- Home
- Domestic appliances
- Large home appliances
- Dishwashers
- Jackson
- DynaStar Series High Temperature Door Type Dishwasher
- User Guide
DISPLAY INSTRUCTIONS. Jackson DynaStar Series High Temperature Door Type Dishwasher, DynaStar Series
Add to My manuals64 Pages
advertisement
OPERATION
DISPLAY INSTRUCTIONS
SETTING CYCLES
Press and release the I Button to set cycle 1.
Press and release the II Button to set cycle 2.
Press and release the III Button to set cycle 3.
CHECKING
CYCLE COUNT
While the machine is powered off, press and hold the Power Button. The total cycle count will display for several seconds, followed by a “power-on” condition.
GENERAL
1. When the machine is first connected to the power mains, the display will go through a sequence to show all LEDs are working.
2. The machine will then go into standby mode with the display turned off.
3. Press the Power Button.
4. The display will show “Heating” until the wash tank reaches the set temperature.
Cycle Light
Delime Button
1 2 5 F
H E A T I N G
C Y C L E 1
Power Button
Cycle Buttons
5. The display will show “Ready” when the machine is ready to use.
1 5 0 F
R E A D Y
C Y C L E 1
OPERATIONAL
MESSAGES
DISPLAY INDICATOR
"Check for open door" Door is open when the machine needs to fill (float switch is down).
"Filling"
"Heating"
"Delime"
"Ready"
"Washing"
"Rinsing"
"Sanitizing"
Indicates the initial fill after the machine is first powered on.
The wash tank and booster have not reached operating temperature during the machine’s initial heating phase.
The Delime Button has been pressed.
The machine is not in a cycle and ready for the next load.
The machine is in the wash phase of a cycle with power to the wash pump.
The machine is in the rinse phase of a cycle with power to the rinse valve; wash pump is turned off.
The machine is in the sanitizing phase of a cycle. Neither wash pump nor rinse valve are turned on.
07610-004-66-53-D 18
advertisement
Related manuals
advertisement
Table of contents
- 5 NOMENCLATURE
- 6 TABLE OF CONTENTS
- 8 GUIDES
- 9 SPECIFICATIONS
- 9 MACHINE DIMENSIONS
- 11 TABLE DIMENSIONS
- 12 OPERATING CAPACITIES
- 13 ELECTRICAL REQUIREMENTS
- 14 INSTALLATION
- 14 INSPECTION
- 14 UNPACKING
- 14 LEVELING
- 14 PLUMBING
- 14 DRAIN LINE CONNECTION
- 15 WATER SUPPLY CONNECTION
- 15 PLUMBING CHECK
- 16 CHEMICAL CONNECTIONS
- 17 ELECTRICAL POWER CONNECTIONS
- 17 MOTOR ROTATION
- 18 VOLTAGE CHECK
- 18 SURROUNDING AREA
- 18 TEMPERATURE SETPOINTS
- 19 OPERATION
- 19 PREPARATION
- 19 POWER UP
- 19 FILLING THE WASH TUB
- 20 WARE PREPARATION
- 20 DAILY MACHINE PREPARATION
- 20 WASHING A RACK OF WARE
- 21 TURBO RINSE
- 21 SHUTDOWN & CLEANING
- 23 DETERGENT CONTROL
- 24 DELIMING
- 25 DISPLAY INSTRUCTIONS
- 25 SETTING CYCLES
- 25 CHECKING CYCLE COUNT
- 25 GENERAL
- 25 OPERATIONAL MESSAGES
- 26 MAINTENANCE
- 26 PREVENTATIVE MAINTENANCE
- 26 PSI CHECK
- 27 TROUBLESHOOTING
- 27 PROGRAMMING
- 29 FAULT CODES
- 32 TROUBLESHOOTING
- 34 PARTS
- 34 CONTROL PANEL, 208-230 V
- 36 CONTROL PANEL, 460 V
- 38 HOOD
- 40 CANTILEVER ARM
- 42 TUB
- 44 FRAME
- 46 WASH & RINSE ARMS
- 47 RINSE TANK
- 48 HEATERS
- 49 MOTORS
- 51 DYNASTAR PLUMBING
- 53 DYNASTAR NB PLUMBING
- 55 DYNASTAR VER PLUMBING
- 57 VER SYSTEM
- 58 DOOR INTERLOCK
- 60 PLUMBING OPTIONS
- 61 SCHEMATICS
- 61 DYNASTAR/DYNASTAR VER 208/230 V
- 62 DYNASTAR NB 208/230 V
- 63 ADDENDUM
- 63 DISPLAY GUIDE