advertisement
* Ice Fan Scroll Assembly Replacement
1) Remove the plastic guide for slides on left side by unscrewing phillips head screws.
2) Pull the grille forward as shown in the second picture.
3) Disconnect wire harness of the grille
4) Remove the scroll assembly by loosening 2 screws
3-6 LAMP
(1) (2)
Figure 14
3-6-1 Refrigerator Compartment Lamp
1. Unplug Refrigerator, or disconnect power at the circuit breaker.
2. If necessary, remove top shelf or shelves.
3. Using a flat instrument, gently pry the cover loose in the front as shown. Rotate downward to remove rear tabs.4.
Make sure the bulbs are cool to the touch.
Turn bulbs counterclockwise to remove.
5. Assemble in reverse order by snapping the Lamp Cover in, engaging the rear tabs followed by the front tabs.
(Max. 60 W-2EA)
(3)
3-5 DEFROST CONTROL ASSEMBLY
(4)
Defrost Control assembly consists of Defrost Sensor and
FUSE–M.
The Defrost Sensor works to defrost automatically. It is attached to the metal side of the Evaporator and senses its temperature. At 72°C, it turns the Defrost Heater off.
Fuse-M is a safety device for preventing over-heating of the Heater when defrosting.
1. Pull out the grille assembly. (Figure 12)
2. Separate the connector with the Defrost Control assembly and replace the Defrost Control assembly after cutting the Tie Wrap. (Figure 13)
GRILLE ASSEMBLY
DEFROST-CONTROL
ASSEMBLY
Figure 15
3-6-2 Freezer Compartment Lamp
1. Unplug refrigerator power cord form outlet.
2. Using a flat instrument, gently pry the lamp cover loose in the front as shown. Rotate downward to remove the rear tabs.
3. Make sure the bulb is cool to the touch. Turn the bulb counterclockwise to remove.
4. Replace with a new 60-watt appliance bulb.
5. Insert tabs on back of cover into slots in freezer ceiling. Push cover up to snap front into place.
3-7 CONTROL BOX-REFRIGERATOR
1. First, remove all shelves in the refrigerator, than remove
Figure 12
Figure 13
CONTROL BOX
- 8 -
COVER LAMP
Figure 16
the Refrigerator control Box by loosening 2 screws.
2. Remove the Refrigerator Control Box by pulling it downward.
3. Disconnect the lead wire on the right position and separate the lamp sockets.
advertisement
advertisement
Table of contents
- 2 SAFETY PRECAUTIONS
- 3 1. SPECIFICATIONS
- 4 2. PARTS IDENTIFICATION
- 5 3. DISASSEMBLY
- 5 REMOVING AND REPLACING REFRIGERATOR DOORS
- 7 TO REMOVE THE DISPENSER
- 7 DOOR ALIGNMENT
- 7 FAN AND FAN MOTOR(Evaporator)
- 8 ICE FAN SCROLL ASSEMBLY REPLACEMENT
- 8 DEFROST CONTROL ASSEMBLY
- 8 CONTROL BOX-REFRIGERATOR
- 9 MULTI DUCT
- 9 MAIN PWB, DISPLAY PWB REPLACEMENT, FUNNEL REPLACEMENT
- 10 REPLACEMENT, ICE MAKER ASSEMBLY
- 11 AUGER MOTOR COVER, AUGER MOTOR REPLACEMENT
- 12 DOOR ICE BIN
- 13 HOW TO REMOVE AND REINSTALL THE PULLOUT DRAWER
- 17 4. ADJUSTMENT
- 17 COMPRESSOR
- 17 PTC-STARTER
- 18 OLP(OVERLOAD PROTECTOR)
- 18 TO REMOVE THE COVER PTC
- 19 5. CIRCUIT DIAGRAM
- 20 6. TROUBLESHOOTING
- 20 COMPRESSOR AND ELECTRIC COMPONENTS
- 21 OTHER ELECTRICAL COMPONENTS
- 22 SERVICE DIAGNOSIS CHART
- 23 REFRIGERATION CYCLE
- 25 7. OPERATION PRINCIPLE & REPAIR METHOD OF ICEMAKER
- 28 8. DESCRIPTION OF FUNCTION, CIRCUITS & ERROR CODES