- No category
advertisement
USER MANUAL
Peplink Balance Series
23.4 Access Point
(Available on Peplink Balance 305 and 380+)
The Status of connected access point devices can be found at Status > Access Point.
It lists all connected or detected Pepwave access point devices and their IP address, firmware version, assigned AP profile, number of connected clients and broadcasting channel.
The broadcasting channel follows by a “*” means the channel is automatically chosen and selected by the
Peplink Balance.
23.5 WINS Client
The WINS client list table is located at Status > WINS Client.
It lists WINS client IP addresses and their Names. This option will only be available when you have enabled the WINS Server in section 9.
Name of clients retrieved will be automatically matched into Client List in the previous section.
Click the button Flush All to flush all WINS client records.
23.6 SpeedFusion
TM
Status
(Available on Peplink Balance 210+)
This is a page showing the current status of SpeedFusion
TM
, located at: Status > SpeedFusion
TM
Details about SpeedFusion
TM
connection peers would be shown as below.
You can simply click on the corresponding peer name to explore the WAN connection(s) status and subnet information of each VPN peer.
http://www.peplink.com
-172 / 199 - Copyright © 2013 Peplink
advertisement
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION AND SCOPE
- 6 GLOSSARY
- 7 PRODUCT COMPARISON CHART
- 11 PRODUCT FEATURES
- 11 Supported Network Features
- 12 Other Supported Features
- 14 PACKAGE CONTENTS
- 14 Peplink Balance
- 15 PEPLINK BALANCE OVERVIEW
- 15 Peplink Balance
- 38 INSTALLATION
- 38 Preparation
- 38 Constructing the Network
- 39 Configuring the Network Environment
- 40 BASIC CONFIGURATION
- 40 Connecting to Web Admin Interface
- 41 Configuration with Setup Wizard
- 43 Advanced Setup
- 45 CONFIGURATION OF LAN INTERFACE
- 49 DROP‐IN MODE
- 52 CONFIGURATION OF WAN INTERFACE(S)
- 54 Connection Method(s)
- 60 Physical Interface Settings
- 62 WAN Health Check
- 65 Bandwidth Allowance Monitor
- 66 Additional Public IP Settings
- 67 Dynamic DNS Settings
- 69 Settings
- 73 Peplink Balance Behind NAT Router
- 74 Status
- 75 IPSEC VPN
- 75 IPsec VPN Settings
- 78 IPsec Status
- 78 MANAGEMENT OF OUTBOUND TRAFFIC TO WAN
- 78 Outbound Policy
- 80 Custom Rules for Outbound Policy
- 86 INBOUND ACCESS
- 86 Definition of Port Forwarding
- 88 Definition of Servers on LAN
- 89 Inbound Access Services
- 103 Reverse Lookup Zones
- 106 DNS Record Import Wizard
- 109 NAT MAPPINGS
- 111 WLAN CONTROLLER
- 111 WLAN Information
- 116 AP Management
- 117 Wireless Networks
- 122 Captive Portal Management
- 129 AP Profile
- 132 User Groups
- 133 Bandwidth Control
- 134 Application
- 136 FIREWALL
- 136 Outbound and Inbound Firewall Rules
- 142 Web Blocking
- 143 MISCELLANEOUS SETTINGS
- 143 High Availability
- 146 PPTP Server
- 148 Service Forwarding
- 150 Service Passthrough
- 151 SYSTEM SETTINGS
- 151 Admin Security
- 155 Firmware Upgrade
- 157 Email Notification
- 159 Remote Syslog
- 162 InControl
- 163 Configuration
- 164 Reboot
- 164 TOOLS
- 164 Ping Test
- 166 Traceroute Test
- 166 Test
- 167 CLI (Command Line Interface Support)
- 168 STATUS
- 168 Device
- 169 Active Sessions
- 171 Client List
- 172 Access Point
- 172 WINS Client
- 172 Status
- 173 Event Log
- 174 Bandwidth
- 179 APPENDIX A. RESTORATION OF FACTORY DEFAULTS
- 180 APPENDIX B. ROUTING UNDER DHCP, STATIC IP, AND PPPOE
- 180 Routing via Network Address Translation (NAT)
- 181 Routing via IP Forwarding
- 182 APPENDIX C. CASE STUDIES
- 182 Performance Optimization
- 184 Maintaining the Same IP Address throughout a Session
- 185 Bypassing the Firewall to Access Hosts on LAN
- 186 Inbound Access Restriction
- 187 Outbound Access Restriction
- 188 APPENDIX D. TROUBLESHOOTING
- 190 APPENDIX E. PRODUCT SPECIFICATIONS
- 190 Peplink Balance 20 and
- 191 Peplink Balance 210 and
- 192 Peplink Balance
- 198 APPENDIX F. DECLARATION