advertisement
Chapter 5
CURRENT DATE AND TIME ADJUSTMENT
Controls procedure
1. Remove and restore the stove power supply using the master switch or using the power supply cable.
2. The stove will fi rst display the microprocessor version ( OVEN_3 or successive), “LANGUAGE”,
“CLOCK”, “LEVEL” and then “OFF”.
3.
4.
When “ CLOCK” appears, press button 5 to access the adjustment mode.
Display D1 will show a day of the week (from DAY 1 to DAY 7) :
5. use keys 2 and 3 to set the current day and confi rm using button 5.
D1 display
DAY 1
DAY 2
DAY 3
DAY 4
DAY 5
DAY 6
DAY 7
Meaning
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
6. Display D1 will show the current time, the hours fl ashing while the minutes are fi xed: use keys 2 and
3 to adjust the time and then confi rm using key 5.
7. At this point the hours will become fi xed and the minutes will start to fl ash: use keys 2 and 3 to adjust the minutes.
To go back to selection of the hours, press button 4 again or escape and confi rm using button 1.
BASIC INSTRUCTIONS
The stove you have purchased uses pellet fuel. This type of material is obtained from natural waste from the machining of wood. By means of a special process that does not require the use of any binding agent and additive, the waste is compressed in industrial machinery under high pressure and it becomes solid wooden pellets.
IT IS PROHIBITED to burn non-pelletised raw materials inside our stoves. The failure to comply with these prescriptions voids all guarantees and could jeopardise the safety of the appliance.
The following recommendations must be followed the fi rst two or three times the stove is ignited:
no children must be present because the vapours emitted can be noxious to health. Adults should also avoid long stays.
Do not touch the surfaces as they could still be unstable.
Air the room well several times.
The hardening of the surfaces is terminated after several heating processes.
This appliance must not be used to burn waste.
18
PRODUCT FUNCTIONALITY
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 WARNINGS AND SAFETY DEVICES
- 8 WHAT ARE PELLETS?
- 8 PELLET STORAGE
- 8 PELLET LOAD
- 9 SAFETY DEVICES
- 9 WARM AIR BLOWER BREAKDOWN
- 9 FUME EXHAUSTER BREAKDOWN
- 9 PELLET FEED MOTOR BREAKDOWN
- 9 IGNITION FAILURE
- 9 TEMPORARY POWER FAILURE
- 9 ELECTRICAL SAFETY
- 9 EXHAUST FUME SAFETY
- 9 PELLET OVERHEATING SAFETY
- 10 ASSEMBLY AND INSTALLATION INSTRUCTIONS
- 10 GLOSSARY
- 11 INSTALLATION
- 11 ADMISSIBLE INSTALLATIONS
- 11 PROHIBITED INSTALLATIONS
- 12 CONNECTION TO THE EXHAUST VENTING SYSTEM
- 12 EXHAUST CHANNEL OR PIPE
- 13 CHIMNEY OR SINGLE FLUE
- 15 CONNECTION TO THE FLUE AND COMBUSTION PRODUCT EXHAUST VENTING
- 15 CHIMNEY CAP
- 16 CONNECTION TO EXTERNAL AIR INTAKES
- 16 INSULATION, TRIMS, FACINGS, AND SAFETY PRECAUTIONS
- 16 NATIONAL, REGIONAL, PROVINCIAL AND MUNICIPAL LAWS
- 17 PRODUCT FUNCTIONALITY
- 17 CONTROL BOARD
- 17 LANGUAGE SELECTION
- 18 CURRENT DATE AND TIME ADJUSTMENT
- 18 BASIC INSTRUCTIONS
- 19 IGNITION
- 19 STOVE FUNCTIONING
- 19 NORMAL FUNCTIONING
- 20 SWITCH-OFF
- 21 REMOTE CONTROL
- 22 ROOM THERMOSTAT
- 22 DIGITAL THERMOSTAT (AS PER STANDARD)
- 22 MECHANICAL THERMOSTAT (OPTIONAL)
- 22 MECHANICAL THERMOSTAT INSTALLATION (OPTIONAL)
- 22 MECHANICAL THERMOSTAT FUNCTIONING
- 23 ACTUATOR)
- 24 USER PARAMETERS
- 24 OVEN FUNCTIONING MODES
- 25 NORMAL FUNCTIONING (NO TIMER)
- 25 TIMED FUNCTIONING (WITH TIMER)
- 26 NORMAL FUNCTIONING (NO TIMER)
- 26 TIMED FUNCTIONING (WITH TIMER)
- 26 WEEKLY PROGRAMMER
- 29 DAY-NIGHT TEMPERATURE FUNCTION
- 30 PELLET FEED ADJUSTMENT
- 32 CLEANING
- 33 CONNECTION TO THE FLUE
- 34 POT DIVIDER
- 35 PRODUCT DISPLAY TABLES
- 39 WARRANT