advertisement
CFN III Quick Reference
Switches
Switch settings should be changed with the power switch OFF. The new settings are read by the CPU board when the power is turned ON again.
Switch Bank 1
Position & Definition
1 baud rate
2
3-4 lead detect delay
5 ----
6 authorization activates
7
8 communication mode totalizers
----
Setting(*=customary)
*open=9600
closed=1200
*open=on-line
closed =standalone see below
*open=no
closed=yes
*open=no
closed=reset
Delay Time
0
4
5
6
1-3 closed closed open open
Switch Bank 2
This bank serves two purposes:
1-4 closed open closed open
• address setting when communicating on the
Gasboy RS-485/RS-422 loop, or
• pulser output rate selector when pulser data is sent to a fuel management system other than a
Gasboy CFN.
Pulse Rate 2-1 2-2 2-3
1
10
100
250
500
1000 none none cl op cl op cl op cl op cl cl op op cl cl op op cl op op cl cl cl op op
Address
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
2-1 cl op cl op cl op cl op cl op cl op cl op cl op
LCD Board
Jumpers
Display Address:
Hose
1
2
Jumper Pins across 1 and 2 across 2 and 3
2-2 cl cl op op cl cl op op cl cl op op cl cl op op
2-3 op op op op cl cl cl cl op op op op cl cl cl cl
Display of Units:
Units K2 K4 K6 whole units tenths - .0 hundredths - .00
1-2
2-3
1-2
1-2
1-2
1-2
2-3
1-2
1-2
1-2
1-2
2-3 thousandths - .000
For decimal point position only. Display also depends on pulse rate (latest software) for stand alone mode. Unused digits are marked.
2-4 op op op op op op op op cl cl cl cl cl cl cl cl
Page 48 MDE-4483 CFN III Quick Reference Guide v3.3 · August 2005
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 CONTENTS
- 5 Command Summaries, Version
- 21 FRED Command Summary
- 21 System Variables
- 22 CFN3 Backup
- 23 CFN3 CPU Board
- 23 Switches
- 24 Jumpers
- 24 CFN3 Memory Board
- 24 Switches
- 24 Jumpers
- 24 CFN3 Memory Map
- 25 LED Diagnosis
- 25 Serial/Parallel Ports
- 25 CFN3 Ports
- 26 Internal Profit Point setup
- 26 Diagnostic Error Codes
- 26 Console
- 26 Card & Gate Reader
- 26 Pump Control Unit
- 27 Tank Monitor
- 27 Raw Mode Error Codes
- 27 Profit Point
- 27 Back panel
- 27 Scanner
- 28 Menu Tree
- 29 Menu Tree – Profit Point v
- 31 Special functions
- 31 Check Point
- 31 Special Functions
- 32 Product Attributes
- 32 Check Point Key Map
- 33 Check Point Key Actions
- 34 Switch Settings
- 34 CPU Board, Firmware
- 34 Check Point Test Mode
- 34 Configuration
- 35 Vacuum Fluorescent Display
- 36 Standalone Receipt Printer
- 36 Epson
- 36 Self Test
- 36 Star (RS-422)
- 37 Star (RS-232) for CheckPoint
- 37 Star (Parallel)
- 37 Okidata 184/186 Printer Setup
- 37 Settings for serial printer
- 38 Printer Controls
- 38 Name on Receipt Track 1 only
- 38 POS Reports
- 38 Tender Codes
- 39 Event Codes
- 39 Record Identifiers
- 40 Sample Commands
- 40 Link Terminal Setup
- 41 Island Card Reader I
- 41 CPU Board
- 41 Switches
- 41 Jumpers
- 42 Test Mode
- 42 Printers
- 42 Island Card Reader II
- 42 CPU Board
- 42 Switches
- 43 Jumpers
- 43 Test Mode
- 43 Printers
- 43 Keypad
- 44 Switches
- 45 Jumpers
- 45 CRIND
- 45 Keypad
- 46 Cabling
- 46 D-Box to Gilbarco Interface
- 46 SDI/Wayne CAT
- 46 Keypad
- 47 SDI Box Switches
- 47 Insight Interface
- 47 PC Connection
- 47 Insight Board Switches
- 48 Parameter File
- 48 Parameter File Defaults
- 49 Softkey and Animation sequences
- 49 Pump Control Unit
- 49 EXPMUX CPU Board
- 49 Switches
- 50 Jumpers
- 50 CMOS CPU Board
- 50 Switches
- 50 Jumpers
- 51 I/O Board
- 51 Jumpers
- 51 9800 Pump Dispenser
- 51 CPU Board
- 51 Jumpers
- 51 LED Indicators
- 51 Test Points
- 52 Switches
- 52 LCD Board
- 52 Jumpers
- 53 Electronic Pump Interfaces
- 53 Tokheim
- 54 Gilbarco Interface Unit
- 54 CPU Board
- 55 Front Panel LEDs
- 55 Interface Board
- 56 Wayne
- 57 Tank Gauge
- 57 Veeder-Root CPU Board
- 57 TLS 250 and TLS 250i
- 57 TLS 350R
- 58 Gasboy Interface Software
- 58 422/485 Line Monitor
- 58 PC Monitor
- 58 DIP Switch Banks 2 and
- 58 422/485-232 Converter
- 58 Jumpers
- 59 R1 - Adjusting
- 59 Modems and Cables
- 59 PC Package/Answer modem
- 59 Bank Network modem
- 60 CFN3 to Modem
- 60 CFN3 to Okidata
- 60 RS-232 Character Framing
- 60 Print Transaction
- 60 Host-Site Mode
- 60 Completed Transaction Codes
- 60 Site-Host Mode
- 61 Raw Mode
- 61 PC/Site Control
- 61 Required Settings for CFN
- 61 Command Line Options
- 62 Input and Output Redirection
- 62 Fuel Point Reader
- 62 CPU Board
- 62 Switches
- 63 Site Notes