- No category
advertisement
To program the STOP input:
4. Set the dip switches as shown
1 2 3 4 5 6 7 8 9 10 11 12
input in teach-in mode.
6. Return the dip switches to the setting indicated
1 2 3 4 5 6 7 8 9 10 11 12
Note. When the programming procedure is terminated the STOP LED must remain illuminated to confirm that the data have been saved correctly.
!
16.9 Phototest
The Phototest function is an ideal solution in terms of reliability in relation to safety devices and it makes it possible to achieve "category 2" in compliance with UNI EN 954-1 (edition 12/1998), in relation to the combination of control unit and safety devices. To implement this solution connect the photocells as shown in the following diagram and set dip switch 7 to On (Phototest activation).
FOTO FOTO
Whenever a manoeuvre is started all the safety devices are tested and the manoeuvre is effectively started only when the test gives positive results.
16.10 Checking the connections.
The following operations involve work being carried out on live circuits. Some parts carry mains voltage and are therefore extremely dangerous! Pay maximum attention to what you are doing and never work alone!
When you have finished making the connections it is good practice to perform a general check as follows:
• Power on the control unit and immediately check for the presence of mains voltage on terminals 1-2 and between 28 and 33 volts on terminals 9-10 (services output). If the values do not correspond to the above specifications, disconnect the unit immediately and check the connections and power supply voltage carefully.
• Approximately 2 seconds after power-on the OK LED should start flashing at regular intervals of one second to indicate that the control unit is functioning correctly.
• Check that the LEDs relative to the STOP and Photo inputs are illuminated (safety devices active), while the LEDs relative to the step-by-step and open/close inputs must be extinguished (no command present); if this is not the case check the connections and ensure that the various devices are functioning correctly
• Check that all the safety devices in the system are functioning correctly (emergency stop, photocells, pneumatic safety edges, etc.); whenever the safety devices trip the relative STOP and Photo LEDs must switch off.
• Release the barrier and check that: the bar is balanced – if it is not, adjust the balancing spring the bar is free to move without undue resistance throughout the entire range of motion the limit switches are functioning correctly: with the bar closed only the closed limit switch LED
31
advertisement
Related manuals
advertisement
Table of contents
- 6 Avvertenze
- 6 Descrizione prodotto
- 7 Limiti d’impiego
- 7 Installazione
- 7 Verifiche e preliminari
- 8 Impianto tipico (fig. 3)
- 8 Fissaggio
- 8 Allacciamento all’alimentazione
- 9 Schema elettrico
- 10 Descrizione dei collegamenti
- 10 Note sui Collegamenti elettrici
- 11 Tipologia dell’ ingresso Alt
- 11 Fototest
- 11 Verifica dei collegamenti
- 12 Programmazione e regolazioni
- 12 Ricerca iniziale degli arresti meccanici
- 13 Ricerca automatica degli arresti meccanici
- 13 Programmazione manuale dei rallentamenti
- 14 Procedura di memorizzazione
- 14 Cancellazione della memoria
- 14 Regolazioni
- 14 Regolazione forza
- 15 Regolazione velocità
- 15 Regolazione tempo pausa
- 15 Collaudo
- 16 Funzioni selezionabili
- 16 Descrizione delle funzioni
- 17 Cosa fare se
- 18 Manovra manuale o sblocco
- 18 Manutenzione
- 18 Pianificazione interventi manutenzione
- 20 Smaltimento
- 20 Caratteristiche tecniche
- 21 Caratteristiche centrale di comando
- 21 Accessori
- 21 Ricevitore RADIO
- 22 Istruzioni ed avvertenze destinate all’utilizzatore della barriera SIGNO
- 26 Warnings
- 26 Product description
- 27 Operating limits
- 27 Installation
- 27 Checks and preliminary operations
- 28 Typical system (fig. 3)
- 28 Fixing
- 28 Connection to the power supply
- 29 Electrical diagram
- 30 Description of connections
- 30 Notes on electrical connections
- 30 Description of the Stop input
- 31 Phototest
- 31 Checking the connections
- 32 Programming and adjustments
- 32 Mechanical stops initial search
- 32 Mechanical stops automatic search
- 33 Manual programming of deceleration positions
- 33 Save procedure
- 34 Memory delete
- 34 Adjustments
- 34 Torque adjustment
- 34 Speed adjustment
- 34 Pause time adjustment
- 35 Testing and commissioning
- 36 Selectable functions
- 36 Functions description
- 37 What to do if
- 38 Manual or release manoeuvre
- 38 Maintenance
- 38 Planning of maintenance work
- 40 Disposal
- 40 Technical specifications
- 40 Control unit specifications
- 41 Accessories
- 41 RADIO receiver
- 42 Instructions and warnings for SIGNO barrier users