advertisement
Chapter 7
ROOM THERMOSTAT
DIGITAL THERMOSTAT (AS PER STANDARD)
The appliance can control the room temperature using a digital thermostat, which can lower the heating power to minimum when a pre-set temperature is reached.
1. When the stove is started and has entered normal functioning mode, display D1 will show a number
(e.g. 21°C); this value indicates the room temperature.
2. Use buttons 2 or 3 to enter the thermostat setting and the display will show a fl ashing word that alternates at every impulse with “SET” and the temperature to be set; by pressing 2 the value decreases and by pressing 3 it increases.
3. When the desired temperature has been adjusted let “ SET” disappear from the display.
4. Adjust the desired heating power using buttons 4 and 5.
When the appliance reaches the temperature set it automatically goes to a minimum functioning mode and the relative luminous indicator switches-off in display D1.
If digital thermostat functioning thermostat is to be excluded, use button 3, to take the temperature to maximum until “MANUAL” appears in display D1.
The same functions can be obtained using the remote control.
MECHANICAL THERMOSTAT (OPTIONAL)
N.B: Installation must be performed by an authorised technician.
It is possible to thermostat a room adjacent to the room where the stove is positioned: just connect a mechanical thermostat (boiler type) following the procedure described in the next point (it is recommended to position the optional mechanical thermostat at a height of 1.50m from the ground).
MECHANICAL THERMOSTAT INSTALLATION (OPTIONAL)
N.B: Installation must be performed by an authorised technician.
1. Switch the appliance off using the master
2. switch positioned on the rear of the stove
3.
4.
Remove the plug from the socket
Refer to the wiring diagram to connect the two thermostat cables onto the relative clamps positioned don the rear of the machine, one is red and the other black.
MECHANICAL THERMOSTAT FUNCTIONING
1. Set the desired heating power using buttons 4 and 5.
2.
Using button 2 take the room temperature to minimum and “ MINIMUM” will appear on the display.
Adjust the desired room temperature using the thermostat (e.g. 21 C°) and “ T ON” will appear on the display.
3. When the stove reaches the desired temperature, it will go to minimum working conditions
(“MINIMUM” will appear on D1). If the temperature lowers, the appliance will go back to “T ON” taking back the previously left functioning setting.
22
ROOM THERMOSTAT
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 WARNINGS AND SAFETY DEVICES
- 8 WHAT ARE PELLETS?
- 8 PELLET STORAGE
- 8 PELLET LOAD
- 9 SAFETY DEVICES
- 9 WARM AIR BLOWER BREAKDOWN
- 9 FUME EXHAUSTER BREAKDOWN
- 9 PELLET FEED MOTOR BREAKDOWN
- 9 IGNITION FAILURE
- 9 TEMPORARY POWER FAILURE
- 9 ELECTRICAL SAFETY
- 9 EXHAUST FUME SAFETY
- 9 PELLET OVERHEATING SAFETY
- 10 ASSEMBLY AND INSTALLATION INSTRUCTIONS
- 10 GLOSSARY
- 11 INSTALLATION
- 11 ADMISSIBLE INSTALLATIONS
- 11 PROHIBITED INSTALLATIONS
- 12 CONNECTION TO THE EXHAUST VENTING SYSTEM
- 12 EXHAUST CHANNEL OR PIPE
- 13 CHIMNEY OR SINGLE FLUE
- 15 CONNECTION TO THE FLUE AND COMBUSTION PRODUCT EXHAUST VENTING
- 15 CHIMNEY CAP
- 16 CONNECTION TO EXTERNAL AIR INTAKES
- 16 INSULATION, TRIMS, FACINGS, AND SAFETY PRECAUTIONS
- 16 NATIONAL, REGIONAL, PROVINCIAL AND MUNICIPAL LAWS
- 17 PRODUCT FUNCTIONALITY
- 17 CONTROL BOARD
- 17 LANGUAGE SELECTION
- 18 CURRENT DATE AND TIME ADJUSTMENT
- 18 BASIC INSTRUCTIONS
- 19 IGNITION
- 19 STOVE FUNCTIONING
- 19 NORMAL FUNCTIONING
- 20 SWITCH-OFF
- 21 REMOTE CONTROL
- 22 ROOM THERMOSTAT
- 22 DIGITAL THERMOSTAT (AS PER STANDARD)
- 22 MECHANICAL THERMOSTAT (OPTIONAL)
- 22 MECHANICAL THERMOSTAT INSTALLATION (OPTIONAL)
- 22 MECHANICAL THERMOSTAT FUNCTIONING
- 23 ACTUATOR)
- 24 USER PARAMETERS
- 24 OVEN FUNCTIONING MODES
- 25 NORMAL FUNCTIONING (NO TIMER)
- 25 TIMED FUNCTIONING (WITH TIMER)
- 26 NORMAL FUNCTIONING (NO TIMER)
- 26 TIMED FUNCTIONING (WITH TIMER)
- 26 WEEKLY PROGRAMMER
- 29 DAY-NIGHT TEMPERATURE FUNCTION
- 30 PELLET FEED ADJUSTMENT
- 32 CLEANING
- 33 CONNECTION TO THE FLUE
- 34 POT DIVIDER
- 35 PRODUCT DISPLAY TABLES
- 39 WARRANT