- No category
advertisement
3.
Install drives in the removable media bays on the server.
CAUTION:
Do not use hot-pluggable drives on the same SCSI bus as non-hot-pluggable drives.
TIP: Drives that are to be grouped in the same array should all have comparable capacity for efficient use of total storage capacity.
For additional information about drive installation, see
Appendix B (page 67) . Also consult
the drive documentation.
When you have finished installing drives, go to the next step.
If the drives are hot-pluggable, go to step 4.
If the drives are not hot-pluggable, go to step 5.
4.
Attach the internal point-to-point SCSI cable (provided with the server) from the internal connector of the controller to the hot-plug drive cage.
Installation of the hot-pluggable drives is complete.
5.
For each SCSI bus, manually set the SCSI ID on each drive to a unique value ranging from
0 to 15.
IMPORTANT:
Do not use ID 7, which is reserved for controller use.
For detailed instructions on setting SCSI ID, consult the drive documentation.
6.
Attach a multi device SCSI cable from the internal connector of the controller to the non-hot-pluggable hard drives. This cable may be provided with the server.
7.
Replace the access panel and secure it with the thumbscrews if any are present.
CAUTION:
Do not operate the server with the access panel removed for extended periods of time. The access panel protects thermally sensitive components by ensuring the proper airflow through the server, and also minimizes personal contact with hazardous energy levels.
Verifying the Installation
After the system reboots, verify that the installation was successful by following these steps:
32 Installing Smart Array 6400 Series Controllers
advertisement
Related manuals
advertisement
Table of contents
- 11 Intended Audience
- 11 New and Changed Documentation in This Edition
- 11 Publishing History
- 12 Document Organization
- 12 Typographical Conventions
- 12 HP-UX Release Name and Release Identifier
- 13 Related Documents
- 13 HP Encourages Your Comments
- 15 6402 and 6404 Controller Features
- 16 Board Components and Features
- 17 Controller Board Runtime LEDs
- 18 Cache Module LEDs
- 19 Expansion Module Components
- 19 PCI System Interface
- 19 SCSI Support
- 20 Fault Management Features
- 21 Fault Management in Supported RAID Configurations
- 21 Choosing a RAID Method
- 23 Overview of Installation Steps
- 23 Smart Array 6400 Series Controller Array Configuration Guidelines
- 23 Installation Prerequisites for the Smart Array 6400 Series Controller
- 25 Downloading Software for the Smart Array 6400 Series Controllers
- 25 Installing Software for Smart Array 6400 Series Controllers
- 25 Preparing for the Smart Array 6400 Series Controller Installation
- 26 Installing Smart Array 6400 Series Controller Hardware Offline
- 27 Online Addition and Replacement
- 28 Online Installation of a Smart Array 6400 Series Controller
- 29 Connecting the Cables and the StorageWorks or MSA 30 Disk Enclosures
- 30 External Cabling for HP Servers
- 31 Connecting External Storage
- 31 Labeling the Cables
- 31 Connecting Internal Storage
- 32 Verifying the Installation
- 33 Smart Array 6400 Series Controller Firmware
- 33 Determining the Smart Array 6400 Series Controller Device File
- 34 Determining the Smart Array 6400 Series Controller Firmware Version
- 35 Updating the Smart Array Controller Firmware
- 36 Physical Disk Firmware
- 37 Determining the Smart Array 6400 Series Controller Device File
- 37 Determining the SCSI Channel, ID, and Firmware Version for Physical Disks
- 39 Updating Physical Disk Firmware
- 41 Setting up a Smart Array 6400 Series Controller as a Boot Device
- 41 Planning to Install HP-UX on a Logical Drive
- 41 Configuring for HP-UX 11i v2 or 11i v3 Using ORCA Offline
- 43 Configuring for HP-UX 11i v1 Using Ignite-UX Offline
- 45 Planning the RAID Configuration
- 45 The saconfig Configuration CLI
- 49 Displaying the Smart Array 6400 Series Controller Configuration
- 49 Configuring a Logical Drive
- 51 Deleting a Logical Drive
- 51 Clearing the Logical Drive Configuration
- 51 Adding a Spare Disk
- 51 Deleting a Spare Disk
- 52 Changing the Rebuild Priority of a Logical Drive
- 52 Specifying the Percentage of Cache Used for Read Caching
- 52 Auto-Fail Missing Disks At Boot
- 52 Creating Multiple Logical Drives in an Array
- 52 Performing RAID Level Migration
- 53 Performing Stripe Size Migration
- 53 Extending the Capacity of a Logical Drive
- 53 Expanding the Capacity of an Array
- 53 Changing the Expand Priority
- 55 HP Support Tools Manager
- 55 Event Monitoring Service
- 55 ODE
- 56 The sautil Command
- 58 The sautil <device_file> command
- 62 Logical Drive State Definitions
- 63 Physical Disk State Definitions
- 63 The sautil <device_file> scan Command
- 63 The sautil <device_file> accept_media_xchg <logical_drive_number> Command
- 64 The sautil <device_file> set_transfer_rate <rate> Command
- 64 The sautil <device_file> run_startup_script Command
- 65 Smart Array 6400 Series Controller Specifications
- 67 Overview
- 67 Physical Disk Failure
- 67 Recognizing Disk Failure
- 70 Compromised Fault Tolerance
- 70 Recovering from Fault Tolerance Failures
- 70 Automatic Data Recovery
- 71 Physical Disk Replacement Overview
- 71 Physical Disk Failure During Rebuild
- 71 Minimizing Fatal System Errors During Rebuild
- 73 RAID Level and Probability of Drive Failure
- 75 Handling Parts
- 75 Grounding
- 77 Smart Array 6400 Series Controller FAQ