- No category
advertisement
Once the PCS250G’s tamper switch is closed, the panel will reset the trouble message and a tamper restore message will be sent to the monitoring station and to the SMS recipients. Also, upon the closure of the PCS250G’s tamper switch there is a 30s delay before the PCS250G sends out a “tamper close” status to the panel.
The PCS250G GPRS Communicator Module’s tamper functionality is supported with a compatible Paradox control panel.
• MG/SP v4.90 and higher
• EVO192 v2.71 or higher
• EVOHD v1.0 or higher
• SP4000/SP65 v5.10 or higher
• IP150 v1.2 or higher
• UC300 v1.0 or higher
Specifications
The following table describes the technical specifications of the
PCS250G GPRS Communicator Module.
Power
Antenna
Power Input
Consumption
Class 4 (2W) @ 850/900 MHz
Class 2 (1W) @ 1800/1900 MHz
Gain <3dBi; impedance 50 Ohm
Input power >2W peak power
12 VDC nominal
100 mA standby, average 450 mA
(1.2 A peak) during GPRS transmission
0ºC to 50ºC (32ºF to 122ºF) Operating
Temperature
Encryption
SMS Protocol
Humidity
Weight
Dimensions
Certification
128-bit (MD5 and RC4) or 256-bit (AES)
8-bit (ISO/IEC 8859-1) or 16-bit (UCS2
ISO/IEC10646)
5-90%
200 g (7.05 oz)
17.2 x 9.8 x 4.4 cm (6.8 x 3.9 x 1.7 in.)
EN 50136 ATS 5 Class II
Overview Page 9
advertisement
Related manuals
advertisement
Table of contents
- 4 Features
- 5 In the Box
- 5 Required/Optional Items
- 5 Compatibility
- 6 System Components
- 7 LED Feedback
- 7 Communication Loss
- 8 SIM Card Functionality
- 8 Tamper Switch Functionality
- 9 Specifications
- 10 SIM Card Connection
- 11 GPRS Connections
- 12 Communication Bridge
- 13 UC300 Connection
- 14 Optional Power Supply Connections
- 14 Using an External Power Input
- 15 Antenna Extension Installation (Optional)
- 15 Module Installation
- 17 Frequency Band
- 17 Bandwidth Saver Mode
- 17 SMS Forwarding
- 17 Communicating Using Text Messages
- 18 Programming Phone Numbers At The Panel
- 18 Forwarding SMS Text Messages
- 18 Receiving Text Messages
- 18 Configuring GSM Network Provider Information
- 20 Configuring BabyWare Access
- 20 Programming and Registering GPRS Reporting Options
- 22 SMS Backup Reporting
- 22 Configuring the PCS250G for SMS Backup Reporting
- 24 Troubles
- 24 Text Message Notification
- 25 SMS Language
- 26 Arm/Disarm System via Text Message
- 27 List of SMS Commands
- 29 Public Network
- 30 Private Network
- 32 End User SMS Programming
- 32 End User SMS Programming with Digiplex EVO
- 32 End User SMS Programming with MG/SP / E-Series
- 33 View GPRS IP Information
- 34 Viewing GPRS IP Information with Digiplex EVO
- 34 Viewing GPRS IP Information with MG/SP / E-Series
- 35 Alarm Messages
- 36 Arming/Disarming Messages
- 37 Trouble Event Messages
- 38 Trouble Restore Messages
- 38 UC300 Messages
- 39 UC300 Alarm Messages
- 40 UC300 Arming/Disarming Messages
- 40 UC300 Trouble Messages
- 43 UC300 Trouble Restore Messages