advertisement
Before using for the first time
To programme the water hardness level
Each time a button is pressed, one of the indicator lights will flash and light up in the control panel. However, only the indicator lights mentioned in the following programming process stages are significant.
The programming procedure can be cancelled at any time by pressing the
On/Off button
K. The procedure can then be re-started from the beginning again.
^ Switch the dishwasher off with the
On/Off button
K.
^ Press the Start/Stop button in and
whilst holding it in switch the dishwasher on using the On/Off button K.
Keep the Start/Stop button pressed in until the "Start/Stop" indicator light comes on.
If this does not happen, start the procedure from the beginning again.
^ Press the Delay start button twice.
The "Delay start" indicator will flash briefly twice at intervals.
The characters " p 1 5" will flash one after the other in the display.
This means that the water hardness level has been set at 15 °d (2.7 mmol/l)
(factory setting).
The value which has been set for the water hardness is shown as a figure after the " p" in the display (see chart).
^ Use the Start/Stop button to select the value which equates to your water hardness level.
Each press on the button moves you up a level. When the highest water hardness level is reached, the setting starts from the beginning again.
^ Switch the dishwasher off with the
On/Off button
K.
16
advertisement
Related manuals
advertisement
Table of contents
- 5 Guide to the appliance
- 5 Appliance overview
- 6 Control panel
- 7 Warning and Safety instructions
- 12 Caring for the environment
- 12 Disposal of the packing material
- 12 Disposal of your old appliance
- 13 Energy saving washing
- 14 Before using for the first time
- 14 To open the door
- 14 To close the door
- 14 Safety lock
- 15 Water softener
- 16 To programme the water hardness level
- 17 To call up the water hardness level in the display
- 18 Before using the appliance for the first time you require
- 18 Filling the salt reservoir
- 19 Salt indicator
- 20 Rinse aid
- 20 Adding rinse aid
- 21 Rinse aid indicator
- 22 Setting the rinse aid dosage
- 23 Loading the dishwasher
- 24 Items not suitable for dishwashers
- 25 Upper basket
- 25 Hinged cup rack
- 26 Adjusting the upper basket
- 27 Lower basket
- 27 Hinged spikes
- 29 Bottle holder (depending on model)
- 30 Cutlery
- 30 Cutlery tray (depending on model)
- 31 Operation
- 31 Detergent
- 32 Adding detergent
- 33 Switching on
- 33 Selecting a programme
- 33 Starting a programme
- 34 Time display
- 34 Programme sequence indicators
- 34 At the end of a programme
- 34 Switching off
- 35 Unloading the dishwasher
- 35 Interrupting a programme
- 35 Changing a programme
- 36 Additional functions
- 36 Extra options
- 36 Turbo
- 36 Combi tabs
- 37 Delay start
- 39 Factory default setting
- 40 Adjust Sensor wash
- 41 Cleaning and care
- 41 Cleaning the wash cabinet
- 41 Cleaning the door and the door seal
- 41 Cleaning the door front
- 42 Cleaning the filters in the wash cabinet
- 44 Cleaning the spray arms
- 45 Problem solving guide
- 45 Technical problems
- 47 The dishwasher does not fill/drain
- 48 General problems
- 49 Noises
- 50 Unsatisfactory washing result
- 53 Maintenance
- 53 Cleaning the water inlet filter
- 54 Cleaning the drain pump and non-return valve
- 55 After sales service
- 55 Repairs
- 55 Future updates
- 55 For testing institutes
- 56 Programme chart
- 60 Optional accessories
- 61 Electrical connection
- 62 Plumbing
- 62 The Miele waterproof anti-leak system
- 62 Connection to the water supply
- 63 Drainage
- 64 Technical data