Remote control description. White-Westinghouse WASC24C6CHLW, WASC24P5ATLW, WASE12P5ATLW, WAS(C,E)18C6CHLW, E)24C6CHLW, WASE09C5ATLW, WASE09P6CHLW, WASC09C5ATLW, WASE24C6CHLW, WASE24P5ATLW

DRY operation

The dry mode will automatically select the drying operation based on the difference between the set temperature and the actual room temperature.

The temperature is regulated while dehumidifying by repeating turning on and off of the cooling operation or fan only. The fan speed is LOW.

1. Push the MODE button to select

DRY.

2. Push the TEMP button to set the desired temperature from 21ºC to

28ºC.

3. Push the ON/OFF button, the operation lamp lights and the air conditioner start to operate in the

DRY mode. FAN SPEED is Low.

Push the ON/OFF button again to stop this unit operation.

Attention

Due to the difference of the set temperature of the unit and the actual indoor temperature, the Air Conditioner when in DRY mode will automatically operate many times without running the

COLD and FAN mode.

Room

Temperature

Cooling

Fan only

Cooling

Set temperature

Fan only

Time

Cooling

DRY FUNCTION

Air flow direction adjustment

Use SWING to adjust the airflow direction up and down.

1. When swing is pressed the horizontal louver moves up and down automatically. Press again to stop operation.

Attention

If the louver oscillates or moves in a position that could affect the cooling or heating of the air conditioner the direction of the oscillation/movement would alter automatically.

39

How the air conditioner works

SLEEP mode

Press the sleep button to activate the sleep mode. To deactivate, press the button again.

Cold only mode:

• The indoor unit fan operates at a low velocity.

• After and hour of operation, the adjusted temperature will increase

1º C. After, the unit keeps operating

2ºC above the adjusted temperature.

In heating mode (some models):

• The indoor unit fan operates at a low velocity.

• After and hour of operation, the adjusted temperature will decrease

1º C. After, the unit keeps operating

2º C below the adjusted temperature.

Attention

Sleep function is only availaible in the Cold/Heat and AUTO mode.

1 °C

1 hour 1 hour

SLEEP FUNCTION (Cooling mode)

1 °C

1 °C

1 °C

1 hour 1 hour

7 hours

SLEEP FUNCTION (Heating mode)

TIMER Operation

TIMER button can set the auto-on time of the unit.

To set the starting time

1. Push the TIMER ON button, then the remote controller shows TIMER ON , the last set time for the starting operation and the signal "h" will be shown on the DIGITAL DISPLAY area. You are now ready to reset the time to START the operation.

2. Push the TIMER ON button again to set desired unit start time.

3. After setting the TIMER ON ,there will be a one-half second delay before the remote controller transmits the signal to the air conditioner. Then, after approximately another 2 seconds, the signal "h" disappears and the set temperature will re-appear on the digital display.

How the air conditioner works

40

To set the stopping time

1. Push the TIMER OFF button and the remote controller will show TIMER

OFF, the last set time for the stopping operation and the signal "h" will be shown on the DIGITAL DISPLAY area. You are now ready to reset the time of the STOP operation.

2. Push the TIMER OFF button again to set the time you want to stop the operation.

3. After setting the TIMER OFF ,there will be a one-half second delay before the remote controller transmits the signal to the air conditioner. Then, after approximately another 2 seconds, the signal "h" disappears and the set temperature will re-appear on the digital display.

Exemples:

ON

OFF

6h

(Temp On)

ON

OFF

6h

(Temp Off)

ON ON

OFF

12h

(Temp Off)

14h

(Temp On)

ONN

OFF OFF

20h

(Temp On)

23h

(Temp Off)

Optimal operation

To achieve optimal performance, please note the following:

1. Adjust the air flow direction correctly so that it is not directed on people.

2. Adjust the temperature to achieve the highest comfort level. Do not adjust the unit to excessive temperature levels.

3. Close doors and windows on COLD or HEAT modes, or performance may be reduced.

4. Use TIMER ON button on the remote controller to select a time you want to start your air conditioner.

5. Do not put any object near air inlet or air outlet, as the efficiency of the air conditioner may be reduced and the air conditioner may stop running.

6. Clean the air filter periodically, otherwise cooling or heating performance may be reduced.

7. Do not operate unit with horizontal louvre in closed position.

41

How the air conditioner works

How to use the indoor unit

Adjusting air flow direction

Adjust the air flow direction properly otherwise, it might cause discomfort or cause uneven room temperatures.

Adjust the horizontal louver using the remote controller. Adjust the vertical louver manually.

Adjusting the vertical air flow direction (up - down)

The air conditioner automatically adjusts the vertical air flow direction in accordance with the operating mode.

To set the horizontal air flow direction (left/ right)

Adjust the vertical louver manually using the lever on the left or right side of the vertical louver arm (Depending on model). Take care not to catch fingers on the fan, horizontal louver or to damage vertical louvers. When the air conditioner is in operation and the horizontal louver is in a specific position, move the lever at left (or right, depending on model) end of the air outlet to the desired position.

To automatically swing the air flow direction (up/down)

Perform this function while the air conditioner is in operation.

Press the SWING button on the remote controller.

To stop the function, press the SWING button again.

Lever

How to use the indoor unit

42