Common Settings. Canon i-SENSYS MF8540Cdn, i-SENSYS MF8500 series, MF8280, i-SENSYS MF8580Cdw, i-SENSYS MF8200 series, Color imageCLASS MF8280Cw, i-SENSYS MF8280Cw, i-SENSYS MF8550Cdn, Color imageCLASS MF8580Cdw, MF8580

0ALJ-0C0

Common Settings

All the settings about the operation of the paper drawer and the paper feed method are listed with short descriptions. Default settings are marked with a dagger ( ).

NOTE

Settings marked with " *1 " are only available when the optional paper drawer (drawer 2) is attached.

Settings marked with " *2 " are only available for the MF8580Cdw / MF8550Cdn / MF8280Cw.

Settings marked with " *3 " are only available for the MF8580Cdw / MF8550Cdn / MF8540Cdn.

Drawer Auto Selection On/Off

Switch Paper Feed Method

Drawer Auto Selection On/Off

Enable or disable the automatic drawer selection feature for the paper sources. If automatic drawer selection is set to <On> when printing documents, the machine automatically selects a paper source that is loaded with the appropriate paper size. Also, when the paper runs out, this setting enables continuous printing by switching from one paper source to another that is loaded with the same paper size. You can select a function, such as copy or print, to enable this feature.

Copy

Multi-Purpose Tray

Off

On

Drawer 1

Off

On

Drawer 2 *1

Off

On

Printer

Drawer 1

Off

On

Drawer 2 *1

Off

On

Fax *2

Multi-Purpose Tray

Off

On

Drawer 1

Off

On

Drawer 2 *1

Off

On

Other

Multi-Purpose Tray

Off

On

Drawer 1

Off

On

Drawer 2 *1

Off

On

㻠㻥㻝㻌㻛㻌㻢㻣㻢

<Common Settings> the paper source

<Drawer Auto Selection On/Off>

Select <Off> or <On> <Apply>

Select the function Select

Functions

Select the function for which you want to configure automatic drawer selection.

NOTE:

Select <Other> for functions such as printing reports and lists and printing images from a USB memory device.

Paper Sources

Select the paper source for which you want to enable.

NOTE:

<Multi-Purpose Tray> is not displayed if <Printer> was selected on the previous screen ( ). Automatic drawer selection is always enabled for printing on paper fed from the manual feed slot.

Switch of the settings

Select <On> to enable automatic drawer selection for the paper source you selected on the previous screen ( ).

NOTE:

Make sure to select <On> for <Drawer 1> or <Drawer 2>. If <Off> is selected for both drawers, you cannot finish the configuration.

Switch Paper Feed Method *3

Specify this setting when you print a document on paper with logos. To print on paper with logos, you need to change how the paper loaded in the paper source is facing depending on whether you are performing 1- or 2-sided printing. However, if you change the setting to <Print Side Priority>, you can just load the paper face down for both 1- and 2-sided printing. For more information, see

Loading

Preprinted Paper

.

Multi-Purpose Tray

Speed Priority

Print Side Priority

Drawer 1

Speed Priority

Print Side Priority

Drawer 2 *1

Speed Priority

Print Side Priority

<Common Settings> <Switch Paper Feed Method>

<Speed Priority> or <Print Side Priority>

Select the paper source Select

Paper Sources

Select the paper source that you want to change the setting for.

<Speed Priority>

㻠㻥㻞㻌㻛㻌㻢㻣㻢

When using paper that has been preprinted with a logo, you need to change how it is facing when you perform 1sided and 2-sided printing.

NOTE:

We recommend selecting <Speed Priority> if you do not need to consider which side to print on.

<Print Side Priority>

To print on a specific side of paper, you do not need to flip over paper in the paper source whether 1- or 2-sided printing is selected.

NOTE:

If <Print Side Priority> is set for a paper source that is loaded with paper you cannot use for 2-sided printing

(

Paper

), <Speed Priority> is applied to the paper source instead. In this case, you need to load the paper in the same way as when <Speed Priority> is selected (

Loading Preprinted Paper ).

1-sided printing speed may be slower when <Print Side Priority> is selected.

㻠㻥㻟㻌㻛㻌㻢㻣㻢