- No category
advertisement
USER MANUAL
Peplink Balance Series
Appendix A. Restoration of Factory Defaults
To restore the factory default settings on a Peplink Balance unit, perform the following:
For Balance 20/30/210/310:
1. Locate the reset button on the Peplink Balance unit.
2. With a paper clip, press and keep the reset button pressed for at least 10 seconds, until the unit reboots itself.
For Balance 305/380/580/710/1350:
Use the buttons on front panel to control the LCD menu to go to Maintenance > Factory
Defaults, and then choose Yes to confirm.
Afterwards, the factory default settings will be restored.
Important Note
All user settings will be lost after restoring the factory default settings.
Regular backup of configuration parameters is strongly recommended.
http://www.peplink.com
-179 / 199 - Copyright © 2013 Peplink
advertisement
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION AND SCOPE
- 6 GLOSSARY
- 7 PRODUCT COMPARISON CHART
- 11 PRODUCT FEATURES
- 11 Supported Network Features
- 12 Other Supported Features
- 14 PACKAGE CONTENTS
- 14 Peplink Balance
- 15 PEPLINK BALANCE OVERVIEW
- 15 Peplink Balance
- 38 INSTALLATION
- 38 Preparation
- 38 Constructing the Network
- 39 Configuring the Network Environment
- 40 BASIC CONFIGURATION
- 40 Connecting to Web Admin Interface
- 41 Configuration with Setup Wizard
- 43 Advanced Setup
- 45 CONFIGURATION OF LAN INTERFACE
- 49 DROP‐IN MODE
- 52 CONFIGURATION OF WAN INTERFACE(S)
- 54 Connection Method(s)
- 60 Physical Interface Settings
- 62 WAN Health Check
- 65 Bandwidth Allowance Monitor
- 66 Additional Public IP Settings
- 67 Dynamic DNS Settings
- 69 Settings
- 73 Peplink Balance Behind NAT Router
- 74 Status
- 75 IPSEC VPN
- 75 IPsec VPN Settings
- 78 IPsec Status
- 78 MANAGEMENT OF OUTBOUND TRAFFIC TO WAN
- 78 Outbound Policy
- 80 Custom Rules for Outbound Policy
- 86 INBOUND ACCESS
- 86 Definition of Port Forwarding
- 88 Definition of Servers on LAN
- 89 Inbound Access Services
- 103 Reverse Lookup Zones
- 106 DNS Record Import Wizard
- 109 NAT MAPPINGS
- 111 WLAN CONTROLLER
- 111 WLAN Information
- 116 AP Management
- 117 Wireless Networks
- 122 Captive Portal Management
- 129 AP Profile
- 132 User Groups
- 133 Bandwidth Control
- 134 Application
- 136 FIREWALL
- 136 Outbound and Inbound Firewall Rules
- 142 Web Blocking
- 143 MISCELLANEOUS SETTINGS
- 143 High Availability
- 146 PPTP Server
- 148 Service Forwarding
- 150 Service Passthrough
- 151 SYSTEM SETTINGS
- 151 Admin Security
- 155 Firmware Upgrade
- 157 Email Notification
- 159 Remote Syslog
- 162 InControl
- 163 Configuration
- 164 Reboot
- 164 TOOLS
- 164 Ping Test
- 166 Traceroute Test
- 166 Test
- 167 CLI (Command Line Interface Support)
- 168 STATUS
- 168 Device
- 169 Active Sessions
- 171 Client List
- 172 Access Point
- 172 WINS Client
- 172 Status
- 173 Event Log
- 174 Bandwidth
- 179 APPENDIX A. RESTORATION OF FACTORY DEFAULTS
- 180 APPENDIX B. ROUTING UNDER DHCP, STATIC IP, AND PPPOE
- 180 Routing via Network Address Translation (NAT)
- 181 Routing via IP Forwarding
- 182 APPENDIX C. CASE STUDIES
- 182 Performance Optimization
- 184 Maintaining the Same IP Address throughout a Session
- 185 Bypassing the Firewall to Access Hosts on LAN
- 186 Inbound Access Restriction
- 187 Outbound Access Restriction
- 188 APPENDIX D. TROUBLESHOOTING
- 190 APPENDIX E. PRODUCT SPECIFICATIONS
- 190 Peplink Balance 20 and
- 191 Peplink Balance 210 and
- 192 Peplink Balance
- 198 APPENDIX F. DECLARATION