Product description. White-Westinghouse WASC24C6CHLW, WASC24P5ATLW, WASE12P5ATLW, WAS(C,E)18C6CHLW, E)24C6CHLW, WASE09C5ATLW, WASE09P6CHLW, WASC09C5ATLW, WASE24C6CHLW, WASE24P5ATLW

Product description

3

4

5

6

7

8

1

2

9

Front panel

Air filter

(inside front panel)

Horizontal airflow grille

Vertical airflow grille

Temperature sensor

(inside front panel)

Panel

Infra-red signal receiver

Drain hose connector and refrigerant gas connector

Remote control

10

11

12

Connector cable

Detection valve

Drain hose and refrigerant connecting pipe

4

3

Air outlet

5

8

7

Air inlet

6

1

Air inlet

9

12

Attention

All the pictures in this manual are for explanation purpose only. They may be slightly different from the air conditioner you purchased.

Air outlet

31

Product description

Outdoor unit

10

8

11

Display panel

(indoor unit)

13

OPERATION

This lamp illuminates when the air conditioner is in operation.

14

TIMER

Lights up during Timer operation.

15

DEFROST indication lamp

(Enabled on cooling & heating models only): Lights up when the air conditioner starts defrosting automatically or when the warm air control feature is activated in heating operation.

16

Temperature indicator

Displays the temperature settings when the air conditioner is operational. Displays the malfunction code.

17

Signal receiver

13

15 14

17

16

13

15

14 17 16

Attention

The description in the control is based on a typical model. The functions are the same in your air conditioner, even if there are some differences in the appearance.

Product description

32

Remote control

Remote control operation

1. Operation mode: Cold, Heat (Only for the models with cold/heat), DRY,

FAN, and AUTO (Automatic).

2. Timer 24 hrs.

3. Internal temperature range selection:

17º - 30º.

4. LCD

5. Night light operation mode.

ESPECIFICACIONES DEL CONTROL REMOTO

Rated voltage

Lowest of voltage of CPU emiting signal

Transmission distance

Environment

* With 3 V, reaches 11m

3 V

2,4 V

8 m*

-5ºC ~ 60ºC

Attention

1. The air conditioner will not operate when curtains, doors our other materials block the signals between the remote control and the indoor unit.

2. Avoid spilling any liquid in the remote control. Do not expose to sunlight or any heat source.

3. If the infrared signal receiver in the indoor unit is exposed to sunlight, the air conditioner unit might not work properly. Use curtains or shades to avoid having sunlight directly to the receiver.

4. If other electrical equipment react to the signals sent by the remote control, change the position or consult with you local sales department.

Remote control battery

To use the remote control, it is necessary to install two (R03/Ir03x2) alkaline AAA batteries.

33

Remote control

When should the batteries be replaced

1. When there is not a “beep” anymore from the indoor unit when using the control remote or the signal light indicator does not lit.

2. The indoor unit does not respond to the remote control commands to activate the programs.

To replace batteries

1. Slide out the battery compartment cover ( located in the back part of the remote control).

2. Install the two AAA batteries in the compartment (indicated in the drawing located inside the compartment).

3. Slide in the cover.

4. If the remote control is not operated for long period of times, batteries should be discarded.

Remote control instructions

1. The signal reach distance of the remote control to the receiver that is inside the main unit of the air conditioner is 8 meters. Any obstruction placed between the receiver and the remote control can cause interference, limiting the capacity of the programming.

2. Any time that a button is pressed in the remote control, the air conditioner emits a “beep” that indicates that a command has been received and transmitted in the indoor unit.

3. When selecting the function of timer, the remote control sends

(automatically) a signal to the indoor unit at the specific moment. If the control remote is left in a position that the signal is blocked, a 15 minute delay can be produced.

Attention

1. When replacing batteries, do not use old batteries or a different type battery. This may cause the remote control to malfunction.

2. If you do not use the remote controller for several weeks remove the batteries. Otherwise battery leakage may damage the remote controller.

3. The average battery life under normal use is about 6 months.

4. Replace the batteries when there is no answering beep from the indoor unit or if the Transmission

Indicator light fails to light.

Remote control

34