advertisement
▼
Scroll to page 2
of 64
Click Send Message, input message in the popup, and then click Send.
5.2 Send SMS & Receive SMS
The DWG2000-1G can be used to send messages and receive massages.
5.2.1 Configuration Procedures for Sending SMS
Step 1. In the navigation on the left, Click Mobile Configuration Send SMS.
Step 2. On the displayed configuration interface, configure the following parameters:
DWG2000-1G User Manual
16
Copyright @ 2011-2015 Dinstar
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 1 Product Description
- 7 1.1 Overview
- 7 1.2 Application Scenario
- 8 1.3 Product Appearance
- 8 1.3.1 Images of DWG2000-1G
- 9 1.3.2 Indicators and Related Explanation
- 9 1.4 Functions and Features
- 9 1.4.1 Protocols Supported
- 9 1.4.2 System Function
- 10 1.4.3 Industrial Standards Supported
- 10 1.4.4 General Hardware Specifications
- 11 2 Quick Installation
- 11 2.1 Prerequisites
- 11 2.2 Installation Procedures
- 12 3 Web Management System
- 12 3.1 Introduction to Web Management System
- 12 3.1.1 Parts of Web Management Interface
- 12 3.1.2 Login GUI of Web Management Interface
- 13 4 Network Configuration
- 13 4.1 Working Mode of Network
- 13 4.2 Network Configuration under Route Mode
- 14 4.2.1 Network Connection Diagram
- 15 4.2.2 Configuration Procedures on Web Management System
- 17 4.3 Network Configuration under Bridge Mode
- 17 4.3.1 Network Connection Diagram
- 17 4.3.2 Configuration Procedures on Web Management System
- 19 5 Mobile Configuration
- 19 5.1 SMS API
- 19 5.1.1 Introduction to SMS API
- 19 5.1.2 Configuration Procedures for SMS API
- 22 5.2 Send SMS & Receive SMS
- 22 5.2.1 Configuration Procedures for Sending SMS
- 23 5.2.2 Configuration Procedures for Receiving SMS
- 24 5.3 USSD
- 24 5.3.1 Configuration Procedures for USSD
- 25 5.4 GSM Audio Coding
- 25 5.4.1 Introduction to GSM Audio Coding
- 26 5.4.2 Configuration Procedures for GSM Audio Coding
- 27 5.5 Abnormal Call Handle
- 27 5.5.1 Configuration Procedures for Abnormal Call Handle
- 29 5.6 Enable Call Duration Limitation of Single Call & Enable Call Duration Limitation
- 29 5.6.1 Configuration Procedures for Enable Call Duration Limitation of Single Call
- 30 5.6.2 Configuration Procedures for Enable Call Duration Limitation
- 32 5.7 CLIR & Detect Reverse Polarity
- 32 5.7.1 Configuration procedures for CLIR & Detect Reverse Polarity
- 32 5.8 BCCH
- 33 5.8.1 Configuration Procedures for BCCH
- 34 5.9 Carrier
- 35 5.10 Call Forwarding
- 35 5.11 Call Waiting
- 36 6 Call Control
- 36 6.1 Navigation Subtree of Call Control
- 36 6.2 IP Tel Calls and Tel IP Calls
- 36 6.3 Configuration of IP Trunk and IP Trunk Group
- 36 6.3.1 Configuration of IP Trunk
- 37 6.3.2 Configuration of IP Trunk Group
- 38 6.4 Routing Configuration
- 39 6.5 Operation
- 39 6.5.1 Configuration Procedures for IP -> Tel Operation
- 41 6.5.2 Configuration Procedures for Tel -> IP Operation
- 42 6.6 Number Manipulation
- 42 6.6.1 Configuration Procedures for Manipulating IP –> Tel Destination Numbers
- 44 7 Statistics
- 44 7.1 Navigation Subtree for Statistics
- 44 7.2 TCP/UDP
- 44 7.3 RTP
- 45 7.4 SIP Call History
- 45 7.5 IP to GSM Call History
- 45 7.6 CDR Report
- 46 7.7 Lock BCCH Report
- 46 7.8 Current Call Status
- 47 8 Tools
- 47 8.1 Navigation Subtree of Tools
- 47 8.2 Firmware Upload
- 47 8.3 Provision
- 48 8.3.1 Configuration on FTP Server
- 49 8.3.2 Configuration on DWG2000-1G
- 50 8.4 Filelog Download
- 50 8.5 Management Parameter
- 51 8.6 Config Backup & Config Restore
- 51 8.6.1 Config Backup
- 51 8.6.2 Config Restore
- 51 8.7 IVR Voice Prompt Upload
- 51 8.8 Network Diagnosis
- 51 8.8.1 Ping Test
- 52 8.8.2 Tracert Test
- 52 8.8.3 Network Capture
- 52 8.9 Username & Password
- 53 8.10 Factory Reset
- 53 8.11 Auto Restart and Manually Restart
- 54 9 How to Connect with SIP Server
- 54 9.1 Configuration for connecting DWG2000-1G with Elastix through IP Trunking
- 54 9.1.1 Configuration procedures on Elastix Sever
- 56 9.1.2 Configuration procedures on DWG2000-1G
- 59 Trunking
- 59 9.2.1 Configuration on Elastix Sever
- 62 9.2.2 Configuration Procedures on DWG2000-1G