- No category
![](http://s1.manualzz.com/store/data/002235318_1-f87474692ab24182563786b999729939-128x128.png)
advertisement
![PELLET STOVES USER MANUAL | Manualzz PELLET STOVES USER MANUAL | Manualzz](http://s1.manualzz.com/store/data/002235318_1-f87474692ab24182563786b999729939-360x466.png)
remote Control
The heating power, the desired room temperature and the appliance ignition/switch off, can be adjusted using the remote control.
To ignite the stove, press key 1 for a few seconds; the appliance will automatically enter the ignition phase. it is possible to adjust power by using keys 4 and 5, whereas the desired temperature can be adjusted using keys 2 and 3. To switch the stove off, press and hold key 1 for a few seconds.
type anD replaCement oF batteries
The batteries are housed in the lower part of the remote control.
To replace it remove the battery-holder (as shown in the figure on the back of the remote control), remove or insert the battery following the symbols on the remote control and on the battery.
4
1
3
5
2
if the remote control is off because it has no batteries, the stove can be controlled from the control panel on top of it.
while replacing the battery, pay attention to the polarity by observing the symbol on the inside compartment of the remote control.
For operation, 1 cr2025, 3v lithium buffer battery is required.
The baTTeries used conTain meTals harmful for The environmenT. They musT Therefore be disposed of separaTely in appropriaTe conTainers.
CommissioninG settinGs
Once the power cable at the back of the stove has been connected, move the switch, also located on the back, to (i).
The switch at the back of the stove powers the stove board.
The stove remains off and a first screen appears on the panel reading OFF.
mains FrequenCy 50/ 60hz
in the event the stove is installed in a country with 60hz frequency, the stove will display "frequenza rete errata" ("mains frequency incorrect").
vary the frequency as described below.
cONTrOls prOceDUre
press key 5.
select 50 - 60hz frequency with key 2 -3.
confirm using key 5 and exit the menu by pressing key 1.
26 ENGLISH
aDjustinG time, Day, month anD year
set clock allows to adjust the time and date cONTrOls prOceDUre
press key 5 for a few seconds, until
set CloCk
appears.
Confirm using key 5.
Use key 3 to select the day
.
press key 5.
Use the same procedure (5 to move forward 3 to set) to adjust the hours, minutes, day, month and year.
press key 1 several times to confirm and exit the menu.
Day hours minutes
Date month year set CloCk
mON, TUe, weD, ...sUN
0...23
00...59
1...31
1...12
00...99
aDjustinG lanGuaGe
it is possible to select the preferred language to display the various messages.
cONTrOls prOceDUre
press key 5 for a few seconds, until
set CloCk
appears.
press key 3 twice
until set language appears.
select the language using key 3.
confirm using key 5.
press key 1 several times to confirm and exit the menu.
lanGuaGe
iTaliaN eNglish germaN
FreNch spaNish
ENGLISH 27
advertisement
Related manuals
advertisement
Table of contents
- 4 ENGLISH
- 4 Warnings
- 4 Safety
- 4 Routine Maintenance
- 5 devices
- 5 REFERENCE STANDARDS
- 6 General
- 7 INSTALLATION
- 7 Inserts Installation
- 8 Fumes exhaust system
- 8 General requirements
- 9 Smoke duct
- 11 Chimney
- 11 Chimney caps
- 12 FUMES EXHAUST SYSTEM PRODUCT REQUIREMENTS
- 12 Combustion products outlet quota
- 13 TECHNICAL INSTALLATION DOCUMENTATION
- 14 SOUVENIR and ILENIA spacers
- 14 HOT AIR DUCTING
- 14 Elisir
- 15 SOUVENIR - ILENIA
- 16 GRAZIOSA PLUS & IRMA PLUS
- 16 EMMA PLUS & TOSCA PLUS
- 17 additional thermostat for ducting motor control
- 17 REARMS
- 18 INSTALLING COMFORT MAXI/ COMFORT PLUS
- 18 Assembly with sliding base
- 19 Comfort Plus
- 19 Pedestal assembly (optional):
- 20 Front pellet feeding kit (optional)
- 20 Air circulation pipes
- 22 Insert extraction
- 23 Mounting the frames
- 23 Pellets and feeding
- 24 Control panel
- 24 Display icons key
- 25 General menu
- 25 Basic instructions
- 26 Remote control
- 26 Type and replacement of batteries
- 26 COMMISSIONING settings
- 26 Mains frequency 50/ 60Hz
- 27 Adjusting time, day, month and year
- 27 Adjusting language
- 28 Operation and logic
- 29 additional thermostat (optional)
- 29 user menu
- 29 Display
- 29 Pellet feed adjustment
- 30 V1- Air
- 30 STAND BY
- 31 keys locked
- 32 V2 - Air
- 32 reset
- 32 Enable chrono
- 32 Chrono
- 33 Programming example
- 1 Cleaning And Maintenance
- 1 Cleaning and Maintenance by the user
- 1 Routine maintenance
- 42 Displays
- 43 ALARMS