advertisement
User Manual
– Rev M
California Instruments
2.1.7 Unit Protection
Input Over current:
Input Over voltage:
Input Over voltage
Transients:
Output Over current:
Output Short Circuit:
Over temperature:
2.2 Mechanical
Parameter
Dimensions:
(for each MX chassis)
In-line fast acting fuses. Check fuse rating in Service and Maintenance section. Ratings will depend on AC input configuration settings.
Circuit breaker for LV supply.
Automatic shutdown.
Surge protection to withstand EN50082-1 (IEC 801-4, 5) levels.
Adjustable level constant current mode with programmable set point.
Peak and RMS current limit.
Automatic shutdown.
Unit Weight:
(for each MX chassis)
Material:
Finish:
Cooling:
Internal Construction:
Rear Panel
Connections:
Specification
Height:
Width:
Depth:
Net:
Shipping:
31.75”
24”
28”
806 mm
610 mm
711 mm
600 lbs / 272 Kg approximately
681 lbs / 309 Kg approximately
Steel chassis with aluminum panels and covers.
Light textured painted external surfaces.
Panels semi-gloss polyurethane color no. 26440 (medium gray)
Fan cooled with air intake on the front and exhaust to the rear.
Fans: 2 x 225CFM.
Air displacement 7.5 Cu Ft/sec. Max.
Modular sub assemblies.
(See section 3 for description of connections)
Cable entry and strain relieve for AC input wiring
Cable entry and strain relieve for output wiring
External sense terminal block (Remote voltage sense)
System interface (2x)
Clock and Lock BNC's (requires -LKM or -LKS options)
RS232, USB, GPIB, LAN (option)
Trigger In BNC
Trigger Out BNC
Function Strobe BNC
Output Status
MX15 19
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 10 Introduction
- 10 General Description
- 10 Manual organization and format
- 11 Specifications
- 11 Electrical
- 19 Mechanical
- 20 Environmental
- 20 Regulatory
- 20 Front Panel Controls
- 21 Special Features and Options
- 29 Supplemental Specifications
- 34 Unpacking and Installation
- 34 Unpacking
- 34 Power Requirements
- 35 Mechanical Installation
- 35 AC Input Connections and Wiring
- 39 AC On/Off Circuit Breaker on MX Series front panel
- 41 Output Connections
- 49 Connectors - Rear Panel
- 57 Multiple Cabinet Power Up/Down Procedures
- 58 Clock and Lock Configurations
- 61 Basic Initial Functional Test
- 63 Remote Inhibit / Remote Shutdown
- 64 Junction Box Accessory
- 65 Output Filter Box Accessory
- 66 Front Panel Operation
- 66 Tour of the Front Panel
- 71 Menu Structure
- 96 Output Programming
- 98 Waveform Management [1Pi Controller only]
- 102 Standard Measurements
- 104 Advanced Measurements [1Pi Controller only]
- 105 Transient Programming
- 111 Principle of Operation
- 111 General
- 111 Overall Description
- 113 Controller Assembly
- 116 System Interface Board
- 116 Current / Voltage Sensor Board
- 116 Low Voltage Power Supply
- 117 Power Module
- 122 Calibration
- 122 Recommended Calibration Equipment
- 123 Front Panel Calibration Screens
- 124 Routine Measurement Calibration
- 126 Routine Output Calibration
- 127 Non-Routine Calibration
- 130 Service
- 130 Cleaning
- 130 General
- 130 Basic operation
- 132 Advanced Troubleshooting
- 134 Factory Assistance
- 135 Fuses
- 135 Firmware Updates
- 138 Top Assembly Replaceable Parts
- 141 Options
- 141 Introduction
- 141 Option -HV: Additional AC Voltage Range
- 142 –160: RTCA/DO-160 Tests
- 156 –704: MilStd704 Tests
- 169 –ABD: Airbus ABD0100.1.8 Test
- 169 –787: Boeing B787-0147 Test
- 170 –WHM: Watt Hour Measurement
- 171 –411: IEC 61000-4-11 Voltage Dips and Interruptions
- 172 –413: IEC 61000-4-13 Interharmonics Test
- 174 –SNK: Current Sink
- 177 . Error Messages
- 182 Index