Buffalo Tech LinkStation EZ User manual

User Manual

LS-CL

LinkStation EZ

www.buffalotech.com

35010667 ver.1 2-01 C20-005 v1.1

Introduction

Congratulations on your new LinkStation EZ. This user manual is intended to assist you in configuring it.

Because we’re constantly updating our products, the images and text in this manual may vary slightly from the images and text displayed by your LinkStation. These changes are minor and should not affect the ease of setup adversely. As time passes, future user interfaces, updated software, and later versions of this manual may be freely available for download at our web site www.buffalotech.com.

For best results, attach the LinkStation EZ to an uninterruptable power supply (UPS). Back up all your stored files regularly. See pages 51 - 55 for instructions on how to use the

LinkStation EZ’s built-in backup utility.

If you run into difficulties or need additional help, feel free to contact our technical support.

Contact information for Buffalo Technology and our technical support is available on pages

70 and 71.

2

Table of Contents

Back Panel Layout ......................................................................... 4

Installation .................................................................................... 5

Power Mode Switch ........................................................................ 8

Using your LinkStation with a PC ................................................. 9

Using your LinkStation with a Mac® ............................................ 13

Add USB Devices ........................................................................ 17

Front Panel Layout ..................................................................... 18

Function Button .......................................................................... 19

Advanced Settings ...................................................................... 23

Network Settings .......................................................................... 25

Disk Management ........................................................................ 27

Shared Folders ............................................................................ 32

Groups ........................................................................................ 36

Users ........................................................................................... 37

Passwords ................................................................................... 38

WebAccess ................................................................................... 39

Installing a Printer ....................................................................... 44

Troubleshooting Multiple Shares..................... ............................. 49

Backups ......................................................................................51

Time Machine..................... ......................................................... 55

Maintenance & Notification .......................................................... 56

System Status ............................................................................ 61

Client Utility ................................................................................ 65

Troubleshooting ........................................................................... 67

Technical Specifications ............................................................... 69

Contact Information (USA) ........................................................... 70

Contact Information (Europe) ...................................................... 71

GPL Information ..........................................................................72

3

Back Panel Layout

Auto

On

Off

USB

Power Mode Switch

Ethernet

(to Router)

Power Plug

4

Insert the LinkNavigator CD into your computer’s CD-ROM drive.

On a PC, setup should automatically launch. If it does not, manually launch setup.exe by pressing Start and selecting the Run... option.

When the Run dialog opens, type d:\LSnavi.exe (where d is the drive letter of your CD-ROM drive). Press OK to continue.

If you are installing the software on a Mac, open the CD and click

LinkNavigator to begin installation.

Installation

5

LinkNavigator Setup

Choose your preferred language. Mac users can skip this step.

Press the Begin Installation button. Click Next to step through the installation.

6

LinkNavigator Setup

The wizard will guide you through installation. Follow the directions on each screen and continue pressing Next to step through the installation.

When installation is complete, you may close the installation window.

7

Power

Mode

Auto

On

Off

Power Mode

The “Power Mode” switch on the back of the unit has three positions: “Auto”, “On”, and “Off”. The

“Auto” position automatically powers the unit on or off with your PC. If your PC is turned on the

LinkStation will power up; if the PC is turned off the LinkStation will power down.

You must have installed the NAS Navigator software on your PC for this feature to work. Otherwise, if you move the switch to “auto”, your unit will power down by itself and you will have to manually turn it back on.

Also note that the unit needs to be powered on if you want to use the Web Access feature. When using Web Access, it is best to leave the Power

Mode switch set to “On”.

Move the switch to the “Off” position to turn the

LinkStation off. It will take about 35 seconds to shut down. Do not unplug or interrupt power to the unit until shutdown is complete and all LEDs are off.

8

Using your LinkStation with a Windows PC

Two new icons will be on your desktop: Shortcut for LinkStation and

Buffalo NAS Navigator.

Clicking Shortcut for LinkStation takes you directly to the folders on your LinkStation. Share is the main folder that you can put files and folders in. Info contains a copy of your user manual.

The Buffalo NAS Navigator icon opens the LinkStation’s client utility.

Turn to page 65 for more on using the NAS Navigator client utility.

9

Accessing LinkStation Data from your PC

To Access LinkStation Data from a PC:

Your LinkStation uses folders to hold data. The default folder is called “share”. This folder is where you place data that you want to share with other users. You can create additional folders using the Shared Folders option. To start using your LinkStation, you can either click on the Shortcut for LinkStation on your desktop, or you may just use drive L in My

Computer, which setup has mapped to the default share in your LinkStation.

10


You can map additional drive letters to shares on your LinkStation.

From the Start menu, select Run.... Enter your LinkStation’s hostname (if you don’t know it, you can get it from the NASnavigator2 utility) or IP address. Press OK.

Your LinkStation should open. “Share” is a data folder in your

LinkStation by default. “Info” contains your user manuals. If you have created other folders, they will be visible here too. You can map drive letters to any of these folders.

11


From the Tools pull-down menu, select Map Network Drive. Choose a drive letter from the Drive: pull down menu. To specify the folder to map, either find it with Browse or enter \\LinkStation_

Name\share_name in the Folder: field, where LinkStation_Name is your LinkStation’s hostname

(page 21) and share_name is the name of a folder on your LinkStation. Check the Reconnect at

logon checkbox to have Windows connect to this mapped drive everytime it starts. When finished, press the Finish button. Your share is now mapped to a drive letter.

12

Using your LinkStation with a Mac

After installing the LinkNavigator software, your Mac will have two new icons on the desktop.

The LS-CLSettings.txt file contains the IP address of your LinkStation.

NAS Navigator is the LinkStation’s client utility.

With the information in the LS-CLSettings.txt file, you can easily connect to the LinkStation from any of your computers on your local network.

The NAS Navigator icon opens the LinkStation’s client utility. See page 65 for more on using the NAS Navigator client utility.

13

Accessing LinkStation Data from a Mac

You can add a link to your LinkStation’s share folder to your desktop by adding it to the Mac’s server list. Begin by clicking Go, and then choose Connect to Server.

14

In the Server Address field, enter your

LinkStation’s IP address in the form smb://

ipaddress (where “ipaddress” is your

LinkStation’s IP address), and click Connect.

You can get your LinkStation’s IP address from the LS-CLSettings.txt file on your desktop, or see page 16.


Select Guest and click on Connect. Note: If you have configured share permissions on your LinkStation, select Registered User and enter your login credentials.

Select the volume that you want to mount, such as share or share-mac, from the list of folders on the LinkStation.

The share will open. A link to it will appear on your desktop.

15


If you don’t know your LinkStation’s IP address, there are several ways to get it.

One simple method is to use the NAS Navigator client utility

(included on your CD) to find your LinkStation(s). Just click on the icon for your LinkStation and you’ll be able to read its

IP address.

The LS-CLSettings.txt file on your desktop contains the IP address of the LinkStation at the time that the setup program was run.

You can always get the LinkStation’s IP address from your router’s configuration utility. Many Buffalo routers list this information on the Client Monitor page, as shown to the right.

Consult your router’s documentation for instructions on identifying the LinkStation’s IP address.

16

LinkStation Expansion

LinkStation EZ has a USB 2.0 port on the rear. This port can be used for adding an external

USB Hard Drive or a USB Printer, or for connecting to a UPS. LinkStation will share connected

USB devices, allowing everyone on the network to use them. To connect a USB hard drive to your

LinkStation, simply plug it into the USB port.

Once your USB hard drive is connected, turn to the “Disk Management” section of this manual for information on configuring your LinkStation to use it.

To configure a USB printer, see “Installing a Printer”.

To configure UPS settings, see page 57.

Note that only one USB device may be used at a time. USB hubs are not supported.

17

Front Panel Layout

Power LED - Blue. Lit when the LinkStation is on. Flashes during boot or shutdown.

Function Button/LED - See the next page for instructions on using the function button.

Replaceable fan

18

Using the Function Button

Direct Copy - You can copy digital media files directly to the LinkStation Live from a USB storage device, such as a digital camera, USB flash drive, or external hard disk.

1. Connect your USB device to the port on the back of the LinkStation

Live. The function button will glow solid blue for 60 seconds.

2. While the Function button is still glowing blue, press it once.

The following folder is created automatically:

DirectCopy/pictures/yyyymmdd where yyyy is the year, mm is the month, and dd is the day.

The following filetypes will be copied to the folder: avi, divx, asf, mpg, mpe, m1v, vob, mts, m2ts, m2t, mpeg, mpeg2, vdr, spts, tp, ts, 3gp, mov, m4v, wmv, dvr-ms, xvid, mp4, m4v, jpg, jpeg, gif, png, tif, tiff, yuv, bmp, mp3, mpa, wma, aac, apl, ac3, lpcm, pcm, wav, m3u, m4a, mp4, m4b, aif, aiff, flac, ogg, mp2, mp1, mp4.

19

Using the Function Button

Initialization - You can easily bring your LinkStation EZ back to factory settings with the following steps.

1. Move the power switch to the ‘Off’ position. The LinkStation EZ will shut down after about 45 seconds.

2. While holding down the function button, move the power switch to the

‘On’ postion. The function button will begin to flash blue.

3. While the function button is still flashing, hold it pressed down for six seconds.

Dismount - Before disconnecting USB devices from the LinkStation EZ, they should be dismounted. Hold the function button down until the function LED glows blue, and then turns off. It’s now safe to unplug your

USB device.

Note: Unplugging USB devices without dismounting them first may corrupt your data!

20

Web Administration Tool

The Web Admin tool may be accessed at any time by typing the IP address of your LinkStation into the URL bar of a browser running on a computer connected to the same network as the LinkStation.

You may also open the Web Admin from NAS

Navigator by right-clicking on your LinkStation and choosing Open Web Admin from the menu.

21

Log in

This login prompt will appear. Enter admin for the user name. Until you change it, the password for the admin account will be password. Press the OK button when finished.

User name: admin

Password: password

Instructions for changing your password may be found on page 38.

22

Advanced Settings - Home

Welcome to your LinkStation’s Web Admin tool! Bookmark this page in your browser so it can be easily accessed for future configuration changes. If the LinkStation’s IP Address changes, you will need to recreate the link. You can also get here by typing http://LinkStation_Name into a Web browser, where LinkStation_Name is the name (hostname) of your LinkStation.

You are now at the Home screen. Notice that the Home button is lit up in yellow. You can navigate this menu by clicking on the buttons at the left of the screen. Here at “Home”, you can see basic information about your LinkStation’s current configuration. To exit Web Admin, click on logout or close the browser window.

23

Basic

You may modify your LinkStation’s hostname and description under Hostname Setup. A friendly, easy-to-remember name (e.g. “LinkStation”) is recommended.

Make sure that the date and time are correct in Date and Time Setup. To synchronize time settings with those in your computer, press

Use Local Time. To have your system time automatically set by an NTP server, enable NTP

Server and enter an IP Address for an NTP server

(e.g. 192.43.244.18) or click on the box below to use the supplied default NTP server.

Ensure that both the Display Language and the

Windows Client Language are set to languages that you’re comfortable with.

Once desired fields have been completed, press the Apply button.

24

Basic Settings

25

IP Address

In most networks, LinkStation will get its IP

Address automatically from a DHCP server.

You may disable DHCP here if you would rather set a static IP address manually. If DHCP is disabled and an IP Address is not set manually, it will default to 169.254.xxx.xxx with subnet mask 255.255.0.0. The LinkStation’s IP

Address, Subnet Mask, Default Gateway

Address, and DNS Server address may all be entered manually under IP Address Properties.

Ethernet Frame Size may also be set manually on this page. Only use JumboFrame settings when operating in a Gigabit environment where all other clients support the same JumboFrame setting.

Click Apply after making any changes.

Network (Workgroup/Domain)

If you do not participate in a Domain network, then please leave the Network Type selected as Workgroup and

Workgroup Name set to the name of your local workgroup.

To make your LinkStation a member of a workgroup or an NT domain, enter the appropriate information into the fields on this page and click Apply.

If using NT Domain, LinkStation must be added as a member computer in the Domain Server.

Setting NT Domain for network type integrates the

LinkStation with a Windows NT server. The LinkStation

Pro participates as a member device in the Domain network, allowing the LinkStation to use Users and Groups from the Domain.

Once you have finished, press Apply.

26

This page shows the properties for the drives in your LinkStation EZ. If you have a USB hard drive plugged into the linkstation, its properties will appear here as well.

Disk Management

27

28

USB Hard Drives

From here you can see your USB hard drive’s system information. If the hard drives’ information isn’t displayed properly, try restarting your USB hard drives and then restarting your LinkStation. Some USB hard drives must be reformatted from within

LinkStation before they can be assigned shares. Select Disk Format from the left-side menu to format your USB hard disk(s).

Note: Reformatting a drive will erase all data on it! Back up any data on the drive before reformatting it.

29

Disk Check

Disk Check checks any of your hard drives for errors. To use Disk Check, select the disk that you want to check from the target pulldown and click Select Target. Then click on Start

Disk Check.

Disk Format

30

To format a hard drive or array, select it from the Target Disk drop box. Choose the file system desired from the File System dropbox

(internal drives can only be formatted with XFS).

Note that FAT32 has a 4 gigabyte filesize limit for individual files. If you choose FAT32 for your file system, you will not be able to store single files larger than 4 gigabytes on the drive. Use of the XFS or EXT3 file systems is recommended.

Press Select Target Disk when done, and then

Start format.

Depending on the size of the target hard disk or array, a disk format may take several hours to complete. Shares on the LinkStation will not be accessible during the disk format.

Note: Reformatting a drive will erase all data on it! Back up any data on the drive before reformatting it.

31

Disk Erase

To remove all data from a Disk, use Disk Erase.

Once erased, this data cannot be restored.

Note: Disk Erase may take several hours to complete.

32

Folders

To add new shares on your

LinkStation, select Shared

Folders from the left side menu, and then click the Add button under Shared Folders Setup.

To delete a share or shares, check the checkbox next to the shares you’d like to delete, and press the Delete button.

Deleting shares will remove the share and erase all of the files and folders inside that share.

Add a new Shared Folder

To add a new shared folder, enter a name for it in the Shared Folder Name box and choose which

Disk Space it will reside in. You may also choose which operating systems and features the share will support by putting the appropriate checks next to Shared Folder Support, and whether the share supports the Recycle Bin by putting a selecting Enable or Disable. Enter a Shared

Folder Description and a Remote Backup Password if desired. Click Apply to build the new shared folder.

AppleTalk support is available for use with legacy Macs. Checking “Apple” by Shared Folder

Support turns on AppleTalk, letting you use your

LinkStation with older Macs. Note that AppleTalk files are limited to 2GB maximum filesize and 32 characters for filenames. If a folder with AppleTalk on is accessed from a modern OS through SMB, then these limitations will not apply.

Remote Backup Password will set a password on this share for other LinkStations that want to use it as a remote backup target. This password will not affect users attempting to access the share; it only affects remote LinkStations trying to access this share for to store backup files on it.

33

34

Access Restrictions

To use Access Restrictions for a share, select

Enable.

Highlight groups or users in the All Groups/

Users column and use the left-pointing arrow buttons (located just to the left of each box) to move individual groups or users from the All

Groups/Users column to the Read Only box (if you want to give them read access only) or all the way to the Writable box, if you want to give them full access to the share. Right-pointing arrows will move highlighted users or groups back to the right.

Click Apply when you have your groups and users in the appropriate boxes.

Shared Folders (Services)

To allow FTP Access to your LinkStation, choose Enable for FTP Server. To enable legacy

AppleTalk support, choose Enable for AppleTalk Protocol. Click Apply.

If enabled, FTP lets users access the LinkStation from anywhere. Type ftp://username:

password@IP_address into a browser window to access the LinkStation remotely. Users will have access to shares that they have local access rights to on the LinkStation. Your network administrator may need to forward traffic on port 21 of the router to the LinkStation’s LAN-side

IP address for FTP to work over the Internet. Enabling FTP is not recommended unless you’ve configured access restrictions.

35

Add a name and a description to the Add New

Group fields. Put checks next to each Member User that you want to be part of the group. Click Apply when your group is set up the way you want it.

Domain Groups are only visible if the LinkStation is participating in an Domain network.

Members can be added or removed from a group at any time by editing the group. This is done by clicking on the Group name on the main Group

Settings page.

36

Groups

Groups allow for easier management of permissions in some networks, specifically networks with a lot of users in different departments.

To Delete a group, put a check next to its name and click Delete. To add a group to your LinkStation, click Add.

The Add New User dialog will appear. Enter a User

Name, Password, and User Description for the new user and click the Apply button. If a user will be accessing the LinkStation from a Windows 95/98 computer, their password should be 15 characters or less. Mac OS 8 and OS 9 users’s passwords should be 9 characters or less. Users of other OSs may have passwords of up to 20 characters. Note:

In a Domain network, password changes will need to be made on the Domain Controller.

37

Users

LinkStation is preconfigured with two users,

admin and guest, out of the box. The admin and guest user accounts cannot be deleted. To delete any other user, put a check next to their name and click Delete. To add a new user, click

Add.

Enter the desired new password in both boxes and click Apply.

38

Changing User Passwords

To change an account’s password, click on the name of the account under Local User Settings.

Note: if a user name and password are used to log into a user’s windows computer or domain, the same user name and password should be used when creating the user’s account on the

LinkStation, or problems accessing shared folders may occur.

WebAccess

With Buffalo’s WebAccess, you can access your LinkStation from anywhere in the world with an

Internet connection. It’s easy to access your files, or share them with other people, wherever they may be.

WebAccess is set up from within the Web

Admin. First, select ‘Web Access’, and then

‘Service Setup’ from the menu on the left.

To use Webaccess, set ‘Web Access Service’ to

Enable.

You may enable SSL Encryption if desired.

Using ‘BuffaloNAS.com’ is recommended.

Otherwise, you’ll have to manage your own DNS settings.

‘Auto-Configure Firewall’ is also recommended if your router supports UPnP (most do since 2001).

If you choose not to enable this, you must manually configure your router and firewall to forward internal port 9000 to the Internet.

Choose a name for your BuffaloNAS account and a password (“key”). This name is the name that will be used to access your LinkStation and to share with your friends. The password for this protects other people from using it, so picking a strong password is recommended.

Click Help in the top right of the window for detailed information on each setting.

39

Configuring WebAccess

Select ‘Folders Setup’ in the left-side menu. Any shares on your

LinkStation will appear on the list to the right. Click on the icon beside it to select a share for web access.

Choose your desired level of Web Access from the ‘Web Access

Settings’ dropbox:

‘Disable’ will prevent remote access to this share through

WebAccess. This is the default setting.

‘Allow Anonymous’ will allow anyone to access the share. Choose this if you want your LinkStation share and all files on it to be freely available to everyone.

‘Allow All Groups/Users’ will allow only people who have an account on the LinkStation to access this share remotely.

‘Use Inherited Folder Permissions’ will allow people with an account on the LinkStation to access the share remotely only if they have read permissions on the specific share that they’re accessing.

Click the Apply button to save your changes.

40

To access your LinkStation remotely, open a browser window on any computer connected to the Internet and go to

buffalonas.com.

In the dialog box, type the BuffaloNAS name that you set on page 39.

Alternately, you can go directly to your share by typing

BuffaloNAS.com/your_BuffaloNAS_name in the URL window.

The folders from your LinkStation’s share will appear. Files from anonymous shares will appear to the right. To see files from shares that are not set to anonymous, you will need to

log in. The ‘login’ link is on the top left corner of the page.

Using WebAccess

41

Clicking on individual files will give you other options, depending on the filetype. Clicking on the Audio link at the bottom left corner of the page will give you options for playing music files, including the opportunity to launch a

Flash-based music player that will stream your audio files directly through the Web interface.

42

Using WebAccess

To access individual folders on the right, click on their open links.

43

Direct Copy

To use Direct Copy, plug a USB device into the LinkStation and press the fuction button on the front within 60 seconds. Media files will be copied to the LinkStation automatically.

On this page, choose the folder on the LinkStation that Direct Copy copies files to and click Apply.

Printer Installation

If a USB printer is plugged in to your LinkStation, you can easily add the printer to any Windows

PC on your network. Follow these steps for each PC that you want to be able to access the printer.

• To begin, enable the print server in the Web Admin for your LinkStation.

44

• Access the LinkStation by pressing Start, selecting the Run... option, and entering \\LinkStation_Name (where LinkStation_

Name is the DNS name of your LinkStation). Press the OK button when finished.

• Right click on the lp icon and select Connect.


• You may receive a warning about installing from a trustworthy source. If you receive this message, press Yes to continue.

• You will receive a warning that the server does not have the proper drivers. Press OK to continue.

45

• The Add Printer Wizard will launch. Select the proper driver for your printer. If the specific printer is not in the list, you will be required to insert the CD that came with your printer into your PC’s CD-ROM drive and press the Have Disk button. Refer to your printer documentation for further information on installing your printer if necessary. Press OK to finish.

• If lp is the only printer installed on the PC, then it will automatically be set as the default printer. If it’s not the only printer, you may make it the default printer by clicking Printers and Faxes in Control Panel, right clicking on the lp printer icon and selecting the Set as

Default Printer option from the File drop-down menu.

46


• To print a test page or configure additional printer settings, right click on the lp printer icon and select

Properties. This will open the printer’s driver properties page.

• Press the Print Test Page button to print a test page. You can also browse through the available settings for the printer. Please refer to the printer’s documentation for more information on changing the printer’s settings.

NOTES: The printer installation process can be done on any machine on your network. Multiple machines may print to the printer at the same time. Repeat this process on all computers that require access to the printer.

Not all USB printers are supported. Multifunction printers are specifically not supported.

47


48

Print Server (Delete Print Queue)

If a corrupt print job is sent to a printer, printing may suddenly fail.

If your print jobs seem to be locked up, clearing the print queue may resolve the issue.

To delete the print queue, press the

Delete button. This will clear all current print jobs. Users will have to re-send any incomplete print jobs to the printer.

If there are still problems printing to the printer, then check the printer manufacturer’s documentation for troubleshooting information. Also, verify that the USB cable is securely fastened to both the printer and the

LinkStation. Finally, you may try turning the LinkStation off, turning the printer off, turning the printer back on, and then turning the

LinkStation back on again.

Accessing Multiple Shares from a single PC

When accessing multiple shares to a Windows

PC, you may see this error message.

This is caused by having multiple shares to the same resource using different login credentials.

The error occurs when connecting to at least one secure, restricted share. Due to a constraint in

Microsoft Windows, only one set of login credentials can access or map drive letters for a network resource such as the LinkStation. As such, only one username and password can be used while mapping drives to a PC. If unsecure, unrestricted shares are mapped and then an attempt to map a secure, restricted share is made from the same PC, this error will occur. To prevent this, you must create all mapped shares using the same login and password information. Please follow the steps on the next page to remedy this problem.

49

Mapping Multiple Shares

Accessing Multiple Shares from a single PC

When mapping any share, select the Connect using a different

user name option. A login and password prompt will appear.

Use the username and password required by any secure, restricted shares for all shares. All mapped shares on a single PC must use the same username and password!

If only unrestricted shares are being mapped, then it’s not necessary to set a username and password for shares. Multiple mapped drives to unrestricted shares can exist without a username or password as long as no restricted, secure shares are mapped. If an unrestricted share and a restricted share are both being mapped or accessed, use the restricted username and password for the unrestricted share login by using the Connect using a different user name option. This will allow a Windows PC to access both shares without any problems.

50

Backup

The LinkStation’s built-in backup utility can back up files on your LinkStation to an attached USB hard drive or to another

LinkStation on the local network. For best results, reformat attached USB hard drives with ext3 before use as backup storage.

If backing up to another LinkStation, then the target LinkStation should be connected to the same network as the LinkStation doing the backup. If the target LinkStation is on a different subnet or network, then you’ll need to create a VPN connection between the two networks before it can be used as a backup target.

To create a backup job, click on a job number. The Edit Backup Job dialog will appear.

51

52

Edit Backup Job

A Backup Job can run regularly on a daily or weekly schedule, or immediately by appropriate choices in the Backup Job Schedule field. Date and Time for the backup may be entered, and Encryption and Compression enabled or disabled. Enable Overwrite Backup to have each scheduled backup write over the previous backup, or Differential Backups to backup only files changed since the previous backup.

Select the folder to be backed up from the

Local Backup Shared Folder dropbox, and the destination for the backup files from the

Destination Backup Shared Folder dropbox.

The destination folder may be on a USB drive attached to the LinkStation, or another

LinkStation on the network. Click on Select to approve the backup targets.

Click the Apply button when your backup job is set up the way you want it, or Clear Job to stop a job from running again.

LinkStation List

The LinkStation list shows other LinkStations in your network that you can configure network backups to.

Press Refresh to get a list of LinkStations on your network.

53

Disk Backup (Add LinkStation)

To add a remote LinkStation to your network, enter its numerical IP Address in the Remote

LinkStation IP Address field and click the Add to List button. For remote LinkStation backups, make sure both firewalls are configured to allow traffic in and out of their networks.

Note: Disk Backups between two LinkStations use port 8873 for encrypted backups and port 873 for backups with no encryption.

54

Time Machine

To use the LinkStation as a location for backups from a Mac running Time Machine, click Enable and then Apply.

55

56

Notification

If your LinkStation is remotely managed, you may choose to receive daily status reports and be notified of any disk events by email. To set this up, enable Mail Notification and enter the

IP Address of your SMTP server in the SMTP

Server Address field. Select a Subject line for the emails (i.e. “LinkStation Status Report”) and enter the email address of each person you want to receive notification emails into a

Recipient Mail Address field.

APC is a registered trademark of American Power Conversion Corporation.

57

UPS Settings

If using an Uninterruptible Power Supply, configure the LinkStation’s UPS settings here.

Supported UPS products include USB models in APC’s Smart-UPS and Back-

UPS series.

Note: Settings on this page can only be changed while a supported UPS is connected to the LinkStation.

58

Sleep Mode

You may configure up to three situations where the LinkStation powers down for a set period.

Example: To have the LinkStation enter sleep mode every night between noon and

3 pm, set a timer with Daily as the timer interval, 15:00 as the wakeup time, and

12:00 as the sleep time.

59

Restart

From the Restart page, press

Restart Now button to reboot the LinkStation, bringing it back to functionality after about 120 seconds.

Initialization is a reset procedure that restores all settings back to the default, out of box, configuration. All configuration, users, groups, and backup jobs are lost, but actual data and shares on the hard drive are NOT lost. If you want all data to be erased, erase the drive.

Specify whether the LinkStation shall keep its administrator password after a initialization or whether the password should be reset to the default password

(default password is password). Press the

Apply button once you make the selection.

Press the Restore button to begin the initialization process; this will restore all settings to factory defaults but will NOT erase the data on the hard drives.

60

Initialization

System Status (System Information)

This page shows you the System Information for your LinkStation.

Firmware updates are occasionally available from www.buffalotech.com for the LinkStation EZ.

These must be executed from a Windows PC on the same network. Your router, switch, or hub should pass through ports 8873 and 22939 for this to work (most do).

61

System Status (USB Details)

This page shows you details on USB hard drives and UPSs plugged into your LinkStation. In this example, no USB hard drives are plugged in to the LinkStation.

62

63

System Status (Drive Properties)

This page shows you the properties of all hard drives in and attached to your

LinkStation.

Network Information

This page shows you the System Information for your network connection.

64

65

Client Utility

This is the Buffalo NASnavigator2 Client Utility.

Installed on your PC, it allows you to access each of the LinkStations (and TeraStations) on your network. Click View to get icons for each of your LinkStations. Highlight each tab to show the Host Name, Workgroup, IP Address, and Subnet Mask, Gateway, and MAC Address of the associated LinkStation, as well as the firmware version it’s running.

Right-click on a LinkStation for more options.

You can open the Web Admin GUI, map a share to a drive letter, or create a shortcut on your desktop.

To change a LinkStation’s IP Address, click

Menu and choose Properties.

Client Utility

IP Address Setup

From the IP Settings tab, you may enter your IP Address and Subnet Mask manually, or enable your LinkStation to acquire them automatically from a DHCP server. Press OK when you’re done.

66

Troubleshooting

Disk Errors

If LinkStation encounters a disk error, it will be reported in the LinkStation status on the top of any of the Web-Based configuration screens. Run a Disk Scan in the event of this error. If that doesn’t work, try a reformat. Reformatting the drive will delete all of the data on it so try to backup any data you can before beginning. Finally, if none of the above solutions help, then please contact Technical Support for further assistance.

LED Flash Codes:

The blue LED will flash to indicate error type:

3 flashes - Partition problem with hard drive. Reformat the hard drive.

4 flashes - RAID problem.

5 flashes - ROM problem.

6 flashes - Hard Drive not recognized.

7 flashes - Problem with motherboard (RAM, LAN, or Hard Drive controller).

67

Fan Replacement

Remove the screw from the top of the LinkStation. The fan will now slide straight out to the side.

Unplug the connector by pulling it straight up.

68

Technical Specifications

Data Transfer Rates:

Hard Drives:

Main Connector Type:

USB Interface:

Protocol Support:

Power Supply:

Client OS Support:

Power Consumption:

Dimensions:

Weight:

Operating Environment:

10/100/1000 Mbps

3.5” SATA

RJ-45 (Ethernet)

USB 2.0/1.1

TCP/IP

SMB, FTP, AppleTalk (File Sharing)

HTTP (Management)

NTP (Time Synchronization)

100-240V 50/60Hz

Windows

®

Vista™, XP, 2000,

Mac OS

®

10.3.9 or later

~24W (with no USB devices connected)

6.9” x 1.8” x 6.1” (174 x 45 x 156 mm)

~17.6 ounces (.5 kg)

41°- 95° F, 5°- 35° C; 20-80% non-condensing

Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

69

Contact Information (North America)

Buffalo Technology USA Inc.

11100 Metric Blvd., Suite 750

Austin, TX 78758

GENERAL INQUIRIES

Monday through Friday

8:30am-5:30pm CST

Direct: 512-794-8533 | Toll-free: 800-456-9799 | Fax: 512-794-8520 | Email: sales@ buffalotech.com

TECHNICAL SUPPORT

North American Technical Support by phone is available 24 hours a day, 7 days a week. (USA and Canada).

Toll-free: (866) 752-6210 | Email: [email protected]

70

Contact Information (Europe)

Buffalo Technology UK Ltd.

2 Bracknell Beeches, Old Bracknell Lane

Bracknell, Berkshire, RG12 7BW

United Kingdom

GENERAL INQUIRIES

Email: [email protected]

TECHNICAL SUPPORT

Buffalo Technology provides technical support in English, German, French, Italian and

Spanish. For opening hours and relevant telephone numbers, please go to: www.buffalo-technology.com/contact

71

GPL Information (North America)

Source code for most Buffalo products is available at http://opensource.buffalo.jp

To have a copy of the source code for an individual product mailed to you, please send one individually packaged self addressed padded CD shipping envelope containing a blank CD-R to the following address:

Buffalo Technology USA Inc.

11100 Metric Blvd., Suite 750

Austin, TX 78758

Attn. GPL Department

Within the envelope containing the self addressed padded CD shipping envelope, please include a bank draft or money order for $20 (USD) (made out to Buffalo Technology) to cover our handling fee, postage and

CD preparation. The CD-R should have the name of the product and revision number clearly written on the actual CD-R (not on the insert).

Sorry, but we do not send GPL source code in bulk. Source code for a single product will be sent with each request.

72

GPL Information (Europe)

Source code for most Buffalo products is available at http://opensource.buffalo.jp

To have a copy of the source code for an individual product mailed to you, please send one individually packaged self addressed padded CD shipping envelope containing a blank CD-R to the following address:

Buffalo Technology Ireland Ltd

Free Zone East, Shannon, Co. Clare

Ireland

Attn. GPL Department

Within the envelope containing the self addressed padded CD shipping envelope, please include a bank draft or money order for €20 (Euro) (made out to Buffalo Technology) to cover our handling fee, postage and CD preparation. The CD-R should have the name of the product and revision number clearly written on the actual CD-R (not on the insert).

Sorry, but we do not send GPL source code in bulk. Source code for a single product will be sent with each request.

73

No results