advertisement
L
I
S
H
E
N
G
31
Installation Guide
WARNING
This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product.
Any attempt to install this product in a motor car by anyone other than a qualifi ed installer could cause damage to the electrical system and could result in serious personal injury or death.
If your car is equipped with air bags and/or anti-theft systems specifi c procedures may be required for connection and disconnection of the battery to install this product.
Before attempting installation of this electronic component contact your car dealer or manufacturer to determine the required procedure and strictly follow their instructions.
FAILURE TO FOLLOW THE PROCEDURE
MAY RESULT IN THE UNINTENDED
DEPLOYMENT OF AIR BAGS OR
ACTIVATION OF THE ANTI-THEFT
SYSTEM RESULTING IN DAMAGE TO
THE VEHICLE AND PERSONAL INJURY.
Caution:
≥
This unit operates with a 12 V DC negative ground auto battery system only.
Do not attempt to use it in any other system.
Doing so could cause serious damage.
Installation Hardware
No.
Item
1 Mounting collar
Diagram Q’ty
1
2 Hex. nut (5 mm
‡
)
3 Rear support strap
4 Tapping screw
(5 mm
‡k
16 mm)
5 Mounting bolt
(5 mm
‡
)
6 Power connector
7
Trim plate
8 Lock cancel plate
1
1
2
1
1
1
1
Required Tools
You’ll need a screwdriver, a 1.5 V AA battery, and the following:
12 V DC
Test bulb
Electrical tape Side-cut pliers
50
CQ-C5410/5310/5210/5110U
Overview
This product should be installed by a professional.
However, if you plan to install this product yourself, your fi rst step is to decide where to install it. The instructions in these pages will guide you through the remaining steps:
(Please refer to the “WARNING” statement.)
≥
Identify and label the car wires.
≥
Connect the car wires to the wires of the power connector.
≥
Install the unit in the dashboard.
≥
Check the operation of the unit.
If you encounter problems, please consult your nearest professional installer.
Before you begin installation, look for the items which are packed with your unit.
≥
Warranty Card
... Fill this out promptly.
≥
Panasonic Servicenter List for Service
Directory
... Keep for future reference in case the product needs servicing.
≥
Installation Hardware
... Needed for in-dash installation.
Dashboard Specifi cations
Thickness Min.
3
/
16 q
(4.75 mm)
Max.
7
/
32 q
(5.56 mm)
2 3 /
32 q
(53 mm)
7 5 /
32 q
(182 mm)
Preparation
≥
We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
≥
When bending the mounting tabs of the mounting collar with a screwdriver, be careful not to injure your hands and fi ngers.
≥
Disconnect the cable from the negative battery terminal (see caution below).
≥
Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30 o
.
L
I
S
H
E
N
G
32
Less than 30 o
Caution:
≥
If your car is equipped with air bags and/or anti-theft systems specifi c procedures may be required for connection and disconnection of the battery to install this product.
≥
Before attempting installation of this electronic component contact your car dealer or manufacturer to determine the required procedure and strictly follow their instructions.
≥
FAILURE TO FOLLOW THE PROCEDURE MAY
RESULT IN THE UNINTENDED DEPLOYMENT
OF AIR BAGS OR ACTIVATION OF THE
ANTI-THEFT SYSTEM RESULTING IN DAMAGE
TO THE VEHICLE AND PERSONAL INJURY.
Note:
≥
Various settings that have been stored in the memory in other on-board equipment (car navigation etc.) may be lost if the battery terminals are disconnected.
Therefore, we recommend to make a record of or to back up the settings before disconnecting the terminals.
After completing installation of the main unit, set the equipment again according to the record.
Dashboard Installation
Installation Opening
2 3 /
32 q
(53 mm)
7
5
/
32 q
(182 mm)
This unit can be installed in any dashboard having an opening as shown above. The dashboard should be 3 /
16 q
(4.75 mm)– 7 /
32 q
(5.56 mm) thick in order to be able to support the unit.
CQ-C5410/5310/5210/5110U
51
L
I
S
H
E
N
G
33
Installation Guide
(continued)
Identify All Leads
The fi rst step in installation is to identify all the car wires you’ll use when hooking up your sound system.
As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later.
Note:
≥
Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order.
Power Lead
If your car has a radio or is pre-wired for one:
Cut the connector wires one at a time from the plug
(leaving the leads as long as possible) so that you can work with individual leads.
Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis.
Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug.
Touch one wire at a time until you fi nd the outlet that causes the test bulb to light.
Now turn the ignition off and then on. If the bulb also turns off and on, that outlet is the car power lead.
If your car is not wired for an audio unit:
Go to the fuse block and fi nd the fuse port for radio
(RADIO), accessory (ACC), or ignition (IGN).
Battery Lead
If your stereo unit has a yellow lead, you will need to locate the car’s battery lead. Otherwise you may ignore this procedure. (The yellow battery lead provides continuous power to maintain a clock, memory storage, or other function.)
If your car has a radio or is pre-wired for one:
With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the chassis and checking the remaining exposed wires from the cut radio connector plug.
If your car is not wired for an audio unit:
Go to the fuse block and fi nd the fuse port for the battery, usually marked BAT.
Speakers
Identify the car speaker leads. There are two leads for each speaker which are usually color coded.
A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1.5 V AA battery as follows.
Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead.
If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each.
Antenna Motor
If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire.
Antenna
The antenna lead is a thick, black wire with a metal plug at the end.
52
CQ-C5410/5310/5210/5110U
Connect All Leads
Now that you have identifi ed all the wires in the car, you are ready to begin connecting them to the stereo unit wires. The wiring diagram (page 56) shows the proper connections and color coding of the leads.
We strongly recommend that you test the unit before making a fi nal installation.
You can set the unit on the fl oor and make temporary connections to test the unit. Use electrical tape to cover all exposed wires.
Important:
≥
Connect the red power lead last, after you have made and insulated all other connections.
Ground
Connect the black ground lead of the power connector to the metal car chassis.
Speakers
Connect the speaker wires. See the wiring diagram
(page 56) for the proper hookups. Follow the diagram carefully to avoid damaging the speakers and the stereo unit.
The speakers used must be able to handle more than 50 W of audio power. If using an optional audio amplifi er, the speakers should be able to handle the maximum amplifi er output power.
Speakers with low input ratings can be damaged.
Speaker impedance should measure 4–8
≠
, which is typically marked on most speakers. Lower or higher impedance speakers will affect output and can cause both speaker and stereo unit damage.
Motor Antenna
Connect the car motor antenna lead to the dark blue motor antenna relay control lead.
(Do not confuse the antenna lead with blue/white stripe lead for a power amplifi er.)
Battery
Connect the yellow battery lead to the correct radio wire or to the battery fuse port on the fuse block.
Antenna
Connect the antenna by plugging the antenna lead into the antenna receptacle.
Equipment
Connect any optional equipment such as an amplifi er, according to the instructions furnished with the equipment. Leave about 12 q
(30 cm) of distance between the speaker leads/amplifi er unit and the antenna/antenna extension cord. Read the operating and installation instructions of any equipment you will connect to this unit.
Power
Connect the red power lead to the correct car radio wire or to the appropriate fuse port on the fuse block.
If the stereo unit functions properly with all these connections made, disconnect the wires and proceed to the fi nal installation.
Final Installation
Lead Connections
Connect all wires, making sure that each connection is insulated and secure. Bundle all loose wires and fasten them with tape so they will not fall down later. Now insert the stereo unit into the mounting collar.
Congratulations! After making a few fi nal checks, you’re ready to enjoy your new auto stereo system.
Final Checks
1. Make sure that all wires are properly connected and insulated.
2. Make sure that the stereo unit is securely held in the mounting collar.
3. Turn on the ignition to check the unit for proper operation.
If you have diffi culties, consult your nearest authorized professional installer for assistance.
L
I
S
H
E
N
G
34
CQ-C5410/5310/5210/5110U
53
L
I
S
H
E
N
G
35
Installation Guide
(continued)
54
CQ-C5410/5310/5210/5110U
Remove the Unit
Switch off the power of the unit.
1 Remove the removable face plate. (page 49)
2 Remove the trim plate 7 with a screwdriver.
Screwdriver
7 Trim plate
3 1 Insert the lock cancel plates 8 along the grooves on both sides of the main unit until “click” is heard.
2 Pull out the unit while pushing the plates further inside.
1 Insert.
Insert the tab end in the outer groove.
“Click”
8 Lock cancel plate
L
I
S
H
E
N
G
36
2 Pull out.
4
Remove the unit pulling with both hands.
CQ-C5410/5310/5210/5110U
55
advertisement
Related manuals
advertisement