Automatic IP assignment. Bosch NDC-225-PI
Add to My manualsadvertisement
82 en | Advanced Mode
6.8
Network
Network
> Network Access
> Advanced
>
>
Multicast
FTP Posting
IP Camera 200 Series
6.8.1
Network Access
The settings on this page are used to integrate the device into a network. Some changes only take effect after a reboot. In this case Set changes to Set and Reboot.
1.
Make the desired changes.
2.
Click Set and Reboot.
The device is rebooted and the changed settings are activated.
If the IP address, subnet mask, or gateway address is changed, then the device is only available under the new addresses after the reboot.
Automatic IP assignment
If a DHCP server is employed in the network for the dynamic assignment of IP addresses, activate acceptance of IP addresses automatically assigned to the device.
Certain applications (Bosch Video Management System, Archive
Player, Configuration Manager) use the IP address for the unique assignment of the device. If using these applications, the DHCP server must support the fixed assignment between IP address and MAC address, and must be appropriately set up so that, once an IP address is assigned, it is retained each time the system is rebooted.
IP address
Enter the desired IP address for the camera. The IP address must be valid for the network.
Subnet mask
Enter the appropriate subnet mask for the set IP address.
AR18-10-B012 | v1.5 | 2011.01
Installation and Operation Manual Bosch Security Systems
advertisement
Related manuals
advertisement
Table of contents
- 30 Password
- 31 Confirm password
- 36 Camera ID
- 36 Camera name
- 36 Initiator extension
- 37 Password
- 37 Confirm password
- 38 Date format
- 38 Device date / Device time
- 38 Note:
- 38 Device time zone
- 38 Daylight saving time
- 39 Note:
- 39 Time server IP address
- 39 Time server type
- 39 Camera name stamping
- 40 Time stamping
- 40 Display milliseconds
- 40 Alarm mode stamping
- 40 Alarm message
- 40 Video watermarking
- 41 Website language
- 41 Company logo
- 41 Note:
- 41 Device logo
- 42 Transmit audio
- 42 Show alarm inputs
- 42 Show relay outputs
- 42 Show VCA metadata
- 42 Show event log
- 42 Show system log
- 43 Allow snapshots
- 43 Allow local recording
- 43 Path for JPEG and video files
- 43 Save event log
- 43 File for event log
- 43 Save system log
- 43 File for system log
- 44 Contrast (0...255)
- 44 Saturation (0...255)
- 44 Brightness (0...255)
- 44 White balance
- 44 R-gain
- 44 G-gain
- 45 B-gain
- 45 IR control
- 45 Default
- 46 Define profiles
- 47 Profile Configuration
- 47 Profile name
- 47 Target bit rate
- 47 Maximum bit rate
- 48 Encoding interval
- 48 Video resolution
- 48 Expert Settings
- 48 GOP structure
- 48 I-frame distance
- 48 I-frame quality
- 48 P-frame quality
- 49 Default
- 50 Select H.264 Settings
- 50 Preview >>
- 50 Note:
- 51 JPEG stream
- 51 Note:
- 52 Camera LED
- 52 Mirror image
- 52 Main frequency and Operation environment
- 52 Exposure/frame rate
- 52 Note:
- 54 Device manager
- 54 Note:
- 54 Recording media
- 54 iSCSI Media
- 55 Local Media
- 55 Note:
- 55 Activating and Configuring Storage Media
- 55 Note:
- 56 Note:
- 56 Formatting Storage Media
- 56 Deactivating Storage Media
- 58 Stream profile settings
- 58 Recording includes
- 58 Standard recording
- 59 Alarm recording
- 59 Alarm triggers
- 61 Weekdays
- 61 Holidays
- 62 Profile names
- 62 Activate recording
- 62 Recording status
- 63 Connect on alarm
- 63 Number of destination IP address
- 63 Destination IP address
- 63 Destination password
- 64 Video transmission
- 64 Stream
- 64 Remote port
- 64 Video output
- 65 Decoder
- 65 SSL encryption
- 65 Auto-connect
- 65 Audio
- 67 Aggregation time [s]
- 68 Analysis type
- 68 Motion detector
- 68 Note:
- 68 Sensitivity
- 69 Minimum object size
- 69 Debounce time 1 s
- 69 Selecting the area
- 69 Tamper detection
- 70 Sensitivity
- 70 Trigger delay [s]
- 70 Global change (slider)
- 70 Global change
- 70 Scene too bright
- 71 Scene too dark
- 71 Scene too noisy
- 71 Reference check
- 71 Disappearing edges
- 72 Appearing edges
- 72 Selecting the area
- 73 Weekdays
- 73 Holidays
- 73 Deleting Holidays
- 75 Trigger
- 75 Trigger active
- 75 Trigger inactive
- 75 Delay [s]
- 76 Audio alarm
- 76 Name
- 76 Signal Ranges
- 76 Threshold
- 76 Sensitivity
- 77 Send alarm e-mail
- 77 Mail server IP address
- 77 SMTP user name
- 77 SMTP password
- 77 Format
- 77 Attach JPEG from camera
- 78 Destination address
- 78 Sender name
- 78 Test e-mail
- 80 Name
- 80 Idle state
- 80 Operating mode
- 81 Relay follows
- 81 Relay name
- 81 Trigger relay
- 82 Automatic IP assignment
- 82 IP address
- 82 Subnet mask
- 83 Gateway address
- 83 DNS server address
- 83 Details >>
- 83 Video transmission
- 83 HTTP browser port
- 83 HTTPS browser port
- 84 RCP+ port 1756
- 84 Telnet support
- 84 Interface mode ETH
- 84 Network MSS [Byte]
- 84 iSCSI MSS [Byte]
- 84 Enable DynDNS
- 84 Note:
- 85 Host name
- 85 User name
- 85 Password
- 85 Force registration now
- 85 Status
- 86 SNMP
- 86 1. SNMP host address / 2. SNMP host address
- 86 SNMP traps
- 86 Authentication (802.1x)
- 87 RTSP port
- 87 UPnP
- 87 Note:
- 87 TCP metadata input
- 88 Enable
- 88 Multicast Address
- 88 Port
- 88 Streaming
- 88 Multicast packet TTL
- 89 File name
- 89 Posting interval
- 89 FTP server IP address
- 89 FTP server login
- 89 FTP server password
- 89 Path on FTP server
- 89 Max. bit rate
- 90 Firmware
- 91 Configuration
- 91 SSL certificate
- 92 Maintenance log
- 92 Note:
- 94 Display Stamping
- 99 Slide control
- 99 Bookmarks