advertisement
8
User maintenance and cleaning instructions
8.1 Lint filter
Lint and fibers released from the laundry in to the air during the drying cycle are collected in the “Lint Filter”.
C
Fibres and lint are formed during wearing and washing.
WARNING: Always clean the filter after each drying cycle.
8.2 Sensor
There are humidity sensors in your dryer that detect whether the laundry is dry or not.
For sensor cleaning;
1. Open loading door.
2. Allow dryer to cool off if drying has been done recently.
3. Wipe the metal sensors with a soft cloth dampened with vinegar and dry the sensors afterwards.
To clean the Filter;
1. Open loading door.
2. Remove the lint filter by pulling it up and open the filter.
3. Clean lint, fiber, and by hand or with a soft piece of cloth.
4. Close the filter and put it back in place.
A
Clean the metal sensors at regular intervals (4 times a year).
WARNING: Never use solvents, cleaning agents or similar substances when cleaning as these might cause fire and/or an explosion!
C
You can clean the filter and filter area with a vacuum cleaner.
Clogging may arise on the filter surface after using your dryer for some time; if this occurs, wash the filter with water and dry it before using again.
Dryer / User Manual
24 / EN
9
Troubleshooting
Problem
Drying process takes too long.
Dryer does not switch on or the program does not start. Dryer does not start when set.
Program is interrupted for no reason.
Laundry has shrunk, become felted or has deteriorated.
Cause
Lint filter may not have been cleaned.
* It may not plugged in.
* The loading door may be ajar.
* Program may not be set or the
“Start/Pause/Cancel” button may not have been pressed.
* “Childproof lock” may be activated.
* The loading door may be ajar.
* Electricity may be cut off.
* A program not suitable for the laundry type might have been used.
Explanation / Solution
* Clean the lint filter.
* Meshes of the filter may be clogged. Wash with water.
* Make sure that the dryer is plugged in.
* Make sure the loading door is properly closed.
* Make sure the program has been set and it is not in “Pause” mode.
* Deactivate the childproof lock.
* Make sure the loading door is properly closed.
* Press the “Start/Pause/Cancel” button to start the program.
* Dry only the laundry which is suitable for drying in the dryer. First check the labels on the clothes.
* Select a program a suitable low temperature setting for the laundry type to dry the clothes.
“End / Anticrease”
LED flashes.
* The 2-hour anti creasing program to prevent laundry from wrinkling may have been activated.
* Turn off the dryer and take the laundry out of the dryer.
“End / Anticrease”
LED is on.
“Filter cleaning”
LED flashes.
* Program has come to an end.
* Lint filter may not have been cleaned.
The “Drying” LED flashes.
* A heat sensor failure has occurred. dryer ends the program without heating.
NOTE:
Call an authorized service if the problem persists.
* Turn off the dryerand take the laundry out of the dryer.
* Clean the lint filter.
* Meshes of the filter may be clogged. Wash with water.
* Turn off the dryer and remove the laundry. Call the authorized service.
Dryer / User Manual
25 / EN
1
0
Warranty Statement
This product is fully tested and went through official quality assurance inspections before leaving the original manufacturing site. Warranty terms for this
Blomberg household appliance is not valid if the product is altered, tampered, modifed, additional parts assembled, fixed and re-packed by an authorized distributor, servicer, a third party retailer, reseller or by any other unauthorized person(s).
26 / EN
Dryer / User Manual
Dryer / User Manual
27 / EN
www.blomberginternational.com
2960310298_EN/180117.1656
advertisement
Related manuals
advertisement