Software Installation. D-Link DCS-5605/5635

Section 2 - Installation

Software Installation

Turn on the computer and Insert the D-Link DCS-5605/5635 Driver CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows ® XP. The steps and screens are similar for the other Windows operating systems.

Click Setup Wizard

If the CD Autorun function does not automatically start on your computer, click Windows Start > Run. In the Run command box type “ D:\DCS-56055635.exe

”, where D: represents the drive letter of your CD-ROM. If it does start, proceed to the next screen.

D-Link DCS-5605/5635 User Manual 15


Click Next to continue.

Click Next

Click Yes to accept the License Agreement.

Click Yes



To start the installation click Next .

Note: The installation may take several minutes to complete.

Click Next



Click finish to complete the installation.

Click finish



Now, click on ffdshow from the autorun screen. This will install the proper codecs that will allow you to playback video taken by the DCS-5605/5635.

Click ffdshow

Click I Agree



Select Language, and then click OK.

Click OK

Click Next



Click Next

Click Next



Click Next

Click Next



Click Next

Click Next



Select the speaker from your PC, and then click Next.

Click Next

Click Install



Installing

Click finish


Section 3 - Configuration

Enabling UPnP for Windows ® XP

UPnP (Universal Plug and Play) is a networking architecture that provides compatibility among networking equipment, software, and peripherals. The

DCS-5605/5635 is an UPnP enabled Internet camera. If your operating system is UPnP enabled, the device will be easier to configure. If you do not want to use the UPnP functionality, it can be disabled by unchecking the Enabled UPnP checkbox on the Setup > Network Setup page. Use the following steps to enable UPnP settings only if you are running Windows ® XP. If you are running

Windows ® 98/2000, UPnP is not available.

Go to Start > Settings . Click Control Panel .

Click Add or Remove Programs



Click Add/Remove Windows Components

The following screen will appear.

Select Networking Services.

Click Details

Select Universal Plug and Play.

Click OK



Click Next

Please wait while Setup configures the components.

Click finish



To view your DCS-5605/5635 Internet Camera in an Internet browser, go to your Desktop and click My Network Places .

Click DCS-5605/5635 (192.168.0.120).

D-Link DCS-5605/5635 User Manual

DCS-5635 (192.168.0.120)

29


After you click on the DCS-5605/5635 icon, your Internet browser will automatically be opened to the IP Address of the

DCS-5605/5635, in this example it is: http://192.168.0.120. Your DCS-5605/5635 may have a different IP Address.

http://192.168.0.120/eng/index.cgi



Configuration

This section will show you how to configure your new D-Link Network Camera using the Setup Wizard.

Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu.

Click D-Link Setup Wizard SE



The Setup Wizard will appear and show the MAC address of the

DCS-5605/5635 and an IP Address (which may or may not be correct depending on what you have your DCS-5605/5635 connected to).

If you have a DHCP server on your network, there will be a valid IP

Address displayed here. Click the Wizard button to continue.

Note: A DHCP server is a device that supplies the IP address.

00.1c.f0.d3.fb.0e 192.168.0.185 DCS-5635

Enter the admin ID and password.

Note: The default Admin ID is admin with the password left blank.

Click Next



Select DHCP if you want to obtain a new IP address every time the camera boots up.

Click Next

Select static IP to use the same IP address at each boot up.

Click Next



Click Restart to save your settings and reboot the Network Camera.

Click Restart

Click the button labeled Link to access the web configuration page. The Setup Wizard will automatically open your web browser to the IP address of the DCS-5605/5635, in this example it is: http://192.198.0.185. Your DCS-5605/5635 may have a different

IP Address.

Click Link

00.1c.f0.d3.fb.0e 192.168.0.185 DCS-5635



Web-based Configuration Utility

This section will show you how to configure your new D-Link Network Camera using the Web-based Configuration

Utility.

To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address for your Network Camera (http://192.168.0.185)

Note: For example, the address is 192.168.0.185. Your address may differ.

192.168.0.185

Enter Admin for the username and then leave the password blank by default.

Note: To change your password at a later time, please refer to page 64.

192.168.0.185

Click OK



Setting up a Wireless Connection with WPS

If your wireless access point or router supports push-button Wireless Protected Setup (WPS), you can quickly configure your wireless network and camera without using the camera’s web interface.

After plugging the power adapter to your camera and the front status LED lights up, hold down the WPS button on the back of the camera for 3 seconds. After pressing the button, it should start flashing blue.

Now press the WPS button on your router or access point within 1 minute to activate WPS and allow your devices to automatically configure a wireless connection. After WPS is successfully activated, the WPS LED on your camera will stop flashing, and will light up solid blue, then reboot.

Note: On some routers/access points, you may need to enter the web interface to activate WPS. Consult your product’s user manual for further assistance.

WPS Button

Press this button to establish a WPS connection.



Testing the DCS-5605/5635

Open your Internet browser and type in the IP address of the DCS-5605/5635. In this example, the address is: http://192.168.0.120 (your DCS-5605/5635 may have a different IP address based on what you used in the Setup

Wizard SE program).

The window in the center of your browser is the camera image window. You should now see a video image and hear the audio over your computer speakers from the DCS-5605/5635. If you are having problems, please consult the

Troubleshooting section of this manual (page 89).



Viewing Your DCS-5605/5635

After all the router settings have been entered correctly, a PC user inside or outside your network will have access to the camera through the Internet Explorer Web browser. To access the camera from the Internet, type the IP Address of the router given to you by your ISP, followed by a colon, and the port number that you gave your camera (e.g., http://70.42.15.9:83). It is not necessary to enter the colon and port number if you are using the default Web server port 80. To access from a computer on your local (home) network, simply enter the local IP Address of the Camera followed by a colon and the port number (e.g., 192.168.0.120:83).

If you are following this manual in the order it is presented, you should now have an operating DCS-5605/5635 Internet

Camera configured with the Installer program. This section of the manual will cover how to use the Internet Camera in two methods:

• Using the DCS-5605/5635 with an Internet browser and accessing the screens to control and monitor the camera.

• Using IP surveillance software with the

DCS-5605/5635.



Using the DCS-5605/5635 with an Internet Browser

Open your Internet Explorer Web browser and enter the IP address for your Internet Camera (http://192.168.0.120).

In the example, this address is 192.168.0.120. Your address may differ.

If a window appears asking to install a Verisign certificate for authentication click Yes . This allows the proprietary

MPEG4 video stream to be recognized by Internet Explorer.


Software Installation. D-Link DCS-5605/5635

Software Installation

Enabling UPnP for Windows ® XP

Configuration

Web-based Configuration Utility

Setting up a Wireless Connection with WPS

Testing the DCS-5605/5635

Viewing Your DCS-5605/5635

Using the DCS-5605/5635 with an Internet Browser

Related manuals

Table of contents

Software Installation. D-Link DCS-5605/5635