advertisement
User Manual
– Rev M
California Instruments
1 Introduction
This instruction manual contains information on the installation, operation, calibration and maintenance of all power systems that use the MX15 Series power sources with the programmable controller.
1.1 General Description
The MX15 Series AC and DC power source systems are high efficiency, floor standing AC and
DC power sources that provide a precise output with low distortion. Available voltage ranges are
150 Vac, 300 Vac and 400 Vac in AC mode and 200 Vdc and 400 Vdc in DC mode.
Models with a -1 designation provide full front panel operation but do not include certain features such as arbitrary waveform generation unless added as an option at the time of order. Models with the Pi controller offer several additional standard features, including the RS232C, USB, LAN
(option) and IEEE-488 interfaces, arbitrary waveform generation, dual voltage ranges and additional measurement functions.
The MX15 Series units are contained in a compact floor standing enclosure on casters. This allows the units to be moved around more easily.
Read the installation instructions carefully before attempting to install and operate the MX15
Series power systems.
1.2 Manual organization and format
All user documentation for AMETEK programmable power sources is provided on CDROM in electronic format. (Adobe Portable Document Format) The required Adobe PDF viewer can be downloaded free of charge from www.adobe.com
. This manual may be printed for personal use if a hardcopy is desired. To request a hardcopy from AMETEK Programmable Power, contact customer service at [email protected]
. There will be an additional charge for printed manuals.
This manual contains sections on installation, normal use, maintenance and calibration. If the MX system is equipped with a GPIB, RS232C, USB or LAN interface, refer to the MX Programming manual for information on using the remote control interfaces and command syntax. The programming manual is provided on the same CDROM as this user manual.
MX15 10
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 10 Introduction
- 10 General Description
- 10 Manual organization and format
- 11 Specifications
- 11 Electrical
- 19 Mechanical
- 20 Environmental
- 20 Regulatory
- 20 Front Panel Controls
- 21 Special Features and Options
- 29 Supplemental Specifications
- 34 Unpacking and Installation
- 34 Unpacking
- 34 Power Requirements
- 35 Mechanical Installation
- 35 AC Input Connections and Wiring
- 39 AC On/Off Circuit Breaker on MX Series front panel
- 41 Output Connections
- 49 Connectors - Rear Panel
- 57 Multiple Cabinet Power Up/Down Procedures
- 58 Clock and Lock Configurations
- 61 Basic Initial Functional Test
- 63 Remote Inhibit / Remote Shutdown
- 64 Junction Box Accessory
- 65 Output Filter Box Accessory
- 66 Front Panel Operation
- 66 Tour of the Front Panel
- 71 Menu Structure
- 96 Output Programming
- 98 Waveform Management [1Pi Controller only]
- 102 Standard Measurements
- 104 Advanced Measurements [1Pi Controller only]
- 105 Transient Programming
- 111 Principle of Operation
- 111 General
- 111 Overall Description
- 113 Controller Assembly
- 116 System Interface Board
- 116 Current / Voltage Sensor Board
- 116 Low Voltage Power Supply
- 117 Power Module
- 122 Calibration
- 122 Recommended Calibration Equipment
- 123 Front Panel Calibration Screens
- 124 Routine Measurement Calibration
- 126 Routine Output Calibration
- 127 Non-Routine Calibration
- 130 Service
- 130 Cleaning
- 130 General
- 130 Basic operation
- 132 Advanced Troubleshooting
- 134 Factory Assistance
- 135 Fuses
- 135 Firmware Updates
- 138 Top Assembly Replaceable Parts
- 141 Options
- 141 Introduction
- 141 Option -HV: Additional AC Voltage Range
- 142 –160: RTCA/DO-160 Tests
- 156 –704: MilStd704 Tests
- 169 –ABD: Airbus ABD0100.1.8 Test
- 169 –787: Boeing B787-0147 Test
- 170 –WHM: Watt Hour Measurement
- 171 –411: IEC 61000-4-11 Voltage Dips and Interruptions
- 172 –413: IEC 61000-4-13 Interharmonics Test
- 174 –SNK: Current Sink
- 177 . Error Messages
- 182 Index