Chapter 3 – Using the Web Management Software
Caller ID Configuration Group
Add “Wakeup on Call” Caller ID:
To add Caller ID to the Wakeup-on-Call function, enter the Caller ID that can wake up the router. Enter ‘RING’ (all Caps) to wake up on any call.
Enter a CID phone number or an SMS message.
Ensure the SMS message string does not contain any spaces between words.
After entering the Caller ID, click the Add button. The Caller ID displays at the bottom of the page. You can enter any number of IDs.
A Caller ID can be edited or deleted using Options, which are available once a Caller ID is displayed.
Caller Acknowledgement Configuration
Acknowledgement String to Caller:
The configured string of (0 to 40 characters) that is sent to the integrated cellular modem upon receiving a valid caller ID from the WAN. The default is NULL string.
Note:
If the string is not configured, acknowledgement to the caller is not sent upon successful caller ID reception.
Submitting and Saving Your Changes
To save these settings, click Submit.
To ensure your changes go into effect, click Save and Restart.
Wakeup-On-Call Examples
Example 1 – Set Up the Ethernet Router to Activate on Incoming SMS Message
1.
On the
PPP > PPP Configuration
page, configure the following parameters:
●
PPP General
Make sure that PPP is Enabled (the default).
●
Make sure Dial-on-Demand is Enabled (the default).
Set the Idle Time Out to the number of seconds you desire.
Authentication
Your wireless service provider may require you to have a separate PPP Username and Password. If so, enter them here.
Note: If a username and password are required, your wireless provider likely gave these items to you when you activated your account.
●
Modem Configuration
Make sure your Dial Number is entered correctly.
For GSM models, the Dial Number is *99***1#
For CDMA models, the Dial Number is
#777
Enter your APN. Your wireless service provider assigns the APN.
Example: AT+CGDCONT=1,"IP","Internet" The Example: AT+CGDCONT=1,”IP”,”Internet” needs to be removed. Just the APN name needs to be entered in the APN field.
2.
To save the changes made on this page, click Submit.
54 MultiModem rCell User Guide
Chapter 3 – Using the Web Management Software
3.
On the
PPP > Wakeup-on-Call
screen, configure the following parameters:
●
Wakeup-on-Call Configuration
Select Enable for Wakeup-on-Call.
●
Set the Time Delay. You can use the 10 second default.
Enter the Init Strings from the model dependent table described in the Wakeup-on-Call Configuration.
4.
To save the changes made on this page, click Submit.
●
Caller ID Configuration
Enter an SMS to add to the Caller ID list.
Note:
Add the SMS message string into the Caller ID list. The SMS message string must not contain any spaces between words. When the configured string matches the SMS message string, it activates the
Wakeup-on-Call feature.
●
To save each message as it is entered into the Caller ID list click Add.
Caller Acknowledgement Configuration
Enter a configured string (0 to 40 characters) that is sent to the integrated cellular modem upon receiving a valid Caller ID from the WAN.
Set the Wakeup Acknowledgement string configuration with the command at+cnma
To save the Acknowledgement Configuration, click the Submit.
5.
To ensure your changes go into effect, click Save and Restart. The device saves all the settings and reboots the computer.
MultiModem rCell User Guide 55
Chapter 3 – Using the Web Management Software
Example 2 – Determine if the router Is Supporting Incoming Calls and Caller ID
1.
On the PPP > PPP Configuration page, make sure that PPP is Disabled.
2.
On the PPP > Wakeup-on-Call screen, make sure that Wakeup-on-Call is Disabled.
3.
To open a command prompt, from the Start button and select Run.
4.
Type CMD to open the command window. Click OK.
5.
When the command window opens, telnet to the router
.
Note:
5000 is the router port number. d. Enter your username and password to login. e. Enter an AT command to make sure you receive a response; i.e., OK. f. To determine the dial number of your router, enter the command AT+CNUM.
6.
For the Wakeup-on-Call function to work the RING or CALLER ID information must appear.
To determine if the RING message shows, from another phone, call your router using the dial number of your router.
7.
To enable Caller ID, enter the AT+CLIP=1 command. Make the call again to verify Caller ID information.
Some wireless providers do not provide caller ID information if you have only a data plan.
Example 3 – Set Up the Ethernet Router to Activate on ALL Incoming Calls
1.
On the
PPP >PPP Configuration
page, set up the following parameters:
PPP General
●
Make sure that PPP is Enabled.
●
Make sure Dial-on-Demand is Enabled.
●
Set the Idle Time Out to the number of seconds you desire.
Authentication
●
Your wireless service provider may require you to have a separate PPP User name and Password. If so, enter them here.
Note:
If a username and password are required, your wireless provider likely gave you these items when you activated your account.
Modem Configuration
●
●
Make sure your Dial Number is entered correctly:
For GSM models, the Dial Number is *99***1#
●
Submit
For CDMA models, the Dial Number is #777
●
Click the Submit button to save the changes made on this screen.
56 MultiModem rCell User Guide
Chapter 3 – Using the Web Management Software
2.
On the
PPP > Wakeup-on-Call
screen, set up the following parameters:
Wakeup-on-Call Configuration
●
Select Enable for Wakeup-on-Call.
●
●
Set the Time Delay to 3 seconds. You can use the 10 second default.
Ensure all Init Strings are empty.
●
●
Submit Button
Click the Submit button to save these settings.
Caller ID Configuration
●
Enter the string RING to the Caller ID list.
3.
●
Click the Add Button to save the string to the Caller ID list.
To ensure your changes go into effect, click Save and Restart. The device saves all the settings and reboots the computer.
Example 4 – Set Up the Ethernet Router to Activate on Matching Caller IDs Only:
1.
On the
PPP > PPP Configuration
screen, set up the following parameters:
PPP General
●
Make sure that PPP is Enabled.
●
●
Make sure Dial-on-Demand is Enabled.
Set the Idle Time Out to the number of seconds you desire.
Authentication
●
Your wireless service provider may require you to have a separate PPP username and password. If so, enter them here.
Note:
If a username and password are required, your wireless provider likely gave you these items when you activated your account.
Modem Configuration
●
Make sure your Dial Number is entered correctly:
For GSM models, the Dial Number is *99***1#
For CDMA models, the Dial Number is #777
MultiModem rCell User Guide 57
