VRF Support. Cisco Unified Communications Manager Express Version 11.7 , Unified Communications Manager Express, Unified Communications Manager Express Version 12.5 , Unified Communications Manager Express Version 12.3 , Unified Communications Manager Express Version 14.0 , Unified Communications Manager Express Version 14.1 , Unified Communications Manager Express Version 12.0 , Unified Communications Manager Express Version 12.2 , Unified Communications Manager Express Version 11.5 , Unified Communications Manager Express Version 12.1
Iklan
Iklan
C H A P T E R
52
VRF Support
Virtual Route Forwarding (VRF) divides a physical router into multiple logical routers, each having its own set of interfaces and routing and forwarding tables. VRF support in voice networks can be used to split
Cisco Unified Communications Manager Express (Cisco Unified CME) into multiple virtual systems for
SIP and SCCP endpoints and TAPI-based client applications and softphones on your PC.
•
Prerequisites for Configuring VRF Support, page 1551
•
Restrictions for Configuring VRF Support, page 1553
•
Information About VRF Support, page 1554
•
Configure VRF Support, page 1554
•
Configuration Examples for Configuring VRF Support, page 1563
•
Feature Information for VRF Support, page 1569
Prerequisites for Configuring VRF Support
• For Multi-VRF support on SIP phones, Cisco Unified CME version has to be 10.5 and later.
• For Multi-VRF support on SCCP phones, Cisco Unified CME 7.0(1) or a later version must be configured on the Cisco router.
• VRF-Aware H.323 and SIP must be configured on the Cisco Unified CME router, including the following:
• Up to five VRFs must be configured on the Cisco Unified CME router by using the ip vrf command.
For configuration information, see VRF-Aware H.323 and SIP for Voice Gateways .
• One of the groups must be designated as a global voice VRF (SIP Trunk) by using thevoice vrf command. For configuration information, see VRF-Aware H.323 and SIP for Voice Gateways .
Example: voice vrf voice-vrf ip vrf data-vrf1 rd 801:1 route-target export 801:1
!
route-target import 1000:1 ip vrf data-vrf2
Cisco Unified Communications Manager Express System Administrator Guide
1551
VRF Support
Prerequisites for Configuring VRF Support
rd 802:1 route-target export 802:1
!
route-target import 1000:1 ip vrf voice-vrf
!
rd 1000:1 route-target export 1000:1 route-target import 801:1 route-target import 802:1
• Interfaces on the router must be configured for the VRFs by using the ip vrf forwarding command.
Note
Example:
Only global voice VRF is supported for SIP trunk.
interface GigabitEthernet0/0.301
encapsulation dot1Q 301 ip vrf forwarding data-vrf1 ip address 10.1.10.1 255.255.255.0
!
interface GigabitEthernet0/0.302
encapsulation dot1Q 302 ip vrf forwarding data-vrf1
!
ip address 10.2.10.1 255.255.255.0
interface GigabitEthernet0/0.303
encapsulation dot1Q 303 ip vrf forwarding voice-vrf ip address 10.3.10.1 255.255.255.0
• VRFs must be mapped to IP addresses using DHCP. For configuration information, see
on page 122 .
Example:
!<=== no ip dhcp command required only if
“ip vrf forward” is specified under ip dhcp no ip dhcp use vrf connected pool===>
!<=== Associate subnets with VRFs. Overlapping IP addresses are NOT supported.===> ip dhcp pool vcme1 network 10.1.10.0 255.255.255.0
default-router 10.1.10.1
option 150 ip 10.1.10.1
class vcme1 address range 10.1.10.10 10.1.10.250
!
ip dhcp pool vcme2 network 10.2.10.0 255.255.255.0
default-router 10.2.10.1
option 150 ip 10.2.10.1
class vcme2 address range 10.2.10.10 10.2.10.250
For more configuration examples, see
Example for Mapping IP Address Ranges to VRF Using DHCP,
on page 1563 .
• Dial peers for H323 and SIP trucks must be routed through the global voice VRF.
1552
Cisco Unified Communications Manager Express System Administrator Guide
VRF Support
Restrictions for Configuring VRF Support
Note
Dial peers are global resources belonging to the voice VRF and shared with and accessible from any VRF. There is no need to configure a dial peer for each individual
VRF.
Restrictions for Configuring VRF Support
• Multi-VRF is not supported on Cisco 4000 Series Integrated Services Routers for Unified CME.
• For SIP phones in Cisco Unified CME: SIP proxy and registrar must be in the same VRF.
• IP-address overlap between VRFs is not supported.
• Cross-VRF video is not supported.
• The following call types are not supported for a voice VRF:
◦IP-to-IP gateway and gatekeeper configured on the same router.
◦IP-to-IP gateway with a VRF configured on one call leg and not on another call leg.
◦IP-to-IP gateway with one VRF configured for the H.323 call leg and a different VRF configured for the SIP call leg.
◦For H.323 calls, only TCP is supported. H.323 UDP signaling is not supported. SIP calls support both TCP and UDP signaling.
• The following features are not supported by on a VRF:
◦Call-fallback and RSVP features.
◦H.323 Annex E calls.
◦AAA and DNS components in voice-capable access routers. These routers communicate with AAA and DNS using the default routing table.
• If a global voice VRF is not configured, signaling and media packets are sent using the default routing table.
• Only the global voice VRF is supported for SIP trunk.
• Cisco Unity Express on the Cisco Unified CME router must belong to the global voice VRF.
Note
Telnet is used to access Cisco Unity Express on the global voice VRF because the Service-Engine
Service-Engine 1/0 session command is for non-VRF aware Cisco Unified CME only. To access the
Cisco Unity Express module for defining voice-mail users on global voice VRF, telnet through the global voice VRF. For example: telnet 10.10.10.5 2066 /vrf vrf. For more information, see the “Installing
Cisco Unity Express Software” chapter in the appropriate Cisco Unity Express Administrator Guide for
Cisco Unified CME .
Cisco Unified Communications Manager Express System Administrator Guide
1553
VRF Support
Information About VRF Support
Information About VRF Support
VRF-Aware Cisco Unified CME
VRF implementations enable you to consolidate voice communication into one logically-partitioned network to separate voice and data communication on a converged multimedia network.
VRF-Aware Cisco Unified CME for SCCP Phones
In Cisco Unified CME 7.0(1) and later versions, VRF in voice networks can be used to share a
Cisco Unified CME among multiple closed-users groups with different requirements. The actual call processing rules can be applied by voice on a per VRF basis. A virtual Cisco Unified CME on each VRF is a collection of phones in VRF groups that register in Cisco Unified CME through the VRF. All SCCP and SIP phones connected to Cisco Unified CME register through the global voice VRF. TAPI-based client applications and softphones on a PC must register through a data VRF and can communicate with phones on the voice VRF.
VRF Support on Cisco Unified CME provides the following enhancements to the VRF-Aware H.323 and SIP for Voice Gateways feature:
• Line side support for up to 5 VRFs.
• Interworks with the global voice VRF on an H323 or SIP Trunk.
• Line side VRF can be a global voice VRF.
• VRFs are assigned on a per-phone level.
• Support for cross-VRF shared-lines.
For configuration information, see
Configure VRF Support, on page 1554
.
Multi-VRF Support on Cisco Unified CME for SIP Phones
The Multi-VRF support on Cisco Unified CME for SIP Phones, provides the following enhancements:
• Up to 5 VRF groups can be configured on SIP line side under voice register global.
• Under voice register pool, we can configure a VRF group to which the phone is associated with.
• All SIP signaling and media traffic between CME and the phones would be routed on the specified VRF.
Configure VRF Support
Create VRF Groups for SCCP Phones
To configure up to five VRF groups for users and phones in Cisco Unified CME, perform the following steps for each group to be configured.
1554
Cisco Unified Communications Manager Express System Administrator Guide
VRF Support
Create VRF Groups for SCCP Phones
SUMMARY STEPS
1. enable
2. configure terminal
3. telephony-service
4. group group-tag [vrf vrfname]
5. ip source-address ip-address [ port port]
6. url {authentication | directories |idle | information | messages | proxy-server |services} url
7. service phone webAccess 0
8. end
DETAILED STEPS
Step 1
Step 2
Step 3
Step 4
Step 5
Command or Action enable
Example:
Router> enable
configure terminal
Example:
Router# configure terminal
telephony-service
Example:
Router(config)# telephony-service
group group-tag [vrf vrfname]
Example:
Router(config-telephony)# group 1
Purpose
Enables privileged EXEC mode.
• Enter your password if prompted.
Enters global configuration mode.
Enters telephony-service configuration mode.
Creates a VRF group for Cisco Unified CME users and phones.
• group-tag—Unique identifier for VRF group being configured. Range: 1 to 5.
• (Optional) vrf vrfname—Name of previously configured
VRF to which this group is associated.
• By default, VRF groups are associated with a global voice
VRF unless otherwise specified by using the vrfvrfname keyword and argument combination.
ip source-address ip-address [ port port]
Example:
Router(conf-tele-group)# ip source-address
10.1.10.1 port 2000
Associates VRF group with Cisco Unified CME.
• ip address and port through which Cisco Unified IP phones communicate with Cisco Unified CME.
Cisco Unified Communications Manager Express System Administrator Guide
1555
VRF Support
Create VRF Groups for SIP Phones
Step 6
Step 7
Step 8
Command or Action Purpose
url {authentication | directories |idle |
information | messages | proxy-server |services}
url
Provisions uniform resource locators (URLs) for Cisco Unified
IP phones connected to Cisco Unified CME.
Example:
Router(conf-tele-group)# url directories http://10.1.10.1/localdirectory
service phone webAccess 0
Enables webAccess for IP phones. This is required for 9.x
firmware, since the web server is disabled by default. 8.x firmware and lower had the web server enabled by default.
Example:
Router(conf-tele-group)# service phone webAccess 0
end
Returns to privileged EXEC mode.
Example:
Router(conf-tele-group)# end
Examples
The following partial output from the show running-config commands shows how to define three VRF groups for Cisco Unified CME. Group 1 is on the global voice VRF and the other two groups are on data VRFs.
telephony-service sdspfarm conference mute-on # mute-off # sdspfarm units 4 sdspfarm transcode sessions 10 sdspfarm tag 1 xcode101 sdspfarm tag 2 conf103 group 1 ip source-address 10.1.10.1 port 2000
!
url directories http://10.1.10.1/localdirectory group 2 vrf data-vrf1 ip source-address 10.2.10.1 port 2000
!
group 3 vrf data-vrf2 ip source-address 10.3.10.1 port 2000
Create VRF Groups for SIP Phones
In Cisco Unified CME 10.5 release the VRF support for SIP phones is added. Up to five VRF groups can be configured on SIP line side under voice register global. Under voice register pool, we can configure VRF group to which the phone is associated with. To configure VRF support, perform the following steps:
1556
Cisco Unified Communications Manager Express System Administrator Guide
VRF Support
Create VRF Groups for SIP Phones
SUMMARY STEPS
1. enable
2. configure terminal
3. voice register global
4. group group-tag [vrf vrfname]
5. source-address ip-address
6. url {authentication | directory | service} url
7. exit
DETAILED STEPS
Step 1
Step 2
Step 3
Step 4
Step 5
Command or Action enable
Purpose
Enables privileged EXEC mode.
• Enter your password if prompted.
Example:
Router> enable
configure terminal
Enters global configuration mode.
Example:
Router# configure terminal
voice register global
source-address ip-address
Enters voice register global configuration mode.
Example:
Router(config)# voice register global
group group-tag [vrf vrfname]
Example:
Router(config-register-global)# group
1
Creates a VRF group for Cisco Unified CME users and phones.
• group-tag—Unique identifier for VRF group being configured.
Range: 1 to 5.
• (Optional) vrf vrfname—Name of previously configured VRF to which this group is associated.
• By default, this group is not associated with any VRF unless otherwise specified by using the vrf vrfname keyword and argument combination.
• Defines unique identifiers group between 1 to 5, which can then be applied on individual pools.
Note
Use the shutdown command to temporarily shutdown the group without effecting the other groups. Use the no form of the command to enable the group.
• The default behavior is no shut.
Associates VRF group with Cisco Unified CME.
Cisco Unified Communications Manager Express System Administrator Guide
1557
VRF Support
Add Cisco Unified CME SCCP Phones to a VRF Group
Step 6
Step 7
Command or Action Purpose
• ip address through which Cisco Unified IP phones communicate with Cisco Unified CME.
Example:
Router(config-voice-register-group)# source-address 10.1.10.1
url {authentication | directory | service} url Provisions uniform resource locators (URLs) for Cisco Unified IP phones connected to Cisco Unified CME.
Example:
Router(config-voice-register-group)# url directory http://10.1.10.1/localdirectory
exit
Exits to privileged EXEC mode.
Example:
Router(config-voice-register-group)# exit
Examples
The following sample output displays how to configure SIP CME support for VRF by provisioning its source address under a group: voice register global or voice register dn or voice register pool mode cme max-dn 100 max-pool 100 group 1 vrf voice-vrf1 source-address 8.0.0.1
Add Cisco Unified CME SCCP Phones to a VRF Group
To add an SCCP Cisco Unified IP phone, TAPI-based client, or softphone in Cisco Unified CME to a VRF group, perform the following steps for each phone to be added.
1558
Cisco Unified Communications Manager Express System Administrator Guide
VRF Support
Add Cisco Unified CME SCCP Phones to a VRF Group
Restriction
• All SCCP phones in Cisco Unified CME must register through the global voice VRF and must be added to the VRF group on the global voice VRF only.
• Analog phones connected to FXS ports on a IOS gateway must register through the global voice
VRF and must be added to the VRF group on the global voice VRF only.
• TAPI-based client applications and softphones on a PC must register through the data VRF and must be added to a VRF group on a data VRF only.
• VRF groups do not support identical IP addresses or shared lines.
Before You Begin
• All ephone configurations to be included in a VRF group must be already configured in
Cisco Unified CME. For configuration information, see
Configure Phones to Make Basic Call, on page
315 .
SUMMARY STEPS
1. enable
2. configure terminal
3. ephone phone-tag
4. description string
5. mac-address [mac-address]
6. group phone group-tag [tapi group-tag]
7. end
DETAILED STEPS
Step 1
Step 2
Step 3
Command or Action enable
Example:
Router> enable
configure terminal
Example:
Router# configure terminal
ephone phone-tag
Example:
Router(config)# ephone 11
Purpose
Enables privileged EXEC mode.
• Enter your password if prompted.
Enters global configuration mode.
Enters ephone configuration mode for a Cisco Unified IP phone.
Cisco Unified Communications Manager Express System Administrator Guide
1559
VRF Support
Add Cisco Unified CME SCCP Phones to a VRF Group
Step 4
Step 5
Step 6
Step 7
Command or Action
description string
Example:
Router(config-ephone)# description cme-2801 srst
mac-address [mac-address]
Example:
Router(config-ephone)# mac-address
0012.8055.d2EE
group phone group-tag [tapi group-tag]
Example:
Router(config-ephone)# group phone 1
Purpose
(Optional) Includes descriptive text about the interface.
Associates the MAC address of a Cisco Unified IP phone with an ephone configuration.
Adds a phone, TAPI-based client, or softphone to a VRF group.
• group-tag—Unique identifier for VRF group that was previously configured by using the group command in telephony-service configuration mode. Range: 1 to 5.
• This command can also be configured in ephone-template configuration mode and applied to one or more phones. The ephone configuration has priority over the ephone-template configuration.
Returns to privileged EXEC mode.
end
Example:
Router(config-ephone)# end
Examples
The following example shows how to add phones to VRF groups. Phones 1 and 3 are in VRF group 1 on the global voice VRF. Phone 1 TAPI client and softphone 3 are in group 1 on the data-vrf2. Phone 3 TAPI client and softphone 4 are in group 3 on data-vrf 2.
telephony-service sdspfarm conference mute-on # mute-off # sdspfarm units 4 sdspfarm transcode sessions 10 sdspfarm tag 1 xcode101 sdspfarm tag 2 conf103 group 1 vrf voice-vrf ip source-address 10.1.10.1 port 2000 url directories http://10.1.10.1/localdirectory
!
group 2 vrf data-vrf1
!
ip source-address 10.2.10.1 port 2000 group 3 vrf data-vrf2
.
.
!
ip source-address 10.3.10.1 port 2000 ephone-template 1
1560
Cisco Unified Communications Manager Express System Administrator Guide
VRF Support
Add Cisco Unified CME SIP Phones to a VRF Group
group phone 1 tapi 2 ephone-template 2 group phone 2
...
ephone 1 ephone-template 1 ephone 2 ephone-template 2 ephone 3 group phone 1 tapi 3 ephone 4 group phone 3 ephone 201 group phone 1 type anl
Add Cisco Unified CME SIP Phones to a VRF Group
To add an SIP Cisco Unified IP phone, or softphone in Cisco Unified CME to a VRF group, perform the following steps for each phone to be added.
Before You Begin
• All voice register pool configurations to be included in a VRF group must be already configured in
Cisco Unified CME. For configuration information, see
Configure Phones to Make Basic Call, on page
315 .
SUMMARY STEPS
1. enable
2. configure terminal
3. voice register pool pool-tag
4. id mac [mac-address]
5. group group-tag
6. end
DETAILED STEPS
Step 1
Step 2
Command or Action enable
Example:
Router> enable
configure terminal
Example:
Router# configure terminal
Purpose
Enables privileged EXEC mode.
• Enter your password if prompted.
Enters global configuration mode.
Cisco Unified Communications Manager Express System Administrator Guide
1561
VRF Support
Add Cisco Unified CME SIP Phones to a VRF Group
Step 3
Step 4
Step 5
Step 6
Command or Action
voice register pool pool-tag
Example:
Router(config-register-pool)# group
id mac [mac-address]
Example:
Router(config-regoster-pool)# id mac
0012.8055.d2EE
group group-tag
Example:
Router(config-register pool)# group 1
end
Example:
Router(config-register-pool)# end
Purpose
Enters voice reigster pool configuration mode for a
Cisco Unified IP phone.
Associates the MAC address of a Cisco Unified IP phone with an voice register pool configuration.
Adds a phone, or softphone to a VRF group.
• group-tag—Unique identifier for VRF group that was previously configured by using the group command in voice register global configuration mode. Range: 1 to 5.
Returns to privileged EXEC mode.
Examples
The following example shows how to add SIP phones to VRF groups.
voice register global mode cme max-dn 100 max-pool 100 authenticate realm ccmsipline voicemail 24001 phone-mode phone-only tftp-path flash: create profile sync 0000443960010126 conference hardware group 1 vrf voice-vrf1 source-address 8.0.0.1
!
group 2 vrf data-vrf1
!
url authentication http://7.0.0.1/CCMCIP/authenticate.asp
source-address 7.0.0.1
group 3 vrf data-vrf1 source-address 10.104.45.142
!
group 4 vrf voice-vrf1
!
source-address 9.42.29.101
!
voice register pool 1 id mac A40C.C395.7B5C
session-transport tcp type 9971 number 1 dn 1 group 1 template 1
1562
Cisco Unified Communications Manager Express System Administrator Guide
VRF Support
Configuration Examples for Configuring VRF Support
!
dtmf-relay rtp-nte username 14001 password 14001 codec g711ulaw paging-dn 99
Configuration Examples for Configuring VRF Support
Example for Mapping IP Address Ranges to VRF Using DHCP
Note
Duplicate IP addresses, with or without specifying a VRF, are not supported in Cisco Unified CME 7.0(1).
There are three ways to assign DHCP addresses: global address allocation; VRF pool; or individual host
With a global address allocation scheme, you must use the no ip dhcp use vrf connected command.
no ip dhcp use vrf connected
!
ip dhcp pool vcme1 network 209.165.201.10 255.255.255.224
option 150 ip 209.165.201.9
default-router 209.165.201.9
class vcme1 address range 209.165.201.1 209.165.201.30
!
The following example shows how to assign addresses from VRF pool vcme1.
ip dhcp use vrf connected
!
ip dhcp pool vcme1 vrf data-vrf1 network 209.165.201.10 255.255.255.224
option 150 ip 209.165.201.9
default-router 209.165.201.9
class vcme1 address range 209.165.201.1 209.165.201.30
!
The following example show how to assign an address by an individual host. You must replace the first two hexadecimal digits of a host MAC address with 01.
ip dhcp pool phone3 host 209.165.201.15 255.255.255.224
client-identifier 0100.0ed7.4ce6.3d
default-router 209.165.201.11
option 150 ip 209.165.201.11
!
Example for Configuring VRF-Aware Hardware Conferencing
Hardware Conferencing with Internal DSP Farm
• The internal DSPFarm must be registered through a local loopback interface.
Cisco Unified Communications Manager Express System Administrator Guide
1563
VRF Support
Example for Configuring Cisco Unity Express on Global Voice VRF
• The loopback allows Cisco Unified CME to access the media path in global routing table.
The boldface commands in the following configuration example show that the signaling and media paths are accessed through the global routing table and the loopback interface is in default routing table.
interface Loopback5
!
ip address 12.5.10.1 255.255.255.255
sccp local Loopback5
sccp ccm 12.5.10.1 identifier 2 version 4.1
sccp
!
sccp ccm group 2
bind interface Loopback5
associate ccm 2 priority 1 associate profile 103 register conf103 associate profile 101 register xcode101
!
telephony-service sdspfarm conference mute-on # mute-off # sdspfarm units 4 sdspfarm transcode sessions 10 sdspfarm tag 1 xcode101 sdspfarm tag 2 conf103 group 1 vrf vrf1 ip source-address 10.1.10.1 port 2000
!
group 2 vrf vrf2 ip source-address 10.2.10.1 port 2000
!
group 3 vrf vrf3 ip source-address 10.3.10.1 port 2000
!
group 4 vrf vrf4 ip source-address 10.4.10.1 port 2000
!
group 5 ip source-address 12.5.10.1 port 2000
!
conference hardware max-ephones 240 max-dn 480 voicemail 7710 max-conferences 8 gain -6
Hardware Conferencing with External DSP Farm
• Configure DSP farm as usual on a Cisco router.
• The external DSP farm must be registered to Cisco Unified CME through the interface or subinterface assigned to the global voice VRF. Make sure the connection path is coming in through the voice VRF.
• The router on which the external DSP farm is configured does not have to be VRF-aware.
For information about configuring DSP Farms, see
Configure Transcoding Resources, on page 477
.
Example for Configuring Cisco Unity Express on Global Voice VRF
voice vrf vrf2 ip vrf data-vrf2 rd 100:2 route-target export 100:2
1564
Cisco Unified Communications Manager Express System Administrator Guide
VRF Support
Example for Configuring Cisco Unity Express on Global Voice VRF
!
route-target import 100:2
Interface loop back 0 ip vrf forwarding data-vrf2
Ip address 21.10.10.2
!<==The following config puts CUE in the voice vrf. Service-engine interface and service-module must have an IP address.===>
!
interface Service-Engine1/0 ip vrf forwarding voice-vrf3 ip address 21.10.10.5 255.255.255.0
service-module ip address 21.10.10.6 255.255.255.0
service-module ip default-gateway 21.10.10.2!
ip route 21.10.10.6 255.255.255.255 Service-Engine1/0
… line 66 no activation-character
Hardware Conferencing with Internal DSP Farm
• The internal DSPFarm must be registered through a local loopback interface.
• The loopback allows Cisco Unified CME to access the media path in global routing table.
The boldface commands in the following configuration example show that the signaling and media paths are accessed through the global routing table and the loopback interface is in default routing table.
interface Loopback5
!
ip address 12.5.10.1 255.255.255.255
sccp local Loopback5
sccp ccm 12.5.10.1 identifier 2 version 4.1
sccp
!
sccp ccm group 2
bind interface Loopback5
associate ccm 2 priority 1 associate profile 103 register conf103 associate profile 101 register xcode101
!
telephony-service sdspfarm conference mute-on # mute-off # sdspfarm units 4 sdspfarm transcode sessions 10 sdspfarm tag 1 xcode101 sdspfarm tag 2 conf103 group 1 vrf vrf1 ip source-address 10.1.10.1 port 2000
!
group 2 vrf vrf2 ip source-address 10.2.10.1 port 2000
!
group 3 vrf vrf3 ip source-address 10.3.10.1 port 2000
!
group 4 vrf vrf4 ip source-address 10.4.10.1 port 2000
!
group 5 ip source-address 12.5.10.1 port 2000
!
conference hardware max-ephones 240 max-dn 480 voicemail 7710 max-conferences 8 gain -6
Hardware Conferencing with External DSP Farm
Cisco Unified Communications Manager Express System Administrator Guide
1565
VRF Support
Example for Configuring Multi- VRF Support for Cisco Unified CME SIP Phones
• Configure DSP farm as usual on a Cisco router.
• The external DSP farm must be registered to Cisco Unified CME through the interface or subinterface assigned to the global voice VRF. Make sure the connection path is coming in through the voice VRF.
• The router on which the external DSP farm is configured does not have to be VRF-aware.
For information about configuring DSP Farms, see
Configure Transcoding Resources, on page 477
.
Example for Configuring Multi- VRF Support for Cisco Unified CME SIP Phones
The following sample output displays CME configuration which enables the user to accept registrations from multiple VRFs.
voice register global mode cme max-dn 100 max-pool 100 authenticate realm ccmsipline voicemail 24001 phone-mode phone-only tftp-path flash: create profile sync 0000443960010126 conference hardware group 1 vrf voice-vrf1 source-address 8.0.0.1
!
group 2 vrf data-vrf1 url authentication http://7.0.0.1/CCMCIP/authenticate.asp
!
source-address 7.0.0.1
group 3 vrf data-vrf1 source-address 10.104.45.142
!
group 4 vrf voice-vrf1 source-address 9.42.29.101
!
!
voice register dn 1 number 14001
!
name voicevrf-ph1 voice register dn 2 number 14002
!
allow watch name datavrf-ph1 voice register dn 3 number 14003 allow watch name voicevrf-ph2
!
voice register dn 4 voice-hunt-groups login number 14004 name Jabber-Win
!
voice register dn 5
!
number 14005 name Jabber-Android voice register dn 6 number 14006 allow watch mobility
!
snr 24001 delay 5 timeout 50
1566
Cisco Unified Communications Manager Express System Administrator Guide
VRF Support
Example for Configuring Multi- VRF Support for Cisco Unified CME SIP Phones
voice register dn 7 number 14007
!
name voicevrf-7841 voice register dn 8 number 14008 name jabbed-android-2
!
voice register dn 10 number 14010 allow watch name intervrf-shared-line shared-line max-calls 8
!
voice register dn 11 number 14011 shared-line
!
voice register dn 12 number 15002 name em-logged-in
!
voice register dn 21 number 1101 name CME1-Phone1
!
voice register dn 22 number 1102 name CME1-Phone2
!
voice register template 1 softkeys idle Newcall Pickup Redial Cfwdall DND softkeys ringIn Answer DND iDivert softkeys connected Endcall Hold Mobility iDivert Park
!
voice register pool 1 id mac A40C.C395.7B5C
session-transport tcp type 9971 number 1 dn 1 group 1 template 1 dtmf-relay rtp-nte username 14001 password 14001 codec g711ulaw
!
paging-dn 99 voice register pool 2 fastdial 1 14003 name voice-vrf1-ph1 id mac ACA0.16FC.9742
type 9971 number 1 dn 2 number 2 dn 10 group 2 template 1 presence call-list dtmf-relay rtp-nte codec g711ulaw paging-dn 99 blf-speed-dial 1 13001 label "13001" blf-speed-dial 2 14006 label "14006"
!
voice register pool 3 fastdial 1 14002 name datavrf,ph1 id mac 2893.FEA3.2557
type 9951 number 1 dn 3 number 2 dn 10 group 1 template 1 dtmf-relay rtp-nte username 14003 password 14003 codec g711ulaw
Cisco Unified Communications Manager Express System Administrator Guide
1567
Example for Configuring Multi- VRF Support for Cisco Unified CME SIP Phones
blf-speed-dial 1 14002 label "14002" blf-speed-dial 2 14006 label "14006"
!
blf-speed-dial 3 13001 label "13001" voice register pool 4 id device-id-name arunsrin type Jabber-CSF-Client number 1 dn 4 group 3 dtmf-relay rtp-nte username arunsrin password cisco codec g711ulaw
!
voice register pool 5 registration-timer max 720 min 660 id mac 980C.821B.26CD
session-transport tcp type Jabber-Android number 1 dn 5 group 3 dtmf-relay rtp-nte username frodo password cisco codec g711ulaw
!
voice register pool 6 busy-trigger-per-button 40 id mac 6C41.6A36.900D
type 7821 number 1 dn 6 group 1 template 1 presence call-list dtmf-relay rtp-nte codec g711ulaw
!
paging-dn 99 voice register pool 7 busy-trigger-per-button 40 id mac 6C41.6A36.9110
session-transport tcp type 7841 number 1 dn 7 group 2 dtmf-relay rtp-nte codec g711ulaw
!
paging-dn 99 voice register pool 8 registration-timer max 720 min 660 id mac 980C.821A.5D28
session-transport tcp type Jabber-Android number 1 dn 8 group 3 dtmf-relay rtp-nte username pippin password cisco codec g711ulaw
!
voice register pool 21 id mac 1000.1000.1101
type 7970 number 1 dn 21 group 4 username 1101 password 1101
!
codec g711ulaw voice register pool 22 id mac 1000.1000.1102
type 7970 number 1 dn 21 group 4 username 1102 password 1102 codec g711ulaw
1568
Cisco Unified Communications Manager Express System Administrator Guide
VRF Support
VRF Support
Feature Information for VRF Support
!
voice hunt-group 1 parallel phone-display final 13002 list 14001,14002,14003 timeout 3 pilot 14999
!
!
voice hunt-group 2 parallel final 14001 list 14004,*,14002 timeout 5 pilot 14998 name test-vhg
!
!
voice logout-profile 1 pin 1234 user 14002 password 14002 number 14002 type normal speed-dial 1 13002 label "ephone2"
!
!
!
!
voice user-profile 1 user me password me number 15002 type normal voice translation-rule 217351 rule 1 /^24/ /9924\1/
!
!
voice translation-profile 217351
Feature Information for VRF Support
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support.
To access Cisco Feature Navigator, go to www.cisco.com/go/cfn . An account on Cisco.com is not required.
Table 119: Feature Information for Virtual Route Forwarding
Feature Name
VRF Support in
Cisco Unified CME
Cisco Unified CME Version
7.0(1)
Feature Information
VRF supports Cisco Unified CME, conferencing, transcoding, and
RSVP components. VRF also allows soft phones in data VRF resources to communicate with phones in a VRF voice gateway.
Cisco Unified Communications Manager Express System Administrator Guide
1569
Feature Information for VRF Support
VRF Support
1570
Cisco Unified Communications Manager Express System Administrator Guide
Unduh
Tautan publik diperbarui
Tautan publik ke obrolan Anda telah diperbarui. You may view and manage your chat links after registration here.
Tautan publik dokumen
Iklan