advertisement
Manual VIPA System 200V
Chapter 1 Basics and Assembly
Installation
General
Profile rail
The modules are each installed on a 35mm profile rail and connected via a bus connector. Before installing the module the bus connector is to be placed on the profile rail before.
For installation the following 35mm profile rails may be used:
35 mm
35 mm
Bus connector
27 mm
Order number
290-1AF00
290-1AF30
Label
27 mm
35mm profile rail
35mm profile rail
Description
Length 2000mm, height 15mm
Length 530mm, height 15mm
System 200V modules communicate via a backplane bus connector. The backplane bus connector is isolated and available from VIPA in of 1-, 2-, 4- or 8tier width.
The following figure shows a 1tier connector and a 4tier connector bus:
The bus connector is to be placed on the profile rail until it clips in its place and the bus connections look out from the profile rail.
Order number Label Description
HB97E - IM - RE_253-1NE00 - Rev. 12/44 1-7
Chapter 1 Basics and Assembly
Manual VIPA System 200V
Installation on a profile rail
1 2
The following figure shows the installation of a 4tier width bus connector in a profile rail and the slots for the modules.
The different slots are defined by guide rails.
3 [1] Head module
(double width)
[2] Head module
(single width)
4
PW
ER
RD
BA
ADR.
0 1
+
-
DC24V
1
2
R
S
PW
SF
FC
MC
MMC
Assembly regarding the current consumption
•
Use bus connectors as long as possible.
•
Sort the modules with a high current consumption right beside the head module. In the service area of www.vipa.com a list of current consumption of every System 200V module can be found.
1-8 HB97E - IM - RE_253-1NE00 - Rev. 12/44
Manual VIPA System 200V
Chapter 1 Basics and Assembly
Assembly possibilities
hoizontal assembly
0 1 lying assembly vertical assembly
Please regard the allowed environmental temperatures:
• horizontal assembly:
• vertical assembly:
• lying assembly: from 0 to 60°C from 0 to 40°C from 0 to 40°C
The horizontal assembly always starts at the left side with a head module, then you install the peripheral modules beside to the right.
You may install up to 32 peripheral modules.
Please follow these rules during the assembly!
•
Turn off the power supply before you install or remove any modules!
•
Make sure that a clearance of at least 60mm exists above and 80mm below the middle of the profile rail.
1
4
2 3
•
Every row must be completed from left to right and it has to start with a head module.
[1] Head module (double width)
[2] Head module (single width)
•
Modules are to be installed side by side. Gaps are not permitted between the modules since this would interrupt the backplane bus.
•
A module is only installed properly and connected electrically when it has clicked into place with an audible click.
•
Slots after the last module may remain unoccupied.
Note!
Information about the max. number of pluggable modules and the max. current at the backplane bus can be found in the "Technical Data" of the according head module.
Please install modules with a high current consumption directly beside the head module.
HB97E - IM - RE_253-1NE00 - Rev. 12/44 1-9
Chapter 1 Basics and Assembly
Assembly procedure
Manual VIPA System 200V
•
Install the profile rail. Make sure that a clearance of at least 60mm exists above and 80mm below the middle of the profile rail.
•
Press the bus connector into the profile rail until it clips securely into place and the bus-connectors look out from the profile rail. This provides the basis for the installation of your modules.
•
Start at the outer left location with the installation of your head module and install the peripheral modules to the right of this.
1 2 3
[1] Head module
(double width)
(single width)
4
•
Insert the module that you are installing into the profile rail at an angle of 45 degrees from the top and rotate the module into place until it clicks into the profile rail with an audible click. The proper connection to the backplane bus can only be guaranteed when the module has properly clicked into place.
Attention!
Power must be turned off before modules are installed or removed!
1-10
Clack
HB97E - IM - RE_253-1NE00 - Rev. 12/44
advertisement
Related manuals
advertisement