/Dryer User Information

Control Set-up Procedures

There are four (4) types of dryer pricing:

Fixed “Vend” Pricing

Accumulator Pricing

Fixed Cycle With Top Off Pricing

top off price

full cycle price

How to Use the Buttons to Program the Controls

Start Operating Set-up

Set-Up Codes

If money counter (1.0C or 1.C0) is selected, the following is true:

OPTIONS 3.XX – 9.XX TO USE IF SPECIAL PRICING

IS SELECTED

Related manuals

Maytag Commercial

MLE20PDCYW

Whirlpool

CGT8000XQ0

Maytag Commercial

MLE22PRAYW

Maytag

MLG20PDAWW0

Whirlpool

CET8000AQ0

Maytag

MLG20PDAWW0

Whirlpool

WET4124HW

Maytag

MLE20PDCYW0

Whirlpool

CET9000GQ0

Whirlpool

CGT9000GQ

Whirlpool

CET9000GQ

Table of contents