advertisement
MAINTENANCE SCHEDULE
Service Performed
Check Clutch Lever
Operation
Check Dual Handle
Interlock
Check Fasteners
Clean Recoil Guard Foam
Cover
•
•
•
•
Check Engine Oil
Check Clutch Cable
Adjustments *
Check Tire Pressure
Change Engine Oil **
•
•
•
General Lubrication • •
* After first use.
** Refer to engine manual for instructions.
SERVICE PARTS
See your Ariens dealer to purchase service parts for your unit.
Part No.
Description
Ariens Hi-Temp Grease
• 3 oz. cartridges (3)
• 14 oz. cartridge (1)
Fuel Stabilizer (4 oz.)
Spark Plug
Ariens 5W-30 Engine Oil
• 16 oz.
• 32 oz.
00036800
00036700
04730400
04742500 (for
Canada Only)
21530400
00091000
00067600
CHECK DUAL HANDLE
INTERLOCK
1. Stop engine.
2. Engage traction drive clutch and then the attachment drive clutch.
3. Release the attachment clutch lever. The attachment clutch should stay engaged until the traction drive clutch lever is released.
CHECK FASTENERS
Check for loose hardware.
CHECK CLUTCH CABLE
ADJUSTMENTS
Brush must stop within 5 seconds when attachment clutch lever is released.
Wheels must stop quickly when traction drive clutch lever is released.
If clutches do not engage or disengage
correctly, see Adjust Attachment Clutch &
Brake on page 21 or See Adjust Traction
CHECK TIRE PRESSURE
Keep tires inflated to pressure listed on tire sidewall.
WARNING: AVOID INJURY.
Explosive separation of tire and rim parts is possible.
• DO NOT inflate tires above the recommended pressure.
• DO NOT inflate tires with a compressor; use a hand pump.
• DO NOT stand in front of tire assembly when inflating. Use a clip-on chuck and extension hose long enough to allow you to stand to one side.
• DO NOT mount a tire without proper equipment and experience.
CHECK ENGINE OIL
NOTICE: Engine oil level must be maintained at correct level or engine damage may occur.
Refer to engine manual.
CHANGE ENGINE OIL
Refer to engine manual.
CLEAN RECOIL GUARD FOAM
COVER
The recoil guard foam cover must be kept clean and free of snow and debris.
If cover becomes clogged, remove and gently vacuum or wash with warm water.
IMPORTANT: Cover MUST be installed when using unit in winter conditions. The cover prevents snow from entering the recoil guard and freezing the recoil pawls. Cover is not necessary for operation during non-winter months.
IMPORTANT: If cover is clogged with snow, remove it and allow foam to thaw or rinse with warm water. Allow cover to dry before reinstalling.
EN - 18
advertisement
Related manuals
advertisement
Table of contents
- 3 Welcome
- 4 Safety
- 4 Practices & Laws
- 4 Emission Control System
- 4 Required Operator Training
- 4 Safety Alert Symbol
- 4 Signal Words
- 5 Safety Decals
- 6 Safety Rules
- 10 Assembly
- 10 Unpack Unit
- 12 Controls & Features
- 13 Engine Switch
- 13 Fuel Valve
- 13 Electric Start Button
- 13 Choke Control Lever
- 13 Throttle Control Lever
- 13 Speed Selector Lever
- 13 Attachment Clutch Lever (Right Side)
- 14 Traction Drive Clutch Lever (Left Side)
- 14 Brush Lock Trigger
- 14 Dual Handle Interlock
- 14 Operation
- 14 Emergency Stopping
- 14 Before Operating Unit
- 14 Start The Engine
- 15 Operate Unit
- 15 Stop the Engine
- 15 Set Brush Height
- 16 Set Brush Angle
- 16 Transport Unit
- 17 Maintenance
- 17 Service Position
- 19 Return Unit to Operating Position
- 20 Maintenance Schedule
- 20 Service Parts
- 20 Check Dual Handle Interlock
- 20 Check Fasteners
- 20 Check Clutch Cable Adjustments
- 20 Check Tire Pressure
- 20 Check Engine Oil
- 20 Change Engine Oil
- 20 Clean Recoil Guard Foam Cover
- 21 Lubricate Unit
- 22 Adjustments
- 22 Adjust Speed Selector Lever
- 23 Adjust Attachment Clutch & Brake
- 25 Adjust Traction Drive Clutch
- 26 Storage
- 26 Short Term
- 26 Long Term
- 26 Start-of-Season Fuel Preparation
- 26 Accessories
- 27 Troubleshooting
- 29 Specifications
- 30 Warranty