advertisement
Chapter 1 Introduction
1.8.23 FRM220-FOM04 4xE1/T1 +100M Ethernet Fiber Optical Multiplexer Card
FRM220-FOM04 is a modular design for 4xE1/T1 + Fast Ethernet multi-service to dual strand fiber PDH multiplexer.
FRM220-FOM04 provides E1/T1 transmission transparently and pure 100Mbps Fast Ethernet simultaneously. The fiber optic line is based on the SFP technology that allows the flexible use of Multimode or Single mode lines and enables the support of different wavelengths and distances. The use of bi-directional SFPs maximizes the utilization of the fiber optic line and results in saving line costs. With SNMP and Web-based management in the
FRM220, the Network administrator can monitor, configure and control the activity of each card in the chassis.
Features
• 4 channels unframed E1/T1
• 10/100Base-TX Ethernet
• Auto MDI/MDIX
• Auto-Negotiation or Force mode
• Supports flow control
• Supports 9K jumbo packets
• Supports Link fault pass through (LFP)
• One clear channel RS232 up to 250Kbps(Async)
• 1+1 fiber protection, less than 50ms
• Supports Digital Diagnostics Monitoring Interface (DDMI)
• AIS on signal loss on E1/T1 and fiber port
• Loopback test on Optical, E1/T1, and RS232 ports
• Supports Dying Gasp
• Two row by twelve character LCD/Menu Keys for configuration
• Supports local or remote In-band management
• Monitor and Configuration status by console port and SNMP manager
• Supports Order wire Ear / Microphone port
• Supports On-Line F/W upgrade
Specifications
E1/T1 ports
Bit Rate
Line Code
Line Impedance
E1:2.048 Mb/s , T1: 1.544Mb/s
E1:AMI/HDB3, T1: AMI/B8ZS
E1: Unbalanced 75 ohms (BNC cable)
Receiver sensitivity
“Pulse" Amplitude
Short haul
Nominal 2.37V+/-10% for 75 ohms
“Zero" Amplitude Nominal +/-0.3V
Transmit Frequency Tracking +/-30 ppm
Internal Timing
Jitter Performance
Crystal Oscillator
According to ITU-T G.823
Performance monitoring
Standards
Interface Connectors
Test Loops
According to ITU-T G.821
ITU-T G.703, G.704, G.706 and G.732
RJ-45, BNC
LLB (Local Loop Back)
RLB Back)
Ethernet
Interface Type 10/100Base-TX
Connector RJ-45
Standards
Duplex modes
IEEE 802.3, 802.3u
Full/Half
Indications
Power Input
OP1 Link, OP2 link, E1/T1 Mode/Link/Loopback test, Order wire, LAN Link/Speed.
AC adapter, 12VDC (or with built-in power in CH20 or CH02M)
Temperature
Humidity
0 ~ 60°C (Operating), -10 ~ 70°C (Storage)
10 ~ 90% RH (non-condensing)
This product includes the following models:
FRM220-FOM04 (Fiber Multiplexer Card)
FOM220-FOM04-CH02M (Stand-alone FOM in 2-slot chassis)
32
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Chapter 1 Introduction
- 7 1.0 Introduction
- 7 1.1 Functional Description
- 7 1.2 Chassis Front Description
- 8 1.3 LED Indicators and Alarm Relay
- 8 1.4 Chassis Rear Description
- 8 1.5 Chassis Physical Dimensions
- 9 1.6 Chassis Specifications
- 9 1.7 NMC (SNMP)
- 10 1.8 Line card options
- 10 1.8.1 FRM220-10/100i In-band managed 10/100 Fiber Media Converter
- 11 1.8.2 FRM220-10/100iS-2 Dual Channel In-band managed 10/100 Fiber Media Converter
- 12 1.8.3 FRM220-10/100i-2E In-band managed 10/100 Fiber Media Converter
- 13 1.8.4 FRM220-10/100A(S) 802.3ah In-band managed 10/100 Fiber Media Converter
- 14 1.8.5 FRM220-1000EA(S) 802.3ah In-band managed Gigabit Fiber Media Converter
- 15 1.8.6 FRM220-1000EDS Managed Gigabit Fiber Media Converter
- 16 1.8.7 FRM220-E1/T1 In-band managed G.703 E1/T1(DS1) Fiber Modem
- 17 1.8.8 FRM220-Data In-band managed V.35, X.21, RS-530/449/232 Fiber Modem
- 18 1.8.9 FRM220-Serial/485 In-band managed RS-485/422/232 Fiber Modem
- 19 1.8.10 FRM220-FXO/FXS In-band managed POTS (Voice) over Fiber Modem
- 20 1.8.11 FRM220-155MS SM/MM, MM/SM converter / repeater
- 21 1.8.12 FRM220-2.7G-2S, 2.7Gbps 3R Fiber Transponder
- 22 1.8.13 FRM220-2.7G-3S 3R Transponder with Protection
- 23 1.8.14 FRM220-10G-xx 10Gbps 3R Fiber Transponder
- 24 1.8.15 FRM220-MD40/80 CWDM Mux/DeMux
- 25 1.8.16 FRM220-iMUX Inverse Multiplexer Blades
- 26 1.8.17 FRM220-Eoe1 Ethernet over E1 Converter
- 27 1.8.18 FRM220-E1/Data DSU/CSU Converter Card
- 28 1.8.19 FRM220-FTEC E1/T1 Cross Rate Converter Card
- 29 1.8.20 FRM220-1000TS GbE to Gigabit Fiber Converter Card
- 30 1.8.21 FRM220-4G 2R 4.25G Transponder Card
- 31 1.8.22 FRM220-Serial/FDC RS-485/RS-232 Fiber Ring Converter Card
- 32 1.8.23 FRM220-FOM04 4xE1/T1 +100M Ethernet Fiber Optical Multiplexer Card
- 33 Chapter 2 Installation
- 33 2.1 Introduction
- 33 2.2 Site Preparation
- 33 2.3 Mechanical Assembly
- 33 2.3.1 Rack mounting
- 34 2.3.2 Power/Fan Modules Removal/Replacement
- 34 2.3.3 Line Card Conversion, Stand-alone/Rack
- 35 2.4 Electrical Installation
- 35 2.5 Alarm Installation
- 36 2.6 NMC Card Installation
- 36 2.7 Line Card Installation
- 37 Chapter 3. Management Quick Start
- 37 3.1 Introduction
- 37 3.2 Management Methods
- 37 3.3 Console Terminal
- 37 3.3.1 Terminal Connection & Settings
- 37 3.3.2 Terminal Login
- 38 3.3.3 TCP/IP Setup
- 38 3.3.4 Test TCP/IP Connection
- 39 3.4 Telnet Terminal
- 39 3.5 Web Based Manager
- 40 3.6 Element Management System (EMS)