advertisement
Table of
C O N T E N T S
Safety Definitions ....................................................... 4
IMPORTANT SAFETY INSTRUCTIONS ........................ 5
Burn Prevention .............................................................. 6
Saving Energy ................................................................. 8
Accessories ................................................................. 9
Getting to Know the Appliance ................................ 10
Control Panel ................................................................ 11
Before First Use ........................................................ 14
Initial Use ....................................................................... 15
Calibrating the Appliance and Cleaning the
Oven Cavity ................................................................... 15
General Operation ................................................... 17
Setting a Heating Mode ............................................... 18
Inserting Accessories .................................................... 23
Steam Operation ..................................................... 24
Proof .............................................................................. 25
After Every Steam Operation ........................................ 27
Steam Programs ............................................................ 28
Home Connect ......................................................... 30
Setting Up ..................................................................... 30
Wi-Fi ®
Module .............................................................. 34
Cleaning Your Oven ................................................. 34
Suitable Cleaning Agents ............................................. 34
Service ..................................................................... 39
Troubleshooting Chart .................................................. 39
STATEMENT OF LIMITED PRODUCT WARRANTY ... 42
THERMADOR® Support .......................................... 43
4
Safety Definitions
Safety Definitions 9
WARNING
This indicates that death or serious injuries may occur as a result of non-observance of this warning.
9
CAUTION
This indicates that minor or moderate injuries may occur as a result of non-observance of this warning.
NOTICE:
This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.
Note:
This alerts you to important information and/or tips.
advertisement
Related manuals
advertisement
Table of contents
- 3 Table of ContentsUse and care manual
- 4 Safety DefinitionsSafety Definitions
- 4 9 WARNING
- 4 9 CAUTION
- 4 NOTICE:
- 4 Note:
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 5 READ AND SAVE THESE INSTRUCTIONS
- 5 WARNING
- 5 Proper Installation and Maintenance
- 5 WARNING
- 5 WARNING
- 5 Fire Safety
- 5 WARNING
- 5 WARNING
- 6 WARNING
- 6 TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A GREASE FIRE, OBSERVE THE FOLLOWING:
- 6 a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
- 6 b. NEVER PICK UP A FLAMING PAN – You may be burned.
- 6 c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
- 6 d. Use an extinguisher ONLY if:
- 6 Burn Prevention
- 6 CAUTION
- 6 WARNING
- 6 Scalding hazard
- 6 WARNING
- 6 Risk of scalding
- 6 WARNING
- 6 Risk of scalding
- 6 WARNING
- 6 Risk of burns
- 6 WARNING
- 6 Risk of scalding
- 7 Child Safety
- 7 WARNING
- 7 Cleaning Safety
- 7 WARNING
- 7 Risk of injury
- 7 WARNING
- 7 Risk of electrical shock
- 7 Cookware Safety
- 7 WARNING
- 7 Risk of electric shock
- 7 State of California Proposition 65 Warning:
- 7 WARNING
- 8 Causes of Damage
- 8 NOTICES
- 8 Protecting the Environment
- 8 Saving Energy
- 9 Accessories
- 9 9 CAUTION
- 9 Accessories Included
- 9 Note:
- 9 Special Accessories (not included)
- 10 Getting to Know the Appliance
- 10 Note:
- 10 Oven Overview
- 10 Oven Cavity
- 10 9 CAUTION
- 10 9 CAUTION
- 10 Oven Cavity Features
- 10 Oven Vent
- 10 Cooling Fan
- 10 Convection Fan
- 10 Oven Light
- 10 Water Tank
- 11 Control Panel
- 11 Operating Controls
- 11 Touch Buttons
- 11 Full Touch Color Display
- 11 Basic way of operating the display:
- 12 In some instances you have further options to navigate through the menu:
- 12 Main Menu
- 12 Heating Modes Menu
- 14 Before First Use
- 14 Before Using the Appliance for the First Time
- 14 Water Hardness
- 14 NOTICES
- 15 Initial Use
- 15 Setting the time of day
- 15 1. Touch the bottom line.
- 15 2. Touch the “Hours” touch field and swipe to the left or right to select the current hour.
- 15 3. Touch the "Minutes" touch field and swipe to the left or right to select the current minute.
- 15 4. Touch the 8 symbol to apply the settings.
- 15 Setting the language
- 15 1. Touch the bottom line.
- 15 2. Swipe to the left or right to select the required language.
- 15 3. Touch the top line.
- 15 Setting the Clock Display
- 15 1. Touch "Clock display".
- 15 2. Touch the bottom line.
- 15 3. Swipe to the left or right to select “digital” or “analogue”.
- 15 4. Touch the top line.
- 15 Setting the water hardness
- 15 1. Touch "Water hardness".
- 15 2. Touch the bottom line.
- 15 3. Swipe to the left or right to select the appropriate water hardness.
- 15 4. Touch the top line.
- 15 Setting up Home Connect
- 15 1. Touch “Home Connect”.
- 15 2. Touch “Start assistant”.
- 15 3. Follow the instructions in the chapter “Home Connect”.~ "Home Connect" on page 30
- 15 Note:
- 15 Notes
- 15 Calibrating the Appliance and Cleaning the Oven Cavity
- 15 Preparing the Appliance for Calibration
- 15 1. Remove the accessories from the oven cavity.
- 15 2. Remove any remaining packaging, such as polystyrene pellets, from the oven cavity.
- 15 3. Before calibrating the appliance, wipe the smooth surfaces in the oven cavity with a soft, wet cloth.
- 15 Notes
- 15 NOTICE:
- 16 1. Fill the water tank.
- 16 2. Press the ON l OFF touch button to switch on the appliance.
- 16 3. The oven will calibrate automatically after running a Steam heating mode at 212° F (100 °C) for 30 minutes. Set the heating mode, temperature and duration for the calibration. Press START to begin the appliance operation.
- 16 4. After calibration, allow the appliance to cool down.
- 16 5. Dry the oven cavity bottom floor.
- 16 6. Set Bake to 475° F (245°C).
- 16 7. Keep the kitchen ventilated while the appliance is heating.
- 16 8. Stop the appliance operation after the indicated duration. Use the ON l OFF touch button to switch off the appliance.
- 16 9. Wait until the oven cavity has cooled down.
- 16 10. Clean the smooth surfaces with soapy water and a dish cloth.
- 16 11. Empty the water tank and dry the oven cavity.
- 16 Note:
- 16 Cleaning the Accessories
- 16 Adjust Basic Settings
- 16 Changing the Settings
- 16 1. Touch the ON l OFF touch button.
- 16 2. Touch the MENU touch button.
- 16 3. Swipe to the left or right to select "Settings 4".
- 16 4. Touch “Continue”.
- 16 5. Swipe to the left or right to select the desired setting.
- 16 6. Touch the bottom touch field.
- 16 7. Swipe to the left or right to select the desired setting.
- 16 8. Touch the 8 icon (where applicable) to apply the setting.
- 16 9. Touch the MENU touch button.
- 16 10. Touch "Save" to save the changes.
- 16 Available Settings
- 17 General Operation
- 17 High Altitude Baking
- 17 Switching the Appliance On and Off
- 17 Notes
- 17 Timer Options
- 17 Displaying and hiding timer options
- 17 Note:
- 17 Oven Timer
- 17 1. Touch the ON l OFF touch button.
- 17 2. Set the heating mode and temperature.
- 17 3. Touch the TIMERS touch button.
- 17 4. Touch the “+ Oven Timer” touch field.
- 17 5. Touch the required field and swipe to the left or right to set the oven timer.
- 17 6. Touch the 8 symbol.
- 17 7. Touch the START l STOP touch button.
- 17 Note:
- 18 Kitchen Timer
- 18 1. Touch the TIMERS touch button.
- 18 2. Swipe to the left or right to select the timer value. You can set hours, minutes and seconds.
- 18 3. Touch the 8 icon.
- 18 Note:
- 18 Delayed Operation - "End time"
- 18 Notes
- 18 9 CAUTION
- 18 1. Place the food onto the appropriate accessory in the oven cavity and close the appliance door.
- 18 2. Touch the ON l OFF touch button.
- 18 3. Set the heating mode.
- 18 4. Touch the TIMERS touch button. The timer options are shown in the display.
- 18 5. Select Oven Timer and set a cook time. Touch the 8 icon.
- 18 6. Select TIMERS again and set End Time. Touch the 8 icon.
- 18 7. Touch the START l STOP touch button.
- 18 Checking, changing or deleting settings
- 18 1. Touch the TIMERS touch button.
- 18 2. Touch the required timer option.
- 18 3. Swipe to the left or right on the touch display to change the settings.
- 18 Setting a Heating Mode
- 18 1. Touch the ON l OFF touch button to switch on the appliance.
- 18 2. Swipe to the left in the top line of the display to select “True Convection” ‚.
- 18 3. Swipe to the left or right in the bottom line of the display to select the temperature.
- 19 4. Touch the START l STOP touch button to start the appliance operation.
- 19 Default Values
- 19 Preheating Bar
- 19 INFO Touch Button
- 19 Sounds
- 19 Changing or Cancelling the Appliance Operation
- 19 Note:
- 19 Changing the appliance operation
- 19 1. Use the START l STOP touch button to stop the operation.
- 19 2. Touch the area for the setting that should be changed.
- 19 3. Swipe to the left or right to change the setting.
- 19 4. Use the START l STOP touch button to start the changed operation.
- 19 Notes
- 19 Cancelling the appliance operation
- 19 Fast Preheat
- 19 Notes
- 19 Activating the "Fast Preheat" function
- 19 1. Set a heating mode and temperature.
- 19 2. Touch the START l STOP touch button to start the heating mode.
- 19 3. Touch the FAST PREHEAT touch button to activate the function.
- 19 4. Once the set temperature has been reached, the "Fast Preheat" function switches itself off automatically. The ° symbol disappears from the display. Place the food in the oven cavity.
- 20 Panel Lock
- 20 Activating and Deactivating
- 20 1. Touch and hold the TIMERS touch button for approximately 4 seconds until "Panel Lock activated" is displayed. The lock is activated. The 1 symbol is displayed in the top left corner of the display.
- 20 2. Touch and hold the TIMERS touch button for approximately 4 seconds until "Panel Lock deactivated" is displayed.
- 20 Auto Convection Conversion
- 20 To turn on this feature:
- 20 1. Go to Settings
- 20 2. Press the ON|OFF touch button to turn the oven on.
- 20 3. Press the MENU touch button.
- 20 4. Scroll over to Settings on the touch screen.
- 20 5. Select Conv. Conversion and press ON.
- 20 6. Exit Settings and select “Save” to save your settings.
- 20 Meat Probe
- 20 Suitable Heating Modes
- 20 Notes
- 20 Inserting the Meat Probe into the Food
- 20 NOTICE:
- 21 Setting and Starting Appliance Operation
- 21 9 WARNING
- 21 Risk of burns
- 21 9 WARNING
- 21 Risk of electric shock
- 21 Notes
- 21 1. Insert the meat probe into the socket on the left-hand side of the oven cavity.
- 21 Note:
- 21 2. Close the appliance door.
- 21 NOTICE:
- 21 3. Touch the ON l OFF touch button.
- 21 4. Set the heating mode.
- 21 Note:
- 21 5. Touch the oven cavity temperature on the left in the bottom line.
- 21 6. Swipe to the left or right to select the required oven cavity temperature.
- 21 7. Touch the 8 symbol to apply the setting.
- 21 8. Touch the ¥ core temperature on the right in the bottom line.
- 21 9. Swipe to the left or right to select the required core temperature.
- 21 10. Touch the START l STOP touch button.
- 21 Changing or Stopping the Appliance Operation
- 21 1. Touch the oven cavity temperature or meat probe temperature.
- 21 2. Swipe to the left or right to change the temperature.
- 21 3. Touch the 8 symbol to apply the setting.
- 21 1. Use the ON l OFF touch button to switch off the appliance.
- 21 2. Using an oven glove, unplug the meat probe from the socket.
- 21 Core Temperatures of Different Foods
- 22 Sabbath Mode
- 22 Starting
- 22 1. Touch the ON l OFF touch button.
- 22 2. Swipe to the left or right to select "Sabbath ›".
- 22 3. Touch the temperature in the bottom line.
- 22 4. Swipe to the left or the right to select the required temperature.
- 22 5. Touch the 8 icon to apply the setting.
- 22 6. Touch the cooking time + in the bottom line.
- 22 7. Swipe to the left or the right to select the required duration.
- 22 8. Touch the 8 symbol to apply the setting.
- 22 9. Touch the START l STOP touch button.
- 22 Notes
- 22 Cancelling
- 22 Yom Tov Mode
- 22 Starting
- 22 1. Touch the ON l OFF touch button.
- 22 2. Swipe to the left or right to select "Yom Tov ›".
- 22 3. Touch the temperature in the bottom touch field.
- 22 4. Swipe to the left or the right to select the required temperature.
- 22 5. Touch the 8 icon to apply the setting.
- 22 6. Touch the cooking time + in the bottom touch field.
- 22 7. Swipe to the left or the right to select the required duration.
- 22 8. Touch the 8 icon to apply the setting.
- 22 9. Touch the START l STOP touch button.
- 22 Notes
- 22 Cancelling
- 23 Inserting Accessories
- 23 Note:
- 23 9 WARNING
- 23 Risk of Burns
- 23 9 CAUTION
- 23 NOTICE:
- 23 Note:
- 23 Example in the picture: Universal pan
- 23 Example in the picture: Rack
- 23 Stop Function
- 24 Steam Operation
- 24 9 WARNING
- 24 Risk of scalding
- 24 Noises
- 24 Steam Cooking
- 24 Note:
- 24 Setting
- 24 1. Refill water tank.
- 24 Note:
- 24 2. Touch the ON l OFF touch button.
- 24 3. Swipe to the left or right to select "Steam ‹".
- 24 4. Touch the temperature field.
- 24 5. Swipe to the left or the right to select the required temperature.
- 24 6. Touch the timer field +.
- 24 7. Swipe to the left or the right to select the required duration.
- 24 8. Touch the START l STOP touch button.
- 24 Cancelling
- 24 Note:
- 24 Exit
- 24 Steam Assisted Cooking
- 25 Steam Intensity
- 25 Suitable Heating Modes
- 25 Start
- 25 1. Refill water tank.
- 25 Note:
- 25 2. Touch the ON l OFF touch button.
- 25 3. Set the heating mode and temperature.
- 25 4. Touch the ADD STEAM touch button to switch on steam assistance.
- 25 5. On the display, swipe to the left or right to select the steam intensity.
- 25 6. Touch the 8 symbol to apply the setting.
- 25 7. Touch the START l STOP touch button.
- 25 Note:
- 25 Cancelling Steam Addition
- 25 1. Touch the ADD STEAM touch button to cancel the addition of steam early.
- 25 2. Touch the steam intensity in the bottom right corner of the display.
- 25 3. Swipe to the left or right to select "Off".
- 25 4. Touch the 8 symbol to apply the setting.
- 25 Note:
- 25 Cancelling
- 25 Note:
- 25 Exit
- 25 Proof
- 25 Note:
- 25 Start
- 25 1. Refill water tank.
- 25 Note:
- 25 2. Touch the ON l OFF touch button.
- 25 3. Swipe to the left or right to select "Proof".
- 25 4. Touch "1" in the bottom touch field.
- 25 5. Swipe to the left or right to select the required setting.
- 25 6. Touch the 8 symbol to apply the setting.
- 25 7. Touch "+" in the bottom touch field.
- 25 8. Swipe to the left or the right to select the required duration.
- 25 9. Touch the 8 symbol to apply the setting.
- 25 10. Touch the START l STOP touch button.
- 25 Cancelling
- 25 Note:
- 25 Exit
- 26 Defrost
- 26 Note:
- 26 Start
- 26 1. Refill water tank.
- 26 Note:
- 26 2. Touch the ON l OFF touch button.
- 26 3. Swipe to the left or right to select "Defrost “".
- 26 4. Touch the temperature in the bottom line.
- 26 5. Swipe to the left or the right to select the required temperature.
- 26 6. Touch the 8 icon to apply the setting.
- 26 7. Touch "+" in the bottom touch field.
- 26 8. Swipe to the left or the right to select the required duration.
- 26 9. Touch the 8 icon to apply the setting.
- 26 10. Touch the START l STOP touch button.
- 26 Cancelling
- 26 Note:
- 26 Exit
- 26 Reheating
- 26 Note:
- 26 Start
- 26 1. Refill water tank.
- 26 Note:
- 26 2. Touch the ON l OFF touch button.
- 26 3. Swipe to the left or right to select "Reheat ¨".
- 26 4. Touch the temperature in the bottom touch field.
- 26 5. Swipe to the left or the right to select the required temperature.
- 26 6. Touch the 8 icon to apply the setting.
- 26 7. Touch "+" in the bottom touch field.
- 26 8. Swipe to the left or the right to select the required duration.
- 26 9. Touch the 8 icon to apply the setting.
- 26 10. Touch the START l STOP touch button.
- 26 Cancelling
- 26 Note:
- 26 Exit
- 26 Refill Water Tank
- 26 9 WARNING
- 26 Risk of injury and fire
- 26 9 WARNING
- 26 Risk of Burns
- 27 NOTICE:
- 27 Notes
- 27 1. Open the appliance door.
- 27 2. Pull out the water tank from the right side of the oven cavity (figure !).
- 27 3. Fill the water tank with cold water up to the “max.” mark (figure ")
- 27 4. Fully close the tank cover until it locks.
- 27 5. Insert the filled water tank (figure #).
- 27 6. Ensure that the water tank has been pushed in all the way. The water tank should be level with the tank cavity (figure $).
- 27 7. Close the appliance door.
- 27 After Every Steam Operation
- 27 9 WARNING
- 27 Risk of scalding
- 27 9 WARNING
- 27 Risk of burns
- 27 NOTICE:
- 27 Notes
- 27 Empty Water Tank
- 27 NOTICE:
- 27 1. Open the appliance door.
- 27 2. Remove the water tank.
- 27 3. Empty the water tank, clean it with detergent and then rinse it thoroughly with clean water.
- 27 4. Dry all parts with a soft cloth.
- 27 5. Rub the seal on the cover until dry.
- 27 6. Leave to dry with the cover open.
- 27 7. Close the cover on the water tank and push it down.
- 27 8. Insert the water tank and close the appliance door.
- 28 Starting Drying
- 28 1. Let the appliance cool down.
- 28 2. Remove the worst of the food remnants from the oven cavity immediately and use a sponge to wipe away moisture from the oven cavity floor.
- 28 3. If necessary, touch the ON l OFF touch button to switch the appliance on.
- 28 4. Touch the MENU touch button to display the operating modes.
- 28 5. On the touch display, swipe to the left or right to select "Drying ª".
- 28 6. Touch the bottom touch field.
- 28 7. Touch the bottom touch field.
- 28 8. Touch the START l STOP touch button.
- 28 9. Open the appliance door and leave it open for 1 to 2 minutes so that the moisture in the oven cavity can escape.
- 28 Drying the Oven Cavity by Hand
- 28 1. Let the appliance cool down.
- 28 2. Remove any soil from the oven cavity.
- 28 3. Dry the oven cavity with a sponge.
- 28 4. Leave the appliance door open for 1 hour so that the oven cavity dries completely.
- 28 Steam Programs
- 28 9 WARNING
- 28 Risk of scalding
- 28 Information on the Settings
- 28 Selecting a Dish
- 29 Setting a Program
- 29 1. Touch the ON l OFF touch button to switch on the appliance.
- 29 2. Touch the MENU touch button.
- 29 3. Swipe to the left or right to select "Steam programs".
- 29 4. Touch the bottom line.
- 29 5. Touch the required category.
- 29 6. Swipe to the left or right to select the required steam program.
- 29 7. Touch the required steam program.
- 29 Note:
- 29 8. Some programs require a weight. Press the weight and scroll to adjust.
- 29 9. Touch the START l STOP touch button to start the appliance operation.
- 29 Note:
- 29 Continue cooking
- 29 1. Touch "Continue cooking".
- 29 2. If necessary, adjust the recommended setting or time amount.
- 29 3. Touch the START l STOP touch button to start "Continue cooking".
- 29 Cancelling
- 29 Note:
- 29 Exit
- 30 Home Connect
- 30 Notes
- 30 Setting Up
- 30 Connecting Your Oven to Home Connect
- 30 1. Install the Home Connect app.
- 30 2. Connect your oven to the Wi-Fi network.
- 30 3. Connect your oven to the app.
- 30 1. Install the Home Connect app.
- 30 2. Connect your oven to the Wi-Fi network.
- 30 Automatic Registration in the Home Network
- 30 Notes
- 30 1. Touch the MENU touch button.
- 30 2. Swipe to the left or right to select “Settings”.
- 30 3. Swipe to the left or right to select “Home Connect”.
- 30 4. Touch “Start assistant”.
- 30 5. Touch “Continue”.
- 30 6. Within 2 minutes press the WPS button on the router. Wait until “Network connection successful” is shown in the display.
- 31 7. The appliance is ready to connect to the app.
- 31 8. Follow the instructions of the app on your mobile device for automatic network registration.
- 31 Manual Registration in the Home Network
- 31 Note:
- 31 1. Touch the MENU touch button.
- 31 2. Swipe to the left or right to select "Settings".
- 31 3. Swipe to the left or right to select "Home Connect".
- 31 4. Touch “Start assistant”.
- 31 5. Touch “Continue”.
- 31 6. Touch "Connect manually".
- 31 7. Touch “Continue”.
- 31 8. Use the "HomeConnect" SSID and the "HomeConnect" key to register the mobile device on the oven network.
- 31 9. Wait until "Network connection successful" is shown on the display.
- 31 10. The appliance is ready to connect to the app.
- 31 11. Follow the instructions of the app on your mobile device for manual network registration.
- 32 Remote Start
- 32 Notes
- 32 1. Touch the MENU touch button.
- 32 2. Touch “Remote start”.
- 32 Home Connect Settings
- 32 Note:
- 32 Wi-Fi
- 32 1. Touch the MENU touch button.
- 32 2. Swipe to the left or right to select "Settings".
- 32 3. Swipe to the left or right to select "Home Connect".
- 32 4. Touch “Open settings”.
- 32 5. Swipe to the left or right to select "Wi-Fi".
- 32 6. Touch the bottom line to select “On” or “Off”.
- 32 7. Touch the ; field to return to the Home Connect settings menu.
- 32 Disconnecting from the Network
- 32 Note:
- 32 1. Touch the MENU touch button.
- 32 2. Swipe to the left or right to select "Settings".
- 32 3. Swipe to the left or right to select "Home Connect".
- 32 4. Touch “Open settings”.
- 32 5. Swipe to the left or right to select "Disconnect".
- 32 6. Touch “Disconnect from network”.
- 32 7. Confirm by touching “Disconnect”.
- 32 Note:
- 32 Connecting to the networkConnecting to the network
- 32 1. Touch the MENU touch button.
- 32 2. Swipe to the left or right to select "Settings".
- 32 3. Swipe to the left or right to select "Home Connect".
- 32 4. Touch “Open settings”.
- 32 5. Swipe to the left or right to select "Connect to network".
- 32 6. Touch “Start assistant”.
- 32 7. Follow the instructions in the section entitled “Manual registration in the home network” or “Automatic registration in the home network”.
- 32 Connect to App
- 32 Note:
- 32 1. Touch the MENU touch button.
- 32 2. Swipe to the left or right to select "Settings".
- 32 3. Swipe to the left or right to select "Home Connect".
- 32 4. Touch “Open settings”.
- 32 5. Swipe to the left or right to select "Connect to app".
- 32 6. Touch the bottom line to select “Start”.
- 33 Remote control
- 33 Notes
- 33 1. Touch the MENU touch button.
- 33 2. Swipe to the left or right to select "Settings".
- 33 3. Swipe to the left or right to select "Home Connect".
- 33 4. Touch “Open settings”.
- 33 5. Swipe to the left or right to select "Remote control".
- 33 6. Touch the bottom line to select “On” or “Off”.
- 33 7. Touch the ; field to return to the Home Connect settings menu.
- 33 Software Update
- 33 Notes
- 33 Information on Data Protection
- 33 Note:
- 34 Wi-Fi® Module
- 34 FCC COMPLIANCE STATEMENT
- 34 9 CAUTION
- 34 1. This device may not cause harmful interference, and
- 34 2. This device must accept any interference received, including interference that may cause undesired operation.
- 34 INDUSTRY CANADA STATEMENT
- 34 1. This device may not cause interference, and
- 34 2. This device must accept any interference, including interference that may cause undesired operation of the device.
- 34 Cleaning Your Oven
- 34 Suitable Cleaning Agents
- 34 NOTICE:
- 34 Tip:
- 34 9 WARNING
- 34 Risk of burns
- 34 Notes
- 35 Cleaning Guide
- 35 Notes
- 36 Surfaces in the Oven Cavity
- 36 Cleaning Enamel Surfaces
- 36 Note:
- 36 Keeping the Appliance Clean
- 36 Cleaning Functions
- 36 NOTICE:
- 36 Ecolytic Clean
- 36 Note:
- 36 Before Running the Ecolytic Clean Function
- 36 Cleaning the Oven Bottom and the Inside of the Appliance Door
- 36 NOTICE:
- 36 Start
- 36 1. Touch the ON l OFF touch button.
- 36 2. Touch the MENU touch button.
- 36 3. Swipe to the left or right to select "Ecolytic Clean ™".
- 36 4. Touch the bottom line.
- 36 5. Touch the bottom line.
- 36 6. Touch the START l STOP touch button.
- 37 Once the Cleaning Function has Ended
- 37 Note:
- 37 Easy Clean
- 37 9 WARNING
- 37 Risk of scalding
- 37 Setting
- 37 1. Remove the accessories and racks from the oven cavity.
- 37 2. Touch the ON l OFF touch button.
- 37 3. Touch the MENU touch button.
- 37 4. Swipe to the left or right to select "Easy Clean š".
- 37 5. Touch the bottom line.
- 37 6. Touch the START l STOP touch button.
- 37 Exit
- 37 Subsequent Cleaning
- 37 1. Open the appliance door and remove the remaining water with an absorbent sponge cloth.
- 37 2. Clean the smooth surfaces in the oven cavity with a dish cloth or a soft brush. Stubborn residues can be removed using a soft scouring pad.
- 37 3. Remove limescale with a cloth soaked in vinegar. Then wipe with clean water and rub dry with a soft cloth (including under the door seal).
- 37 4. Use the ON l OFF touch button to switch off the appliance.
- 37 5. Leave the appliance door ajar in the stop position (approx. 30°) for approx. one hour to allow the enamel surfaces in the oven cavity to dry thoroughly. Alternatively, you can also run the Drying function for the oven cavity.
- 37 Running the Drying Function for the Oven Cavity
- 37 1. Touch the ON l OFF touch button.
- 37 2. Touch the MENU touch button.
- 37 3. Swipe to the left or right to select "Drying ª".
- 37 4. Touch the bottom line.
- 37 5. Touch the START l STOP touch button.
- 37 Removing Heavy Food Deposits
- 38 Descale
- 38 Start
- 38 NOTICES
- 38 1. Touch the ON l OFF touch button.
- 38 2. Touch the MENU touch button.
- 38 3. Swipe to the left or right to select "Descale ,".
- 38 4. Touch continue.
- 38 5. Touch continue again.
- 38 6. Remove the water tank and fill it with descaling solution.
- 38 7. Mix 32 fluid oz. (950 ml) of water with 1/2 bottle (approximately 200 ml) of descale solution.
- 38 8. Once the water tank has been filled with descaling solution, push it back in again fully.
- 38 9. Follow the on-screen instructions.
- 38 First Rinsing Cycle
- 38 1. The display will prompt to open the appliance door. Remove the water tank and rinse thoroughly. Fill the tank with fresh water and reinsert.
- 38 2. Close the appliance door.
- 38 Second Rinsing Cycle
- 38 1. The display will prompt to open the appliance door. Remove the water tank and rinse throughly. Fill the tank with fresh water and reinsert.
- 38 2. Close the appliance door.
- 38 Completing Descale
- 38 1. Open the appliance door.
- 38 2. Empty water tank. Rinse thoroughly. Dry and reinsert.
- 38 3. Descaling is complete and the appliance is ready for use again.
- 39 Service
- 39 9 WARNING
- 39 Risk of electric shock
- 39 9 WARNING
- 39 Risk of electric shock
- 39 Troubleshooting Chart
- 42 STATEMENT OF LIMITED PRODUCT WARRANTY
- 42 What this Warranty Covers & Who it Applies to
- 42 How Long the Warranty Lasts
- 42 Repair/Replace as Your Exclusive Remedy
- 42 Out of Warranty Product
- 42 Warranty Exclusions
- 43 THERMADOR® Support
- 43 Service
- 43 Parts and Accessories
- 44 Table des MatièresNotice d’utilisation
- 45 Définitions de sécuritéDéfinitions de sécurité
- 45 9 AVERTISSEMENT
- 45 9 ATTENTION
- 45 AVIS :
- 45 Remarque :
- 46 IMPORTANTES CONSIGNES DE SÉCURITÉ
- 46 LIRE ET CONSERVER CES INSTRUCTIONS
- 46 AVERTISSEMENT
- 46 Installation et entretien corrects
- 46 AVERTISSEMENT
- 46 AVERTISSEMENT
- 46 Sécurité-incendie
- 46 AVERTISSEMENT
- 46 AVERTISSEMENT
- 47 AVERTISSEMENT
- 47 POUR RÉDUIRE LE RISQUE DE LÉSIONS CORPORELLES DANS L'ÉVENTUALITÉ D'UN FEU DE GRAISSE, OBSERVER LES CONSIGNES SUIVANTES :
- 47 a. ÉTOUFFER LES FLAMMES à l'aide d'un couvercle bien hermétique, d'une tôle à biscuits ou d'un plateau en métal, puis éteindre l'appareil. FAIRE ATTENTION À NE PAS SE BRÛLER. Si les flammes ne s'éteignent pas immédiatement, ÉVACUER LES LI...
- 47 b. NE JAMAIS SAISIR UN RÉCIPIENT QUI BRÛLE. Vous pourriez vous brûler.
- 47 c. NE PAS UTILISER D'EAU, y compris les chiffons ou serviettes mouillées. Une violente explosion de vapeur risque de se produire.
- 47 d. Utiliser un extincteur uniquement si :
- 47 Prévention des brûlures
- 47 ATTENTION
- 47 AVERTISSEMENT
- 47 Risques de brûlures
- 47 AVERTISSEMENT
- 47 Risque de brûlure
- 47 AVERTISSEMENT
- 47 Risque d'ébouillantement
- 48 AVERTISSEMENT
- 48 Risque de brûlure
- 48 AVERTISSEMENT
- 48 Risque de brûlures
- 48 Sécurité des enfants
- 48 AVERTISSEMENT
- 48 Consignes en matière de nettoyage
- 48 AVERTISSEMENT
- 48 Risque de blessure
- 48 AVERTISSEMENT
- 48 Risque de choc électrique
- 48 Sécurité pour la batterie de cuisine
- 48 AVERTISSEMENT
- 48 Risque de choc électrique
- 48 Avertissement issue de la proposition 65 de l’État de la Californie :
- 48 AVERTISSEMENT
- 49 Causes des dommages
- 49 AVIS
- 49 Protection de l'Environnement
- 49 Économie d’énergie
- 50 Accessoires
- 50 9 ATTENTION
- 50 Accessoires inclus
- 50 Remarque :
- 50 Accessoires spéciaux (non-inclus)
- 51 Familiarisation avec l'appareil
- 51 Remarque :
- 51 Vue d’ensemble du four
- 51 Cavité du four
- 51 9 ATTENTION
- 51 9 ATTENTION
- 51 Caractéristiques de la cavité du four
- 51 Évent de four
- 51 Ventilateur de refroidissement
- 51 Ventilateur à convection
- 51 Éclairage de four
- 51 Réservoir d’eau
- 52 Panneau de commande
- 52 Commandes
- 52 Touches tactiles
- 53 Écran tactile en couleur
- 53 Éléments de base de fonctionnement de l’écran :
- 53 Dans certains cas, on vous offre d’autres options de navigation dans le menu :
- 53 Menu principal
- 54 Menu Modes de cuisson
- 56 Avant la première utilisation
- 56 Avant la première utilisation
- 56 Dureté de l’eau
- 56 AVIS
- 56 Première mise en service
- 56 Réglage de l’heure du jour
- 56 1. Effleurez la ligne du bas.
- 56 2. Effleurez le champ tactile « Heure » et glissez vers la gauche ou la droite pour sélectionner l’heure actuelle.
- 56 3. Effleurez le champ tactile « Minute » et glissez vers la gauche ou la droite pour sélectionner les minutes actuelles.
- 56 4. Effleurez le symbole 8 pour confirmer les réglages.
- 57 Réglage de la langue
- 57 1. Effleurez la ligne du bas.
- 57 2. Glissez vers la gauche ou la droite pour sélectionner la langue requise.
- 57 3. Effleurez la ligne du haut.
- 57 Réglages de l’affichage de l’heure
- 57 1. Effleurez « Affichage de l’heure ».
- 57 2. Effleurez la ligne du bas.
- 57 3. Glissez vers la gauche ou la droite pour sélectionner « Numérique » ou « Analogue ».
- 57 4. Effleurez la ligne du haut.
- 57 Réglage de la dureté de l'eau
- 57 1. Effleurez « Dureté de l’eau ».
- 57 2. Effleurez la ligne du bas.
- 57 3. Glissez vers la gauche ou la droite pour sélectionner la bonne dureté de l’eau.
- 57 4. Effleurez la ligne du haut.
- 57 Réglage de Home Connect
- 57 1. Effleurez « Home Connect ».
- 57 2. Effleurez « Démarrer assistant ».
- 57 3. Respectez les directives du chapitre « Home Connect ».~ "Home Connect" à la page 73
- 57 Remarque :
- 57 Remarques
- 57 Étalonnage de l’appareil électroménager et nettoyage la cavité du four
- 57 Préparation de l’appareil électroménager pour étalonnage
- 57 1. Retirez les accessoires de la cavité du four.
- 57 2. Retirez toutes pièces restantes de l’emballage de la cavité du four notamment le granulé de polystyrène.
- 57 3. Avant d’étalonner l’appareil électroménager, essuyez les surfaces lisses de la cavité du four avec un chiffon doux et humide.
- 57 Remarques
- 57 AVIS :
- 57 1. Remplissez le réservoir d’eau.
- 57 2. Effleurez la touche tactile ON l OFF pour mettre l’appareil électroménager sous tension.
- 57 3. Le four s’étalonne automatiquement après un cycle en mode de chauffage vapeur à 212 °F (100 °C) pendant 30 minutes. Réglez le mode de cuisson, la température et la durée pour l’étalonnage. Effleurez START pour lancer la commande.
- 57 4. Après l’étalonnage, laissez l’appareil électroménager refroidir.
- 57 5. Séchez la sole de la cavité du four.
- 57 6. Réglez la cuisson à 475 °F (245 °C).
- 57 7. Maintenez la cuisine aérée lorsque l’appareil électroménager chauffe.
- 58 8. Éteignez l’appareil électroménager après la durée indiquée. Utilisez la touche tactile ON l OFF pour éteindre l’appareil électroménager.
- 58 9. Attendez le refroidissement de la cavité du four.
- 58 10. Nettoyez les surfaces lisses avec un torchon à vaisselle et de l’eau savonneuse.
- 58 11. Videz le réservoir d’eau et séchez la cavité du four.
- 58 Remarque :
- 58 Nettoyer les accessoires
- 58 Réglages de base
- 58 Modification des paramètres
- 58 1. Effleurez la touche tactile ON l OFF (Marche l Arrêt).
- 58 2. Effleurez la touche tactile MENU.
- 58 3. Glissez vers la gauche ou la droite pour sélectionner « Paramètres 4 ».
- 58 4. Effleurez « Continuer ».
- 58 5. Glissez vers la gauche ou la droite pour sélectionner le réglage désiré.
- 58 6. Effleurez le champ tactile inférieur.
- 58 7. Glissez vers la gauche ou la droite pour sélectionner le réglage désiré.
- 58 8. Effleurez l’icône 8 (le cas échéant) pour activer le réglage.
- 58 9. Effleurez la touche tactile MENU.
- 58 10. Effleurez « Sauvegarder » pour conserver les modifications.
- 58 Réglages Offerts
- 59 Généralités sur le fonctionnement
- 59 Cuisson à haute altitude
- 59 Mise sous tension ou hors tension de l'appareil
- 59 Remarques
- 59 Options de minuterie
- 59 Affichage et dissimulation des options de minuterie
- 59 Remarque :
- 59 Minuterie du four
- 59 1. Effleurez la touche tactile ON l OFF.
- 59 2. Réglez le mode de cuisson et la température.
- 59 3. Effleurez la touche tactile TIMERS.
- 59 4. Effleurez le champ tactile « + Minuterie de four ».
- 59 5. Effleurez le champ requis et glissez vers la gauche ou la droite pour régler la minuterie de four.
- 59 6. Effleurez le symbole 8.
- 59 7. Effleurez la touche tactile START l STOP.
- 59 Remarque :
- 60 Minuterie de cuisine
- 60 1. Effleurez la touche tactile TIMERS.
- 60 2. Glissez vers la gauche ou la droite pour sélectionner la valeur de la minuterie. Vous pouvez régler les heures, les minutes et les secondes.
- 60 3. Effleurez l’icône 8.
- 60 Remarque :
- 60 Opération reportée - « Heure de fin »
- 60 Remarques
- 60 9 ATTENTION
- 60 1. Placez les aliments dans le bon accessoire et glissez- le dans la cavité du four. Fermez la porte de l’appareil électroménager.
- 60 2. Effleurez la touche tactile ON l OFF.
- 60 3. Réglez le mode de cuisson.
- 60 4. Effleurez la touche tactile TIMERS. Les options de minuterie s’affichent à l’écran.
- 60 5. Sélectionnez la minuterie du four et réglez un temps de cuisson. Effleurez l’icône 8.
- 60 6. Sélectionnez de nouveau les TIMERS et réglez l’heure de fin de cuisson. Effleurez l’icône 8.
- 60 7. Effleurez la touche tactile START l STOP.
- 60 Vérification, modification ou annulation des réglages
- 60 1. Effleurez la touche tactile TIMERS.
- 60 2. Effleurez l’option de minuterie requise.
- 60 3. Glisser vers la gauche ou la droite sur l’écran tactile pour modifier les réglages.
- 60 Réglage d’un mode de cuisson
- 60 1. Effleurez la touche tactile ON l OFF pour mettre l’appareil électroménager sous tension.
- 60 2. Glissez vers la gauche sur la ligne supérieure de l’écran pour sélectionner « Convection réelle » ‚.
- 61 3. Glissez vers la gauche ou la droite sur la ligne inférieure de l’écran pour sélectionner la température.
- 61 4. Effleurez la touche tactile START l STOP pour lancer la commande.
- 61 Valeurs par défaut
- 61 Barre de préchauffage
- 61 Touche Tactile INFO
- 61 Sons
- 61 Modification ou annulation du fonctionnement de l’appareil électroménager
- 61 Remarque :
- 61 Modification du fonctionnement de l’appareil électroménager
- 61 1. Effleurez la touche tactile START l STOP pour interrompre la cuisson.
- 61 2. Effleurez la zone de l’écran du réglage à modifier.
- 61 3. Glissez vers la gauche ou la droite pour modifier le réglage.
- 61 4. Effleurez la touche tactile START l STOP pour lancer le changement de commande.
- 61 Remarques
- 61 Annulation de la commande de l’appareil électroménager
- 61 Préchauffage rapide
- 61 Remarques
- 62 Activation de la fonction « Préchauffage rapide »
- 62 1. Réglez un mode de cuisson et la température.
- 62 2. Effleurez la touche tactile START l STOP pour lancer le mode de cuisson.
- 62 3. Effleurez la touche tactile FAST PREHEAT pour activer la fonction.
- 62 4. Une fois la température réglée atteinte, la fonction « Préchauffage rapide » s’éteint automatiquement. Le symbole ° disparaît de l’écran. Placez les aliments dans la cavité du four.
- 62 Verrouillage du Panneau de Commande
- 62 Activation et désactivation
- 62 1. Appuyer et maintenez la touche tactile TIMERS enfoncée pendant près de quatre secondes jusqu’à ce que « Verrouillage du panneau activé » s’affiche. Le verrouillage du panneau est activé. Le symbole 1 est affiché dans le coin supérieur...
- 62 2. Appuyer et maintenez la touche tactile TIMERS enfoncée pendant près de quatre secondes jusqu’à ce que « Verrouillage du panneau désactivé » s’affiche.
- 62 Conversion Convection Auto
- 62 Pour activer cette fonction :
- 62 1. Passez à Réglages
- 62 2. Effleurez la touche tactile MARCHE l ARRÊT (ON l OFF) pour mettre le four sous tension.
- 62 3. Effleurez la touche tactile MENU.
- 62 4. Défilez vers Réglages sur l’écran tactile.
- 62 5. Sélectionnez Conversion convection et effleurez MARCHE (ON).
- 62 6. Quittez les réglages et sélectionnez « Enregistrer » pour les conserver.
- 62 Sonde à viande
- 62 Modes de cuisson convenables
- 62 Remarques
- 62 Insertion de la sonde thermométrique dans les aliments
- 63 AVIS :
- 63 Démarrer et arrêter l'appareil
- 63 9 AVERTISSEMENT
- 63 Risque de brûlures
- 63 9 AVERTISSEMENT
- 63 Risque de choc électrique
- 63 Remarques
- 63 1. Insérez la sonde thermométrique dans la douille du côté gauche de la cavité du four.
- 63 Remarque :
- 63 2. Fermez la porte de l’appareil électroménager.
- 63 AVIS :
- 63 3. Effleurez la touche tactile ON l OFF.
- 63 4. Réglez le mode de cuisson.
- 63 Remarque :
- 63 5. Effleurez la température de la cavité du four à gauche sur la ligne inférieure.
- 63 6. Glissez vers la gauche ou la droite pour sélectionner la température requise pour la cavité du four.
- 63 7. Effleurez le symbole 8 pour activer le réglage.
- 63 8. Effleurez la température interne ¥ à droite sur la ligne inférieure.
- 63 9. Glissez vers la gauche ou la droite pour sélectionner la température interne requise.
- 63 10. Effleurez la touche tactile START l STOP.
- 63 Modification ou arrêt du fonctionnement de l’appareil
- 63 1. Effleurez la température de la cavité du four ou la température interne.
- 63 2. Glissez vers la gauche ou la droite pour modifier la température.
- 63 3. Effleurez le symbole 8 pour activer le réglage.
- 63 1. Utilisez la touche tactile ON l OFF pour éteindre l’appareil électroménager.
- 63 2. Portez un gant de four pour débrancher la sonde thermométrique de la douille.
- 64 Températures internes de différents aliments
- 64 Mode Sabbat
- 64 Démarrage
- 64 1. Effleurez la touche tactile ON l OFF.
- 64 2. Glissez vers la gauche ou la droite pour sélectionner « Sabbat › ».
- 64 3. Effleurez la température sur la ligne inférieure.
- 64 4. Glissez vers la gauche ou la droite pour sélectionner la température requise.
- 64 5. Effleurez l’icône 8 pour activer le réglage.
- 64 6. Effleurez le temps de cuisson + sur la ligne du bas.
- 64 7. Glissez vers la gauche ou la droite pour sélectionner la durée requise.
- 64 8. Effleurez le symbole 8 pour activer le réglage.
- 64 9. Effleurez la touche tactile START l STOP.
- 64 Remarques
- 64 Annulation
- 64 Mode Yom Tov
- 64 Démarrage
- 64 1. Effleurez la touche tactile ON l OFF.
- 64 2. Glissez vers la gauche ou la droite pour sélectionner « Yom Tov › ».
- 64 3. Effleurez la température dans le champ tactile inférieur.
- 64 4. Glissez vers la gauche ou la droite pour sélectionner la température requise.
- 64 5. Effleurez l’icône 8 pour activer le réglage.
- 64 6. Effleurez le temps de cuisson + dans le champ tactile inférieur.
- 64 7. Glissez vers la gauche ou la droite pour sélectionner la durée requise.
- 64 8. Effleurez l’icône 8 pour activer le réglage.
- 64 9. Effleurez la touche tactile START l STOP.
- 64 Remarques
- 65 Annulation
- 65 Insertion des accessoires
- 65 Remarque :
- 65 9 AVERTISSEMENT
- 65 Risque de brûlures
- 65 9 ATTENTION
- 65 AVIS :
- 65 Remarque :
- 65 Exemple sur la photo : poêle universelle
- 65 Exemple sur la photo : grille
- 66 Système de butée
- 66 Commande de vapeur
- 66 9 AVERTISSEMENT
- 66 Risque de brûlures
- 66 Bruits
- 66 Cuisson à la vapeur
- 66 Remarque :
- 66 Réglage
- 66 1. Remplissez le réservoir d’eau.
- 66 Remarque :
- 66 2. Effleurez la touche tactile ON l OFF.
- 66 3. Glissez vers la gauche ou la droite pour sélectionner « Vapeur ‹ ».
- 66 4. Effleurez le champ tactile de la température.
- 66 5. Glissez vers la gauche ou la droite pour sélectionner la température requise.
- 66 6. Effleurez le champ + de la minuterie.
- 67 7. Glissez vers la gauche ou la droite pour sélectionner la durée requise.
- 67 8. Effleurez la touche tactile START l STOP.
- 67 Annulation
- 67 Remarque :
- 67 Quitter
- 67 Cuisson à l’aide de vapeur
- 67 Intensité de la vapeur
- 67 Modes de cuisson convenables
- 67 Démarrer
- 67 1. Remplissez le réservoir d’eau.
- 67 Remarque :
- 67 2. Effleurez la touche tactile ON l OFF.
- 67 3. Réglez le mode de cuisson et la température.
- 67 4. Effleurez la touche tactile ADD STEAM pour utiliser la vapeur.
- 67 5. À l’écran, glissez vers la gauche ou la droite pour sélectionner l’intensité de la vapeur.
- 67 6. Effleurez le symbole 8 pour activer le réglage.
- 67 7. Effleurez la touche tactile START l STOP.
- 67 Remarque :
- 67 Annulation de l’ajout de vapeur
- 67 1. Effleurez la touche tactile ADD STEAM pour annuler l’ajout de vapeur tôt dans le processus.
- 67 2. Effleurez l’intensité de la vapeur dans le coin inférieur droit de l’écran.
- 67 3. Glissez vers la gauche ou la droite pour sélectionner « Arrêt » (Off).
- 67 4. Effleurez le symbole 8 pour activer le réglage.
- 67 Remarque :
- 67 Annulation
- 67 Remarque :
- 67 Quitter
- 68 Levée de Pâte
- 68 Remarque :
- 68 Démarrer
- 68 1. Remplissez le réservoir d’eau.
- 68 Remarque :
- 68 2. Effleurez la touche tactile ON l OFF.
- 68 3. Glissez vers la gauche ou la droite pour sélectionner « Levée de pâte ».
- 68 4. Effleurez « 1 » dans le champ tactile inférieur.
- 68 5. Glissez vers la gauche ou la droite pour sélectionner le réglage requis.
- 68 6. Effleurez le symbole 8 pour activer le réglage.
- 68 7. Effleurez « + » dans le champ tactile inférieur.
- 68 8. Glissez vers la gauche ou la droite pour sélectionner la durée requise.
- 68 9. Effleurez le symbole 8 pour activer le réglage.
- 68 10. Effleurez la touche tactile START l STOP.
- 68 Annulation
- 68 Remarque :
- 68 Quitter
- 68 Décongeler
- 68 Remarque :
- 68 Démarrer
- 68 1. Remplissez le réservoir d’eau.
- 68 Remarque :
- 68 2. Effleurez la touche tactile ON l OFF.
- 68 3. Glissez vers la gauche ou la droite pour sélectionner « Décongeler “ ».
- 68 4. Effleurez la température sur la ligne inférieure.
- 68 5. Glissez vers la gauche ou la droite pour sélectionner la température requise.
- 68 6. Effleurez l’icône 8 pour activer le réglage.
- 68 7. Effleurez « + » dans le champ tactile inférieur.
- 68 8. Glissez vers la gauche ou la droite pour sélectionner la durée requise.
- 68 9. Effleurez l’icône 8 pour activer le réglage.
- 68 10. Effleurez la touche tactile START l STOP.
- 68 Annulation
- 68 Remarque :
- 68 Quitter
- 69 Réchauffage
- 69 Remarque :
- 69 Démarrer
- 69 1. Remplissez le réservoir d’eau.
- 69 Remarque :
- 69 2. Effleurez la touche tactile ON l OFF.
- 69 3. Glissez vers la gauche ou la droite pour sélectionner « Réchauffer ¨ ».
- 69 4. Effleurez la température dans le champ tactile inférieur.
- 69 5. Glissez vers la gauche ou la droite pour sélectionner la température requise.
- 69 6. Effleurez l’icône 8 pour activer le réglage.
- 69 7. Effleurez « + » dans le champ tactile inférieur.
- 69 8. Glissez vers la gauche ou la droite pour sélectionner la durée requise.
- 69 9. Effleurez l’icône 8 pour activer le réglage.
- 69 10. Effleurez la touche tactile START l STOP.
- 69 Annulation
- 69 Remarque :
- 69 Quitter
- 69 Remplissage du réservoir d’eau
- 69 9 AVERTISSEMENT
- 69 Risque de blessures et d’incendie
- 69 9 AVERTISSEMENT
- 69 Risque de brûlures
- 69 AVIS :
- 69 Remarques
- 70 1. Ouvrez la porte de l’appareil électroménager.
- 70 2. Retirez le réservoir d’eau du côté droit de la cavité du four (figure !).
- 70 3. Remplissez le réservoir d’eau avec de l’eau froide jusqu’à la marque « max » (figure ").
- 70 4. Fermez bien le couvercle du réservoir jusqu’à ce qu’il se verrouille.
- 70 5. Insérez le réservoir d’eau remplie (figure #).
- 70 6. Assurez-vous que le réservoir est entièrement enfoncé dans sa niche. Il doit être de niveau avec la cavité du réservoir (figure $).
- 70 7. Fermez la porte de l’appareil électroménager.
- 70 Après chaque utilisation de la vapeur
- 70 9 AVERTISSEMENT
- 70 Risque de brûlures
- 70 9 AVERTISSEMENT
- 70 Risque de brûlures
- 70 AVIS :
- 70 Remarques
- 70 Vidange du réservoir d’eau
- 70 AVIS :
- 70 1. Ouvrez la porte de l’appareil électroménager.
- 70 2. Retirez le réservoir d’eau.
- 70 3. Videz-le, nettoyez le réservoir d’eau avec du détergent puis rincez-le à fond à l’eau propre.
- 70 4. Séchez toutes les pièces avec un chiffon doux.
- 70 5. Frottez le joint du couvercle jusqu’à ce qu’il soit sec.
- 70 6. Laissez sécher le réservoir avec le couvercle ouvert.
- 70 7. Fermez le couvercle du réservoir d’eau et enfoncez-le.
- 70 8. Insérez le réservoir d’eau et fermez la porte de l’appareil électroménager.
- 70 Lancement du séchage
- 70 1. Laissez l’appareil électroménager refroidir.
- 70 2. Délogez les plus gros morceaux de restants d’aliments de la cavité du four immédiatement et utilisez une éponge pour essuyer toute trace d’humidité de la sole.
- 70 3. Au besoin, effleurez la touche tactile ON l OFF pour mettre l’appareil électroménager sous tension.
- 70 4. Effleurez la touche tactile MENU pour afficher les modes de fonctionnement.
- 70 5. À l’écran tactile, glissez vers la gauche ou la droite pour sélectionner « Séchage ª ».
- 70 6. Effleurez le champ tactile inférieur.
- 70 7. Effleurez le champ tactile inférieur.
- 70 8. Effleurez la touche tactile START l STOP.
- 70 9. Ouvrez la porte de l’appareil électroménager. Laissez- la ouverte entre une et deux minutes pour laisser l’humidité s’échapper de la cavité du four.
- 71 Séchage manuel de la cavité du four
- 71 1. Laissez l’appareil électroménager refroidir.
- 71 2. Retirez toute salissure de la cavité du four.
- 71 3. Séchez la cavité du four avec une éponge.
- 71 4. Laissez la porte de l’appareil électroménager ouverte pendant une heure pour sécher complètement la cavité du four.
- 71 Programmes à vapeur
- 71 9 AVERTISSEMENT
- 71 Risque d'ébouillantement
- 71 Renseignements à propos des réglages
- 71 Sélection d’un plat
- 72 Réglage d’un programme
- 72 1. Effleurez la touche tactile ON l OFF pour mettre l’appareil électroménager sous tension.
- 72 2. Effleurez la touche tactile MENU.
- 72 3. Glissez vers la gauche ou la droite pour sélectionner « Programmes vapeur ».
- 72 4. Effleurez la ligne du bas.
- 72 5. Effleurez la catégorie requise.
- 72 6. Glissez vers la gauche ou la droite pour sélectionner le programme de cuisson à la vapeur requis.
- 72 7. Effleurez le programme vapeur requis.
- 72 Remarque :
- 72 8. Certains programmes demandent le poids de l’aliment. Appuyez sur Poids et faites défiler pour le régler.
- 72 9. Effleurez la touche tactile START l STOP pour lancer la commande.
- 72 Remarque :
- 72 Poursuite de la cuisson
- 72 1. Effleurez « Poursuivre la cuisson ».
- 72 2. Au besoin, réglez l’appareil à la durée ou au réglage recommandé.
- 72 3. Effleurez la touche tactile START l STOP pour lancer la commande « Poursuive la cuisson ».
- 72 Annulation
- 72 Remarque :
- 72 Quitter
- 73 Home Connect
- 73 Remarques
- 73 Configuration
- 73 Connexion du four à Home Connect
- 73 1. Installez l’appli Home Connect.
- 73 2. Connectez le four au réseau Wi-Fi.
- 73 3. Connectez le four à l’appli.
- 73 1. Installez l’appli Home Connect.
- 73 2. Connectez le four au réseau Wi-Fi.
- 73 Connexion automatique au réseau domestique
- 73 Remarques
- 73 1. Effleurez la touche tactile MENU.
- 73 2. Glissez vers la gauche ou la droite pour sélectionner « Réglages ».
- 73 3. Glissez vers la gauche ou la droite pour sélectionner « Home Connect ».
- 73 4. Effleurez « Démarrer assistant ».
- 74 5. Effleurez « Continuer ».
- 74 6. Dans les deux minutes, appuyez sur le bouton WPS du routeur. Attendez que « Connexion réseau réussie » s’affiche à l’écran.
- 74 7. L’appareil électroménager est prêt à se connecter à l’appli.
- 74 8. Respectez les directives de l’appli sur l’appareil mobile pour une inscription automatique au réseau.
- 74 Connexion manuelle au réseau domestique
- 74 Remarque :
- 74 1. Effleurez la touche tactile MENU.
- 74 2. Faites défiler vers la gauche ou la droite pour sélectionner « Réglages ».
- 74 3. Faites défiler vers la gauche ou la droite pour sélectionner « Home Connect ».
- 74 4. Effleurez « Démarrer assistant ».
- 74 5. Effleurez « Continuer ».
- 74 6. Effleurez « Connexion manuelle ».
- 74 7. Effleurez « Continuer ».
- 74 8. Utilisez le SSID « HomeConnect » et la clé « HomeConnect » pour enregistrer l’appareil mobile au réseau du four.
- 75 9. Attendez que « Connexion réseau réussie » s’affiche à l’écran.
- 75 10. L’appareil électroménager est prêt à se connecter à l’appli.
- 75 11. Respectez les directives de l’appli sur l’appareil mobile pour une inscription manuelle au réseau.
- 75 Démarrage à distance
- 75 Remarques
- 75 1. Effleurez la touche tactile MENU.
- 75 2. Effleurez « Démarrage à distance ».
- 75 Réglages Home Connect
- 75 Remarque :
- 75 WiFi
- 75 1. Effleurez la touche tactile MENU.
- 75 2. Glissez vers la gauche ou la droite pour sélectionner « Réglages ».
- 75 3. Glissez vers la gauche ou la droite pour sélectionner « Home Connect ».
- 75 4. Effleurez « Ouvrir réglages ».
- 75 5. Glissez vers la gauche ou la droite pour sélectionner « Wi-Fi ».
- 75 6. Effleurez la ligne du bas pour sélectionner « Activé » ou « Désactivé ».
- 75 7. Effleurez le champ ; pour revenir au menu de réglages de Home Connect.
- 75 Se déconnecter du réseauSe déconnecter du réseau
- 75 Remarque :
- 75 1. Effleurez la touche tactile MENU.
- 75 2. Glissez vers la gauche ou la droite pour sélectionner « Réglages ».
- 75 3. Glissez vers la gauche ou la droite pour sélectionner « Home Connect ».
- 75 4. Effleurez « Ouvrir réglages ».
- 75 5. Glissez vers la gauche ou la droite pour sélectionner « Déconnexion ».
- 76 6. Effleurez « Déconnexion du réseau ».
- 76 7. Confirmez le choix en effleurant « Déconnexion ».
- 76 Remarque :
- 76 Se connecter au réseauSe connecter au réseau
- 76 1. Effleurez la touche tactile MENU.
- 76 2. Glissez vers la gauche ou la droite pour sélectionner « Réglages ».
- 76 3. Glissez vers la gauche ou la droite pour sélectionner « Home Connect ».
- 76 4. Effleurez « Ouvrir réglages ».
- 76 5. Glissez vers la gauche ou la droite pour sélectionner « Connexion au réseau ».
- 76 6. Effleurez « Démarrer assistant ».
- 76 7. Respectez les directives de la section intitulée « Inscription manuelle au réseau domestique » ou « Inscription automatique au réseau domestique ».
- 76 Connexion avec l'appli
- 76 Remarque :
- 76 1. Effleurez la touche tactile MENU.
- 76 2. Glissez vers la gauche ou la droite pour sélectionner « Réglages ».
- 76 3. Glissez vers la gauche ou la droite pour sélectionner « Home Connect ».
- 76 4. Effleurez « Ouvrir réglages ».
- 76 5. Glissez vers la gauche ou la droite pour sélectionner « Connexion à l’appli ».
- 76 6. Effleurez la ligne du bas pour sélectionner « Démarrer ».
- 76 Télécommande
- 76 Remarques
- 76 1. Effleurez la touche tactile MENU.
- 76 2. Glissez vers la gauche ou la droite pour sélectionner « Réglages ».
- 76 3. Glissez vers la gauche ou la droite pour sélectionner « Home Connect ».
- 76 4. Effleurez « Ouvrir réglages ».
- 76 5. Glissez vers la gauche ou la droite pour sélectionner « Télécommande ».
- 76 6. Effleurez la ligne du bas pour sélectionner « Activée » ou « Désactivée ».
- 76 7. Effleurez le champ ; pour revenir au menu de réglages de Home Connect.
- 76 Mise à jour du logiciel
- 77 Remarques
- 77 Remarque liée à la protection des données
- 77 Remarque :
- 77 Module Wi-FiMD
- 77 DÉCLARATION DE CONFORMITÉ DE LA FCC
- 77 9 ATTENTION
- 77 1. cet appareil ne peut causer d’interférences nuisibles; et
- 77 2. cet appareil doit accepter toute interférence reçue, notamment celle pouvant entraîner un dysfonctionnement.
- 77 AVIS D’INDUSTRIE CANADA
- 77 1. L'appareil ne doit pas produire de brouillage, et
- 77 2. L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
- 78 Nettoyage du four
- 78 Produits de nettoyage appropriés
- 78 AVIS :
- 78 Conseil :
- 78 9 AVERTISSEMENT
- 78 Risque de brûlures
- 78 Remarques
- 78 Guide de nettoyage
- 79 Remarques
- 79 Surfaces de la cavité du four
- 79 Nettoyage de surfaces émaillées
- 79 Remarque :
- 80 Nettoyage de l’appareil électroménager
- 80 Fonctions de nettoyage
- 80 AVIS :
- 80 Nettoyage Écolyse
- 80 Remarque :
- 80 Avant le nettoyage par écolyse
- 80 Nettoyage de la sole du four et de la partie interne de la porte de l’appareil électroménager
- 80 AVIS :
- 80 Démarrer
- 80 1. Effleurez la touche tactile ON l OFF.
- 80 2. Effleurez la touche tactile MENU.
- 80 3. Glissez vers la gauche ou la droite pour sélectionner « Nettoyage par écolyse ™ ».
- 80 4. Effleurez la ligne du bas.
- 80 5. Effleurez la ligne du bas.
- 80 6. Effleurez la touche tactile START l STOP.
- 81 À la fin de la fonction Nettoyage
- 81 Remarque :
- 81 Nettoyage facile
- 81 9 AVERTISSEMENT
- 81 Risque de brûlures
- 81 Réglage
- 81 1. Retirez les accessoires et les grilles de la cavité du four.
- 81 2. Effleurez la touche tactile MARCHE l ARRÊT (ON l OFF).
- 81 3. Effleurez la touche tactile MENU.
- 81 4. Glissez vers la gauche ou la droite pour sélectionner « Nettoyage facile š ».
- 81 5. Effleurez la ligne du bas.
- 81 6. Effleurez la touche tactile DÉMARRAGE l ARRÊT (START l STOP).
- 81 Quitter
- 81 Nettoyage subséquent
- 81 1. Ouvrez la porte de l’appareil électroménager et retirez l’eau restante avec un chiffon absorbant.
- 81 2. Nettoyez les surfaces lisses de la cavité du four avec un torchon à vaisselle ou une brosse à soies douces. Les résidus tenaces peuvent être éliminés avec un tampon à récurer doux.
- 81 3. Éliminez le tartre avec un chiffon humecté de vinaigre. Puis rincez à l’eau propre et essuyez avec un chiffon doux (y compris sous le joint de la porte).
- 81 4. Utilisez la touche tactile ON l OFF pour éteindre l’appareil électroménager.
- 81 5. Laissez la porte de l’appareil électroménager entrouverte à la position d’arrêt (environ 30 degrés), pendant environ une heure pour permettre aux surfaces émaillées de la cavité du four de bien sécher. Sinon, vous pouvez également la...
- 81 Exécution de la fonction de séchage de la cavité du four
- 81 1. Effleurez la touche tactile MARCHE l ARRÊT (ON l OFF).
- 81 2. Effleurez la touche tactile MENU.
- 81 3. Glissez vers la gauche ou la droite pour sélectionner « Séchage ª ».
- 81 4. Effleurez la ligne du bas.
- 81 5. Effleurez la touche tactile DÉMARRAGE l ARRÊT (START l STOP).
- 81 Élimination des dépôts alimentaires importants
- 82 Détartrage
- 82 Démarrer
- 82 AVIS
- 82 1. Effleurez la touche tactile MARCHE l ARRÊT (ON l OFF).
- 82 2. Effleurez la touche tactile MENU.
- 82 3. Faites défiler vers la gauche ou la droite pour sélectionner « Détratrer , ».
- 82 4. Effleurez « Continuer ».
- 82 5. Effleurez de nouveau « Continuer ».
- 82 6. Retirez le réservoir d’eau et remplissez-le avec la solution de détartrage.
- 82 7. Mélangez 32 oz liquides (950 ml) d’eau avec une demi-bouteille de solution de détartrage (près de 200 ml).
- 82 8. Une fois le réservoir rempli de solution de détartrage, réinsérez-le complètement.
- 82 9. Respectez les directives à l’écran.
- 82 Premier cycle de rinçage
- 82 1. Un message apparaît à l’écran vous demandant d’ouvrir la porte de l’appareil électroménager. Retirez le réservoir d’eau et rincez-le complètement. Remplissez-le d’eau fraîche puis réinsérez le réservoir.
- 82 2. Fermez la porte de l’appareil électroménager.
- 82 Deuxième cycle de rinçage
- 82 1. Un message apparaît à l’écran vous demandant d’ouvrir la porte de l’appareil électroménager. Retirez le réservoir d’eau et rincez-le complètement. Remplissez-le d’eau fraîche puis réinsérez le réservoir.
- 82 2. Fermez la porte de l’appareil électroménager.
- 82 Finalisation du détartrage
- 82 1. Ouvrez la porte de l’appareil électroménager.
- 82 2. Videz le réservoir d’eau, rincez complètement, séchez et réinsérez le réservoir.
- 82 3. Le détartrage est terminé et l’appareil électroménager est de nouveau prêt à être utilisé.
- 83 Dépannage
- 83 9 AVERTISSEMENT
- 83 Risque de choc électrique
- 83 9 AVERTISSEMENT
- 83 Risque de choc électrique
- 83 Tableau de dépannage
- 86 DÉCLARATION DE GARANTIE LIMITÉE DU PRODUIT
- 86 Couverture de la garantie limitée
- 86 Durée de la garantie
- 86 Réparation ou remplacement : votre recours exclusif
- 86 Produit hors garantie
- 87 Exclusions de garantie
- 88 Soutien THERMADOR®
- 88 Dépannage
- 88 Pièces et accessoires