advertisement
aDDitional thermostat (optional)
The appliance can control the room temperature using an additional external thermostat (optional). after ignition (pressing key 1 or via chrono mode), the stove will work to reach the setting set on the thermostat, displaying
Work
(contact closed). The standard room probe is automatically ignored.
when the room temperature has been reached (open contact) the stove will go to minimum, displaying
moDulate.
TO iNsTall aND eNaBle iT:
a mechanical or digital thermostat is required.
remove the plug from the socket.
referring to the figure to the side, connect the two thermostat wires
(dry contact - not 220 v!) on the relative terminals at the back of the
machine, one is red and the other one is black.
power the stove.
press key 2, setting the temperature on loW.
The stove is now configured correctly.
it will work controlling the additional external thermostat.
installation must be perFormeD by qualiFieD staFF anD/or the manuFaCturer's teChniCal aFter-sales assistanCe there are tWo stove operatinG moDes, WhiCh are DiFFerent aCCorDinG to the stanD- by FunCtion. see “stanD - by” Chapter.
user menu
Display
This menu allows to adjust the brightness of the display. The possible settings range from 00 to 20.
By adjusting it between 00 and 20 the lighting intensity will be adjusted. (00 = minimum brightness 20 = maximum brightness).
cONTrOls prOceDUre
press key 5 for a few seconds, until set CloCk appears.
press key 3 several times until user is displayed.
confirm using key 5.
"Displ
ay" will appear.
Use keys 2 -3 to select the brightness of the display.
press key 5 to confirm and key 1 to return to the previous menus up to the initial status.
pellet FeeD aDjustment
The following menu allows to adjust the percentage of pellet feed.
if the stove has functioning problems owing to the quantity of pellets, adjust pellet feeding directly from the control board.
The problems correlated to the amount of fuel can be divided into 2 categories:
ENGLISH 29
NO FUel:
the stove can never develop a suitable flame, tending to remain very low even at high powers.
at minimum power the stove tends to almost switch-off taking the stove into “
no pellets
” alarm condition.
when the stove displays the “
no pellets
” alarm, there may be non-burned pellets inside the burn pot.
excess FUel:
the stove develops a very high flame even at low power.
the panoramic glass is very dirty, obscuring it almost totally.
the burn pot tends to become encrusted, blocking the holes for air intake due to the excessive pellet feed, as it is only burned partially.
The adjustment to be performed is in percentage. Therefore changing this parameter will lead to a proportional variation of all stove feeding speeds. Feeding is from -20% to +30%.
Follow the procedure on the display to perform the procedure: cONTrOls prOceDUre
press key 5 for a few seconds, until set CloCk appears.
press key 3 several times until user is displayed.
confirm using key 5.
press key 5 until "pellet" appears.
Use keys 2-3 to increase (3) or decrease (2) the load during the wOrK stage.
press key 5 to confirm and key 1 to return to the previous menus up to the initial status.
v1- air
The menu allows to adjust the speed of the front fan in percentage. cONTrOls prOceDUre
press key 5 for a few seconds, until set CloCk appears.
press key 3 several times until user is displayed.
confirm using key 5.
press key 5 until "v1 air" appears.
Use keys 2 -3 to increase (3) or decrease (2)
press key 5 to confirm and key 1 to return to the previous menus up to the initial status.
1
stanD by stanD - by With DiGital thermostat (stanDarD)
sTBy FUNcTiON seT aT ON if the stby function is active (ON), when the stove reaches the set room temperature and exceeds it by 2°c, it will switch off after a default delay time, displaying stand - by.
when the room temperature is 2°c lower than the setting and once the stove has cooled, it will start to work again at the set power and displaying work.
30 ENGLISH
sTBy FUNcTiON seT aT OFF (DeFaUlT seTTiNg) if the stby function is not active (OFF), if the stove reaches the set room temperature, it will go to minimum, modulating and displaying modulate. when the room temperature is below the setting, it will start to work again at the set power and displaying work.
stanD - by With aDDitional thermostat
The sTBy function is used if immediate stove switch-off is required when the set temperature has been reached.
by default the stby function is always set on oFF (light on).
stby FunCtion set at oFF (DeFaUlT seTTiNg) if the sTBy function is not active (OFF), if the stove reaches the set room temperature, it will go to minimum, modulating and displaying
moDulate
. when the room temperature is below the setting, it will start to work again at the set power and displaying
Work
.
stby FunCtion set at on
when the sTBy function is activated (ON), the stove, upon reaching the set room temperature and exceeding it by 2°c, will switch off after a pre-set default delay, displaying stanD - by.
when the room temperature is 2°c lower than the setting, the stove will start to work again at the set power displaying wOrK.
cONTrOls prOceDUre
press key 5 for a few seconds, until set CloCk appears.
press key 3 several times until user is displayed.
confirm using key 5.
Using key 2 or 3 select at ON.
press key 5 several times to reach stanD-by. press key 5 to confirm and key 1 to return to the previous menus up to the initial status. The sTaND-By function is active.
keys loCkeD
The menu allows to lock the display keys (like with mobile phones). with the function engaged, every time a key is pressed, “keys loCkeD” will appear.
cONTrOls prOceDUre
press key 5 for a few seconds, until set CloCk appears.
press key 3 several times until user is displayed.
confirm using key 5.
press key 5 until "keys loCkeD" appears.
Use keys 2 -3 to select enable/disable.
press key 5 to confirm and key 1 to return to the previous menus up to the initial status.
onCe the FunCtion is aCtivateD, use keys 1 anD 5 at the same time to loCk or unloCk the keyboarD
ENGLISH 31
advertisement
Related manuals
advertisement