- No category
advertisement
16.2 Typical system (fig. 3)
1 . Signo
2 . Aluminium bar
3 . Key-operated selector switch
4 . Post for selector switch
5 . Post for photocells
6 . Photocell
7 . Red rubber protective strip
8 . Safety edge or red rubber strip
9 . Flashing signal lights
10. Red reflector strips
11. Aerial
12. Flashing light
16.3 Fixing
11. Embed the supplied foundation plate in a suitably sized concrete plinth. The plate must be flush with the surface of the plinth, perfectly level, and with the exposed surface perfectly clean, taking care not to damage the thread of the anchor fixings and providing the facility for at least one or more ducts for the routing of electrical cables.
Warning: the plate must be parallel to the bar.
Fig. 4
12. Place SIGNO on the previously installed base and secure it with the supplied screws and washers.
Fig. 5
13. If necessary, invert the position of the spring, moving it from the right to the left. Warning: the bar will be positioned vertically when the spring is in its relaxed position.
Fig. 6
14. Fit the bar with the specific bracket supplied and secure it by tightening the 4 screws.
15. Perform the release procedure (see chapter 8 "Manual or release procedure”)
Fig. 7
16. Bring the bar to its horizontal position and fit any optional accessories required.
17. Balance the bar by means of the spring adjuster tension rod. The bar can be considered to be properly balanced when, positioned at an angle of 45°, it neither tends to descend nor move upwards.
Fig. 8
WARNING: once the balancing procedure is terminated tighten the tension rod nuts.
18. Horizontal and vertical linear alignment can be adjusted by means of the travel limit cushioning devices
Fig. 9
19. Relock the barrier by performing step 5 in reverse.
20. If the SIGNO accessories are not used or only certain accessories are used, the balancing procedure can be facilitated by fixing the spring in one of the available holes
Fig. 10
16.4 Connection to the power supply
Connect the 230V supply cable directly to the terminal.
Fig. 11
Secure with the specific cable clamp.
28
advertisement
Related manuals
advertisement
Table of contents
- 6 Avvertenze
- 6 Descrizione prodotto
- 7 Limiti d’impiego
- 7 Installazione
- 7 Verifiche e preliminari
- 8 Impianto tipico (fig. 3)
- 8 Fissaggio
- 8 Allacciamento all’alimentazione
- 9 Schema elettrico
- 10 Descrizione dei collegamenti
- 10 Note sui Collegamenti elettrici
- 11 Tipologia dell’ ingresso Alt
- 11 Fototest
- 11 Verifica dei collegamenti
- 12 Programmazione e regolazioni
- 12 Ricerca iniziale degli arresti meccanici
- 13 Ricerca automatica degli arresti meccanici
- 13 Programmazione manuale dei rallentamenti
- 14 Procedura di memorizzazione
- 14 Cancellazione della memoria
- 14 Regolazioni
- 14 Regolazione forza
- 15 Regolazione velocità
- 15 Regolazione tempo pausa
- 15 Collaudo
- 16 Funzioni selezionabili
- 16 Descrizione delle funzioni
- 17 Cosa fare se
- 18 Manovra manuale o sblocco
- 18 Manutenzione
- 18 Pianificazione interventi manutenzione
- 20 Smaltimento
- 20 Caratteristiche tecniche
- 21 Caratteristiche centrale di comando
- 21 Accessori
- 21 Ricevitore RADIO
- 22 Istruzioni ed avvertenze destinate all’utilizzatore della barriera SIGNO
- 26 Warnings
- 26 Product description
- 27 Operating limits
- 27 Installation
- 27 Checks and preliminary operations
- 28 Typical system (fig. 3)
- 28 Fixing
- 28 Connection to the power supply
- 29 Electrical diagram
- 30 Description of connections
- 30 Notes on electrical connections
- 30 Description of the Stop input
- 31 Phototest
- 31 Checking the connections
- 32 Programming and adjustments
- 32 Mechanical stops initial search
- 32 Mechanical stops automatic search
- 33 Manual programming of deceleration positions
- 33 Save procedure
- 34 Memory delete
- 34 Adjustments
- 34 Torque adjustment
- 34 Speed adjustment
- 34 Pause time adjustment
- 35 Testing and commissioning
- 36 Selectable functions
- 36 Functions description
- 37 What to do if
- 38 Manual or release manoeuvre
- 38 Maintenance
- 38 Planning of maintenance work
- 40 Disposal
- 40 Technical specifications
- 40 Control unit specifications
- 41 Accessories
- 41 RADIO receiver
- 42 Instructions and warnings for SIGNO barrier users