- No category
advertisement
Revision History
A manual revision code appears as a suffix to the catalog number on the cover of the manual.
Man.No. V085-E1-[]
Revision code
The following table outlines the changes made to the manual during each revision. Page numbers refer to the previous version.
Revision code
01
02
03
04
05
06
07
Date Revised content
October 2003 Original production
July 2004 Addition of information related to NS-Designer Ver.6.0 upgrade
February 2005 Addition of information related to NS-Designer Ver.6.2 upgrade
July 2006
July 2007
Addition of information related to CX-Designer release
Addition of information related to CJ1H-CPU[][]H-R release
June 2008 Addition of information related to NS5-[][]1[][] release
October 2010 Addition of information related to CX-Designer release
OMRON Corporation
Industrial Automation Company
Tokyo, JAPAN
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69-2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,
IL 60173-5302 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
Authorized Distributor:
© OMRON Corporation 2009 All Rights Reserved.
In the interest of product improvement, specifications are subject to change without notice.
Cat. No. V085-E1-07
1010
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Notice
- 3 Contents
- 4 About this Manual
- 5 Related Manuals
- 6 Terminology
- 7 Introduction
- 10 Section 1
- 11 1-1 List of combinations
- 11 1-1-1 Connection of temperature controller
- 11 1-1-2 Connection with memory link
- 12 1-2 CX-Designer and System Program versions
- 12 1-2-1 CX-Designer versions
- 12 1-2-2 System Program versions
- 13 Section 2
- 14 2-1 Outline
- 15 2-2 Possible combinations
- 15 2-2-1 Connectable temperature controller
- 15 2-2-2 Temperature controller Manuals
- 16 2-3 Configurations
- 16 2-3-1 Necessary parts
- 17 2-3-2 Wiring diagram
- 18 2-3-3 Temperature controller communications settings
- 19 2-3-4 CJ1W-CIF11 setting
- 19 2-3-5 NS setting
- 20 2-4 Setting Project
- 21 2-5 Monitor variables area in temperature controller
- 21 2-5-1 Variables area in temperature controller
- 23 2-5-2 Address notation in CX-Designer
- 23 2-5-3 Use of double word numbers
- 23 2-5-4 Communications writing enabled/disabled
- 24 2-6 Operation of Temperature Controller
- 24 2-6-1 How to create a Smart Active Parts part
- 27 2-6-2 Smart Active Parts Operations
- 30 2-7 Restrictions
- 30 2-7-1 The behavior of 2 word number in the CX-Designer test function
- 30 2-7-2 Address display when address error occurs
- 31 2-7-3 Communications address set when functional part was copiedusing repeat command
- 32 Section 3
- 33 3-1 How does Memory Link work
- 33 3-1-1 PT memory
- 33 3-1-2 Command and response
- 35 3-1-3 Action when command is used
- 36 3-1-4 Notify Command Behavior
- 36 3-1-5 Flow control
- 37 3-2 Settings
- 37 3-2-1 Making settings for the Project
- 39 3-2-2 Communications conditions setting
- 39 3-2-3 NS system menu operation
- 40 3-2-4 Connection Diagram
- 41 3-3 Communications procedures
- 41 3-3-1 Memory Link Commands
- 60 3-4 What has been changed since NT31/631
- 60 3-4-1 Memory Link Commands
- 63 Revision History