steam press instruction manual

Add to My manuals
18 Pages

advertisement

steam press instruction manual | Manualzz

TROUBLE SHOOTING THE STEAM PRESS

Below is a chart detailing the most common problems, their causes and solutions. Before shipping any appliance to a service

center please check to make sure that the solution is not listed here:

PROBLEM

Steam Press Cannot Be Opened

Using Pressing Handle.

CAUSE

Locking Knob is in Locked Position

SOLUTION

Turn the Locking Knob to the Unlocked

Position

Steam Press Becomes Warm but DOES NOT Remove Wrinkles

Temperature Setting is not high enough for the fabric attempted.

Temperature has not been selected.

Gradually increase the temperature until obtaining the desired results.

Turn the Temperature Control Dial to an appropriate setting.

Press DOES NOT get warm

Press is not plugged into an outlet.

Plug the appliance in.

Automatic Shut-Off has engaged. The

Pressing Plate has been lowered for more the 15 seconds without being raised.

Automatic Shut-Off has engaged. The

Pressing Plate has been raised for more than 15 minutes without use.

Push the ON/OFF switch to the OFF position and back to ON. Raise the

Pressing Plate during the warm-up period.

Push the ON/OFF switch to the OFF position and back to ON. Raise or lower the Pressing Plate to restart the heater.

Steam Press Instruction Manual

Page 15

PROBLEM

No Steam.

CAUSE

Water level is too low.

Controls have not been properly set.

The Steam Press is in the open position.

Water drips from the Pressing Plate.

Temperature Control Dial has not been set properly.

The Pressing Plate has not reached the steam temperature setting.

SOLUTION

Fill the water Tank.

Turn the Temperature Control Dial clockwise to a higher temperature. Wait for the

Steam Ready light to come on.

Close the Steam Press to use the control.

Turn the Temperature Control Dial clockwise to a higher temperature.

Wait for the Ready Light.

The Pressing Handle will not move into the Automatic Maximum pressure position.

Item on the Ironing Board is too thick to use this pressure.

Page 16

Use lighter pressure on thicker items.Use

added steam for wrinkles.

Steam Press Instruction Manual

Disposal of old Electrical & Electronic Equipment (Applicable in the European Union and other

European countries with separate collection systems).

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources.

For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

advertisement

Key Features

  • Large pressing surface
  • Multiple dry and steam settings
  • Burst setting to remove stubborn wrinkles
  • Variable temperature control
  • Automatic shut-off safety feature
  • Automatic wake-up feature
  • Power indicator light
  • Over 100 Lbs. of even pressure
  • Protects delicate fabrics

Related manuals

Frequently Answers and Questions

How do I fill the water tank?
Always unplug the appliance BEFORE filling the tank. Fill the water tank with the Pressing Plate lifted to the raised (up) position. Slide the Water Tank towards the front of the unit. Using the Water Container, slowly pour the water into the Water Tank Fill Holes.
How do I use the steam burst feature?
The Steam Burst function can only be used when the Steam Ready Light is on AND the steam press is in an opened position. Do not use the Steam Burst function when the steam press is closed, or you may damage the unit.
What do I do if the automatic shut-off feature engages?
Push the ON/OFF switch to the OFF position and back to ON. Raise or lower the Pressing Plate to restart the heater.
How do I clean the pressing plate?
Place the Pressing Cushion in the center of the Ironing Board. Place a clean towel over the Pressing Cushion and the Ironing Board. Set the Steam, Control and Temperature Control to their maximum setting. Gently lower the Pressing Plate onto the Pressing Cushion. With water in the reservoir tank, press the Steam Burst Control 6 to 7 times. Avoid touching the hot metal surfaces or leaving your hand in the bursts of steam.