- No category
advertisement
▼
Scroll to page 2
of
199
USER MANUAL
Peplink Balance Series
B.2 Routing via IP Forwarding
When Peplink Balance is operating under IP Forwarding mode, the IP addresses of IP packets are unchanged; Peplink Balance forwards both inbound and outbound IP packets without changing their IP addresses.
The following figure shows the packet flow in IP Forwarding mode:
http://www.peplink.com
-181 / 199 - Copyright © 2013 Peplink
advertisement
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION AND SCOPE
- 6 GLOSSARY
- 7 PRODUCT COMPARISON CHART
- 11 PRODUCT FEATURES
- 11 Supported Network Features
- 12 Other Supported Features
- 14 PACKAGE CONTENTS
- 14 Peplink Balance
- 15 PEPLINK BALANCE OVERVIEW
- 15 Peplink Balance
- 38 INSTALLATION
- 38 Preparation
- 38 Constructing the Network
- 39 Configuring the Network Environment
- 40 BASIC CONFIGURATION
- 40 Connecting to Web Admin Interface
- 41 Configuration with Setup Wizard
- 43 Advanced Setup
- 45 CONFIGURATION OF LAN INTERFACE
- 49 DROP‐IN MODE
- 52 CONFIGURATION OF WAN INTERFACE(S)
- 54 Connection Method(s)
- 60 Physical Interface Settings
- 62 WAN Health Check
- 65 Bandwidth Allowance Monitor
- 66 Additional Public IP Settings
- 67 Dynamic DNS Settings
- 69 Settings
- 73 Peplink Balance Behind NAT Router
- 74 Status
- 75 IPSEC VPN
- 75 IPsec VPN Settings
- 78 IPsec Status
- 78 MANAGEMENT OF OUTBOUND TRAFFIC TO WAN
- 78 Outbound Policy
- 80 Custom Rules for Outbound Policy
- 86 INBOUND ACCESS
- 86 Definition of Port Forwarding
- 88 Definition of Servers on LAN
- 89 Inbound Access Services
- 103 Reverse Lookup Zones
- 106 DNS Record Import Wizard
- 109 NAT MAPPINGS
- 111 WLAN CONTROLLER
- 111 WLAN Information
- 116 AP Management
- 117 Wireless Networks
- 122 Captive Portal Management
- 129 AP Profile
- 132 User Groups
- 133 Bandwidth Control
- 134 Application
- 136 FIREWALL
- 136 Outbound and Inbound Firewall Rules
- 142 Web Blocking
- 143 MISCELLANEOUS SETTINGS
- 143 High Availability
- 146 PPTP Server
- 148 Service Forwarding
- 150 Service Passthrough
- 151 SYSTEM SETTINGS
- 151 Admin Security
- 155 Firmware Upgrade
- 157 Email Notification
- 159 Remote Syslog
- 162 InControl
- 163 Configuration
- 164 Reboot
- 164 TOOLS
- 164 Ping Test
- 166 Traceroute Test
- 166 Test
- 167 CLI (Command Line Interface Support)
- 168 STATUS
- 168 Device
- 169 Active Sessions
- 171 Client List
- 172 Access Point
- 172 WINS Client
- 172 Status
- 173 Event Log
- 174 Bandwidth
- 179 APPENDIX A. RESTORATION OF FACTORY DEFAULTS
- 180 APPENDIX B. ROUTING UNDER DHCP, STATIC IP, AND PPPOE
- 180 Routing via Network Address Translation (NAT)
- 181 Routing via IP Forwarding
- 182 APPENDIX C. CASE STUDIES
- 182 Performance Optimization
- 184 Maintaining the Same IP Address throughout a Session
- 185 Bypassing the Firewall to Access Hosts on LAN
- 186 Inbound Access Restriction
- 187 Outbound Access Restriction
- 188 APPENDIX D. TROUBLESHOOTING
- 190 APPENDIX E. PRODUCT SPECIFICATIONS
- 190 Peplink Balance 20 and
- 191 Peplink Balance 210 and
- 192 Peplink Balance
- 198 APPENDIX F. DECLARATION